NeonHorizon lipopi issues

NeonHorizon / lipopi

Guide to setting up LiPo batteries on the Raspberry Pi

GNU General Public License v3.0

416 stars 62 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Hum noise

#58 stahlhelm98 opened 2 years ago
5
Remove transparency from diagrams

#57 BenJuan26 closed 3 years ago
1
On-Off switch suggestion

#56 miki-mulet closed 3 years ago
2
Power down while charging => immediately off

#55 Felix79a closed 4 years ago
6
Variant for reusing switch for soft powerdown

#54 dtourolle closed 4 years ago
9
Bateria Raspberry

#53 muozam closed 4 years ago
0
Connecting LBO directly to a GPIO pin

#52 antfris closed 4 years ago
1
Using other DC-DC converters

#51 RChadwick7 opened 5 years ago
1
Why is wire to GND needed?

#50 slavapak closed 4 years ago
11
Is it possible to use other pins that are not UART?

#49 karlahaiat closed 5 years ago
2
Wiring from PowerBoost 1000c to RPi 3 B

#48 DarumasLegs closed 5 years ago
1
error during run process

#47 Davud2020 closed 5 years ago
1
step 13 not working. Pi powers off when releasing button

#46 MatayMayrany closed 5 years ago
4
Hold button 3 seconds to shut down

#45 RChadwick7 closed 5 years ago
1
Recommended code change

#44 RChadwick7 opened 5 years ago
8
Configuring the serial port without raspi-config

#43 RChadwick7 closed 5 years ago
1
bug fix for GPIO port other than 15

#42 cgalpin closed 6 years ago
7
EN pin on Vs instead of Bat ?

#41 rtatibouet closed 6 years ago
3
using other pin than 14

#40 yosorg closed 6 years ago
1
low battery light always on

#39 yosorg closed 6 years ago
2
Auto Power on part Deux

#38 cgalpin closed 6 years ago
26
lipopi.py script query

#37 satishgunjal closed 6 years ago
1
GPIO connection question

#36 satishgunjal closed 6 years ago
1
Pinnout question

#35 CoderFX closed 6 years ago
1
Pi Zero W powering as soon as battery is connected

#34 Goeste closed 6 years ago
8
added rc network changes to fork

#33 svenyonson closed 6 years ago
0
GPIO 14 does not stay high on power up (Pi Zero W version 1.1)

#32 svenyonson closed 6 years ago
26
UART and USB Serial

#31 markgeejw closed 6 years ago
1
Tx uart share with imu

#30 darkmoon3d closed 6 years ago
1
gpio switch from pitft gpio

#29 darkmoon3d closed 6 years ago
3
RPI3 with Stretch works like the others

#28 jeanrocco closed 7 years ago
3
LiPoPi Power Up / Power Down version low power reset

#27 robinsdl closed 7 years ago
9
question of software install on/off version

#26 jaysond04 closed 7 years ago
7
Single spdt switch working

#25 hex007 closed 7 years ago
6
Using a 3.3v linear regulator

#24 hex007 closed 7 years ago
1
raspi-config sets enable_uart=0

#23 jeanrocco closed 7 years ago
9
Basic Schematic Question

#22 singh577 closed 7 years ago
1
Is it possible to use a ON/OFF switch with 2 positions?

#21 propergol closed 7 years ago
2
Auto Power on

#20 LordBrain closed 7 years ago
9
100K resistor?

#19 maxeph closed 7 years ago
1
Incompatible with RedBear IoT pHAT?

#18 drewcovi closed 7 years ago
8
Need to use serial to connect pc to Pi

#17 PunyViking closed 7 years ago
6
Shutting straight down

#16 urban2015 closed 7 years ago
42
Power Up path in the Power Up / Power Down version will pull GPIO 14 above 3.3 volts

#15 cgri closed 7 years ago
1
Auto Power On?

#14 desmando closed 8 years ago
1
Power up/power down version

#13 Klonx closed 7 years ago
1
can't see the button in the photo

#12 The-Alchemist closed 8 years ago
3
Fix small typo ('batter')

#11 The-Alchemist closed 8 years ago
0
fixed tiny typo

#10 The-Alchemist closed 8 years ago
0
not enough voltage on GPIO14 on pi3

#9 macsimski closed 8 years ago
20