issues
search
COAST-Lab
/
Open-Water-Level
An open-source, low-cost, DIY ultrasonic water level sensor
MIT License
9
stars
3
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Fabrication Updates
#48
gracelower
opened
1 month ago
0
Get new zenodo link
#47
SUPScientist
opened
1 month ago
0
Updated code and instructions to simplify user experience
#46
gracelower
closed
1 month ago
3
Fixing Serial.print issue; adding Log.info statements
#45
gracelower
closed
1 month ago
2
Assembly: Photos + Instructions
#44
gracelower
closed
1 month ago
0
Various updates to repo documentation
#43
gracelower
closed
1 month ago
0
Questions & Next Steps
#42
gracelower
opened
1 month ago
8
Updates to Fabrication & Firmware folders
#41
gracelower
closed
1 month ago
1
Open Water Level Documentation Enhancements
#40
gracelower
closed
1 month ago
0
Reorganize "Firmware" folders
#39
gracelower
closed
1 month ago
3
Reorganize "Fabrication" folder to reflect new versions of sensor
#38
gracelower
opened
2 months ago
2
Practice
#37
gracelower
closed
2 months ago
0
Updated 'Getting Started' instructions and photo folder
#36
gracelower
closed
2 months ago
0
Updated "Getting Started" instructions and photo folder
#35
gracelower
closed
2 months ago
0
Switch from Serial.print to Log.info
#33
SUPScientist
closed
1 month ago
11
Fit parts inside in more protected and reliable way
#32
SUPScientist
opened
4 months ago
5
Update readme.md
#31
dylan9081
closed
4 months ago
0
Update Readme.md
#30
dylan9081
closed
5 months ago
0
Updating Read me
#29
dylan9081
closed
5 months ago
0
Optimize sleep config
#28
SUPScientist
closed
4 months ago
1
Change Readme
#27
dylan9081
closed
5 months ago
0
Adding DataSheets to ReadMe
#26
dylan9081
closed
5 months ago
0
General issues observed/improvements needed
#25
SUPScientist
opened
6 months ago
3
Document modifications needed for google sheets
#24
SUPScientist
closed
6 months ago
0
Add table of contents to top of main readme
#23
SUPScientist
closed
5 months ago
4
Add thru holes to top end cap for solar panel mounting screws
#22
SUPScientist
opened
6 months ago
0
Test first issue
#21
dylan9081
closed
6 months ago
2
Add mechanical/plumbing parts to BOM
#20
SUPScientist
opened
7 months ago
1
Update BOM
#19
SUPScientist
closed
7 months ago
1
Particle update
#18
Stephen-Lail
opened
7 months ago
2
Document fabrication
#17
SUPScientist
closed
6 months ago
1
Design and build chassis for electronics
#16
SUPScientist
opened
9 months ago
1
Design better top end-cap
#15
SUPScientist
closed
9 months ago
3
Enclosure subdirectory is badly out of date
#14
SUPScientist
closed
7 months ago
7
attempted fix to issue of time after publish too short
#13
SUPScientist
closed
10 months ago
0
If SD card doesn't connect, system gets stuck in expensive cell connection loop
#12
SUPScientist
closed
6 months ago
4
Make single data buffer for serial, SD, and publish writing
#11
SUPScientist
closed
10 months ago
0
Accurate timing depends on good cloud connection
#10
SUPScientist
opened
10 months ago
1
Time from publish to sleep too short
#9
SUPScientist
closed
10 months ago
4
Condense print/SD write/publish data
#8
SUPScientist
closed
10 months ago
0
Make single data buffer for serial, SD, and publish writing
#7
SUPScientist
closed
10 months ago
2
Iss1
#6
SUPScientist
closed
10 months ago
0
Soldering problem
#5
SUPScientist
opened
10 months ago
0
Beautify your code!
#4
SUPScientist
opened
10 months ago
0
Add wiring instructions to getting started readme
#3
SUPScientist
closed
9 months ago
9
Break up PUBLISH_STATE to do separate tasks in separate states
#2
SUPScientist
closed
10 months ago
5
Change timing to collect sample at arbitrarily defined times
#1
SUPScientist
closed
10 months ago
5