FABtotum fabui-colibri issues

FABtotum / fabui-colibri

Web UI for FABtotum

GNU General Public License v2.0

18 stars 14 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Failing extruder temp jog

#222 BuffBro opened 1 year ago
0
Problem printing with PLA

#221 Morellid97 opened 4 years ago
0
Problem installing firmware

#220 Morellid97 closed 4 years ago
3
Unable to download the zip

#219 SJMSNH opened 4 years ago
0
Fabui upgrade raspberry Pi4?

#218 MIRCO3TEM opened 4 years ago
13
BEWARE! Colibri starving in blue light after update

#217 homahe opened 5 years ago
0
Problems installing

#216 cmuscata opened 5 years ago
7
installation problem

#215 giusediv opened 5 years ago
0
Vagrant box no longer available

#214 CryoRig closed 1 year ago
4
Image Download link nolonger working

#213 ekomenski opened 5 years ago
2
Problemi con la connessione lan

#212 frenzzz opened 6 years ago
1
Add soft-power-button daemon

#211 simone-fabteam opened 6 years ago
0
Scanning does nothing

#210 AndrewKillian opened 6 years ago
1
Nozzle calibration impossible after latest update

#209 homahe opened 6 years ago
0
Unable to update firmware

#208 andreu11 opened 6 years ago
1
Bluetooth

#207 daniel-fabteam closed 6 years ago
0
Add ability to reset multiple boards at once

#206 simone-fabteam closed 6 years ago
0
Fix Milling Head tool configuration

#205 simone-fabteam closed 7 years ago
0
Uneven Bed (Bad Bed Calibration)

#204 rayyash opened 7 years ago
2
Add classes to read thermistor values through GPIO pins

#203 simone-fabteam closed 7 years ago
0
WiFi passphrase can't contain some characters

#202 dr4Ke closed 7 years ago
2
Install on clean SD-Card failed after Reboot

#201 m-sja closed 7 years ago
3
Not working

#200 Fensterbank closed 6 years ago
4
Current sd_card latest does not boot anymore

#199 mgcrea closed 7 years ago
5
Make Colibri UI and firmware downloads/updates secure

#198 seppestas opened 7 years ago
0
Added priority update logic

#197 daniel-fabteam closed 7 years ago
0
Layer and Time error

#196 PaoloP74 closed 6 years ago
1
almost no filament get out of the nozzle

#195 florentmaye closed 6 years ago
3
Skip instead of Next in the 1st setup

#194 dmnc-net closed 7 years ago
2
First Time Boot hangs

#193 dmnc-net closed 7 years ago
1
RaspPi Camera Check-In

#192 brettdaniels closed 6 years ago
2
Warning: cannot extrude filament: the nozzle temperature is too low

#191 mgcrea closed 7 years ago
10
Fresh install not working anymore

#190 mgcrea closed 7 years ago
4
Photogrammetry scan does not finish

#189 AndrewKillian closed 7 years ago
2
not checked for updates during dashboard page load

#188 christopherwit closed 6 years ago
0
"Build plate needs to be flipped to the printing side"

#187 brettdaniels closed 7 years ago
3
Very Slow/Frozen Update

#186 brettdaniels opened 7 years ago
1
carriage issue

#185 florentmaye closed 6 years ago
0
jog controls pseudo classes don't work as intended

#184 christopherwit closed 6 years ago
1
first time setup notification

#183 christopherwit opened 7 years ago
0
Nozzle not heating after update

#182 brettdaniels closed 7 years ago
5
probe angle range

#181 christopherwit closed 6 years ago
3
Add probe angle calibration to first time setup

#180 christopherwit opened 7 years ago
0
Fab-UI Colibrì don't boot

#179 PaoloP74 closed 7 years ago
4
Print position variation

#178 florentmaye closed 6 years ago
1
Spool calibration issue

#177 florentmaye closed 6 years ago
7
Nozel heigth calibration issue

#176 florentmaye closed 6 years ago
13
pwm level during laser task not shown

#175 christopherwit closed 6 years ago
1
laser head reuse xyz position doesn't work

#174 christopherwit opened 7 years ago
1
Print bed crashed into the print head at start of print!

#173 LeiEng closed 6 years ago
5