Ardumower ardumower issues

Ardumower / ardumower

Develop an open source robotic lawn mower (HW+SW reference platform)

239 stars 135 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

We all live in a yellow-submarine

#147 robomike closed 2 years ago
0
Robomow signal

#146 xjustbmw opened 2 years ago
0
Feature request: OpenHab compatibility

#145 Supermagnum opened 3 years ago
0
DRV8308-Testprogram - too high spi frequency

#144 Loevenich69 opened 3 years ago
0
extra mod: robomower + dog poop scooper

#143 allanlaal opened 3 years ago
3
changes to prevent Failed to readADXL345B

#142 Geo-Ron closed 3 years ago
1
PCB1.4 charging current measurement

#141 greymfm opened 3 years ago
1
An even cheaper bump sensor?

#140 cinderblock opened 3 years ago
1
PCB 1.4

#139 Kralg closed 3 years ago
13
Is this project stopped?

#138 darrepac closed 3 years ago
2
update to new syntax required: ESP8266SerialWifiBridge

#137 pizzadriver1 opened 3 years ago
0
add temperature sensor DHT22

#136 netlars closed 4 years ago
0
Fix turns with IMU in use

#135 rstonkus closed 4 years ago
0
IMU i2c reset

#134 rstonkus closed 4 years ago
0
Wrapper for motor drivers / firmware 1.0a9

#133 GitHubUser598 opened 4 years ago
0
Code cleanups till 2020-05-14

#132 tobylorenz closed 4 years ago
2
Change in software reset for Due

#131 Fejitatete opened 4 years ago
0
mow motor modulation

#130 xjustbmw opened 5 years ago
0
perimeterV2 10bits analog read

#129 eimix opened 5 years ago
0
adcman/perimeter new version with "differential signal" does not have 10bit readings

#128 eimix opened 5 years ago
0
2nd mower motor

#127 jussipu closed 5 years ago
0
Kann Communications Menü nicht öffnen

#126 mest2101 closed 6 years ago
0
RMCS

#125 PaddyCube closed 6 years ago
2
[doc] ardumower simulator - link outdated

#124 QuadCorei8085 opened 6 years ago
0
Perimeter wird ignoriert, wenn Bumper/Sonar aktiv ist

#123 surfingmicha opened 7 years ago
2
Merge pull request #1 from Ardumower/master

#122 wm1962 closed 7 years ago
0
Mixed min/max parameter for batFactor and batChgFactor

#121 surfingmicha opened 7 years ago
0
fix advanced perimeter tracking

#120 Holoratte closed 7 years ago
1
PCB1.3: show DHT22 temperature in pfodApp

#119 greymfm closed 3 years ago
1
PCB 1.3: ultrasonic sliders

#118 greymfm closed 3 years ago
1
PCB1.3: Add button to turn OFF robot

#117 greymfm opened 7 years ago
0
BumperDuino: when driving reverse, robot should drive forward if bumper triggered

#116 greymfm opened 7 years ago
0
Mow is ON/OFF should be a real switch, add direction switch

#115 greymfm opened 7 years ago
3
Advanced perimeter tracking

#114 Holoratte closed 7 years ago
3
Update on POUTREV: ends on Perimeter Inside or Timeout

#113 ainagtur closed 7 years ago
3
Batteryspannung wird nicht ausgewertet

#112 Holoratte closed 7 years ago
1
New sonarSlowBelow was missing in Console.print

#111 ainagtur closed 7 years ago
0
I2C requestFrom

#110 greymfm closed 3 years ago
1
missing manual

#109 greymfm closed 3 years ago
4
sonar - add software switch for stop on obstacle

#108 greymfm closed 7 years ago
0
Jürgen's optimized battery charging/station related values

#107 greymfm closed 3 years ago
0
DS1307 module EEPROM settings

#106 greymfm opened 7 years ago
2
ESP8266 soft access point and pfodApp

#105 greymfm opened 7 years ago
0
Drop sensoren

#104 greymfm opened 7 years ago
0
LCD Code

#103 greymfm opened 7 years ago
0
PCB 1.3 charging circuit

#102 greymfm opened 7 years ago
0
sonar test mode

#101 greymfm closed 3 years ago
1
External tilt pin

#100 greymfm closed 3 years ago
1
Modify sender to run on ATmega168 chips

#99 Tpbradley opened 7 years ago
0
Verify charging relay (pinChargingEnable) for PCB 1.3

#98 greymfm opened 7 years ago
0