search

Ysurac / openmptcprouter

OpenMPTCProuter is an open source solution to aggregate multiple internet connections using Multipath TCP (MPTCP) on OpenWrt
https://www.openmptcprouter.com/
GNU General Public License v3.0
1.92k stars 274 forks source link

Redémarrages/plantages du routeur #1541

Closed mathchab closed 3 years ago

mathchab commented 3 years ago

Excpectations

Fonctionnement en continu du routeur.

Current Behavior

Le routeur plante dans les 10 minutes qui suivent l’allumage. La configuration semble OK, l’accès internet est OK, les 2 WAN sont connectées.

J’ai tenté tous les VPN. Avec ou sans WAN. Clean install (reformatage SD). RPi différent. Autre version de l’archive. Autre alimentation. Je n’ai rien en USB.

Cela se produit depuis un matin, sans que la config physique comme logicielle n’ai été modifiée.

Merci de m’indiquer la démarche pour vous fournir un log...

Merci de votre aide.

Specifications

Ysurac commented 3 years ago

Les logs sont dans Etat->Journal système et journal noyau.

mathchab commented 3 years ago

Les logs sont dans Etat->Journal système et journal noyau.

Ils ne sont pas remis à zéro au reboot ? Donc perdu après plantage ? En gros j’attends qu’il plante et au redémarrage je vous copie/colle les 2 pages ?

Merci

Ysurac commented 3 years ago

Dans Système->Système, onglet journalisation, le log peut être enregistré sur le disque. Et non on me colle pas les 2 pages, on lit les logs sachant que si il y a quelque chose ça a des chances d'être vers l'heure du plantage.

mathchab commented 3 years ago

Les voici.

System : Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: service stopped (unbound 1.13.0). Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: server stats for thread 0: 76 queries, 13 answers from cache, 63 recursions, 0 prefetch, 0 rejected by ip ratelimiting Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: server stats for thread 0: requestlist max 23 avg 10.1587 exceeded 0 jostled 0 Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: average recursion processing time 0.298767 sec Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: histogram of recursion processing times Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: [25%]=0.111177 median[50%]=0.219738 [75%]=0.454071 Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: lower(secs) upper(secs) recursions Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: 0.016384 0.032768 1 Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: 0.032768 0.065536 5 Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: 0.065536 0.131072 14 Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: 0.131072 0.262144 17 Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: 0.262144 0.524288 14 Mon Jan 25 20:52:39 2021 daemon.info unbound: [6323:0] info: 0.524288 1.000000 12 Mon Jan 25 20:52:39 2021 daemon.notice unbound: [15415:0] notice: init module 0: iterator Mon Jan 25 20:52:40 2021 daemon.info unbound: [15415:0] info: start of service (unbound 1.13.0). Mon Jan 25 20:52:40 2021 daemon.info vnstatd[4242]: Error: Exec step failed (8: attempt to write a readonly database): "insert or ignore into fiveminute (interface, date, rx, tx) values (2, datetime(datetime(1611527700, 'unixepoch'), ('-' || (strftime('%M', datetime(1611527700, 'unixepoch'))) || ' minutes'), ('-' || (strftime('%S', datetime(1611527700, 'unixepoch'))) || ' seconds'), ('+' || (round(strftime('%M', datetime(1611527700, 'unixepoch'))/5,0)*5) || ' minutes'), 'localtime'), 0, 0)" Mon Jan 25 20:52:40 2021 daemon.info vnstatd[4242]: Error: Fatal database error detected, exiting. Mon Jan 25 20:52:42 2021 user.notice omr-bypass: Reload dnsmasq... Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[13254]: exiting on receipt of SIGTERM Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: started, version 2.82 cachesize 150 Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: DNS service limited to local subnets Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP conntrack ipset auth DNSSEC no-ID loop-detect inotify dumpfile Mon Jan 25 20:52:42 2021 daemon.info dnsmasq-dhcp[16402]: DHCP, IP range 192.168.100.100 -- 192.168.100.249, lease time 12h Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain test Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain onion Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain localhost Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain local Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain invalid Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain bind Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using nameserver 127.0.0.1#5353 Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain use-application-dns.net Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: using only locally-known addresses for domain lan Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: read /etc/hosts - 4 addresses Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: read /tmp/hosts/dhcp.cfg01411c - 15 addresses Mon Jan 25 20:52:42 2021 daemon.info dnsmasq-dhcp[16402]: read /etc/ethers - 0 addresses Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: read /etc/hosts - 4 addresses Mon Jan 25 20:52:42 2021 daemon.info dnsmasq[16402]: read /tmp/hosts/dhcp.cfg01411c - 15 addresses Mon Jan 25 20:52:42 2021 daemon.info dnsmasq-dhcp[16402]: read /etc/ethers - 0 addresses Mon Jan 25 20:52:42 2021 user.notice omr-bypass: OMR-ByPass is running Mon Jan 25 20:52:43 2021 user.notice post-tracking-post-tracking: Check API configuration... Done Mon Jan 25 20:52:43 2021 user.notice post-tracking-post-tracking: Can't find Shadowsocks, restart it... Mon Jan 25 20:52:43 2021 user.notice Shadowsocks: Rules DOWN Mon Jan 25 20:52:44 2021 daemon.err omr-tracker[11159]: Command failed: Not found Mon Jan 25 20:52:44 2021 user.notice omr-bypass: Restart dnsmasq... Mon Jan 25 20:52:44 2021 daemon.info dnsmasq[16402]: exiting on receipt of SIGTERM Mon Jan 25 20:52:45 2021 user.notice Shadowsocks: Rules UP Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: started, version 2.82 cachesize 150 Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: DNS service limited to local subnets Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP conntrack ipset auth DNSSEC no-ID loop-detect inotify dumpfile Mon Jan 25 20:52:45 2021 daemon.info dnsmasq-dhcp[17409]: DHCP, IP range 192.168.100.100 -- 192.168.100.249, lease time 12h Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain test Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain onion Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain localhost Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain local Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain invalid Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain bind Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using nameserver 127.0.0.1#5353 Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain use-application-dns.net Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: using only locally-known addresses for domain lan Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: read /etc/hosts - 4 addresses Mon Jan 25 20:52:45 2021 daemon.info dnsmasq[17409]: read /tmp/hosts/dhcp.cfg01411c - 15 addresses Mon Jan 25 20:52:45 2021 daemon.info dnsmasq-dhcp[17409]: read /etc/ethers - 0 addresses Mon Jan 25 20:52:45 2021 user.notice omr-bypass: OMR-ByPass is running Mon Jan 25 20:52:45 2021 daemon.err omr-tracker[11159]: Flush terminated Mon Jan 25 20:52:45 2021 cron.err crond[2861]: time disparity of 1276 minutes detected Mon Jan 25 20:52:45 2021 user.notice Shadowsocks: Reload omr-bypass rules Mon Jan 25 20:52:45 2021 user.notice omr-bypass: Starting OMR-ByPass... Mon Jan 25 20:52:45 2021 daemon.info vnstatd[17525]: Info: vnStat daemon 2.6 started. (pid:17525 uid:0 gid:0 64-bit) Mon Jan 25 20:52:45 2021 daemon.info vnstatd[17525]: Info: Monitoring (8): wlan0 (1000 Mbit) wan2 (1000 Mbit) wan1 (1000 Mbit) tun0 (10 Mbit) teql0 (1000 Mbit) ifb1 (1000 Mbit) ifb0 (1000 Mbit) eth0 (1000 Mbit) Mon Jan 25 20:52:45 2021 daemon.info vnstatd[17525]: Info: Interface "ifb1" disabled. Mon Jan 25 20:52:45 2021 daemon.info vnstatd[17525]: Info: Interface "ifb0" disabled. Mon Jan 25 20:52:45 2021 daemon.info vnstatd[17525]: Info: Removing interface "ifb1" from database as it is disabled and has seen no data. Mon Jan 25 20:52:45 2021 daemon.info vnstatd[17525]: Info: Removing interface "ifb1" from update list. Mon Jan 25 20:52:45 2021 daemon.info vnstatd[17525]: Info: Monitoring (7): wlan0 (1000 Mbit) wan2 (1000 Mbit) wan1 (1000 Mbit) tun0 (10 Mbit) teql0 (1000 Mbit) ifb0 (1000 Mbit) eth0 (1000 Mbit) Mon Jan 25 20:52:47 2021 daemon.notice procd: /etc/rc.d/S99openmptcprouter-vps: {"result":"done","reason":"no changes","route":"shadowsocks"} Mon Jan 25 20:52:49 2021 user.notice omr-bypass: Reload dnsmasq... Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[17409]: exiting on receipt of SIGTERM Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: started, version 2.82 cachesize 150 Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: DNS service limited to local subnets Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP conntrack ipset auth DNSSEC no-ID loop-detect inotify dumpfile Mon Jan 25 20:52:49 2021 daemon.info dnsmasq-dhcp[18785]: DHCP, IP range 192.168.100.100 -- 192.168.100.249, lease time 12h Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain test Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain onion Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain localhost Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain local Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain invalid Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain bind Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using nameserver 127.0.0.1#5353 Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain use-application-dns.net Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: using only locally-known addresses for domain lan Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: read /etc/hosts - 4 addresses Mon Jan 25 20:52:49 2021 daemon.info dnsmasq[18785]: read /tmp/hosts/dhcp.cfg01411c - 15 addresses Mon Jan 25 20:52:49 2021 daemon.info dnsmasq-dhcp[18785]: read /etc/ethers - 0 addresses Mon Jan 25 20:52:49 2021 user.notice omr-bypass: OMR-ByPass is running Mon Jan 25 20:52:50 2021 user.info : using tcp fast open Mon Jan 25 20:52:50 2021 user.info : using tcp fast open Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18854]: resolving hostname to IPv6 address first Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18854]: initializing ciphers... chacha20-ietf-poly1305 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18856]: initializing ciphers... chacha20-ietf-poly1305 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18854]: listening at 0.0.0.0:1100 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18856]: listening at 0.0.0.0:1100 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18854]: tcp port reuse enabled Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18856]: tcp port reuse enabled Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18854]: UDP relay enabled Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18856]: UDP relay enabled Mon Jan 25 20:52:50 2021 daemon.err /usr/bin/ss-redir[18856]: [udp] getaddrinfo: System error Mon Jan 25 20:52:50 2021 daemon.err /usr/bin/ss-redir[18854]: [udp] getaddrinfo: System error Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18854]: running from root user Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18856]: running from root user Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-local[18852]: using tcp fast open Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-local[18852]: initializing ciphers... chacha20-ietf-poly1305 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-local[18852]: listening at 127.0.0.1:1111 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-local[18852]: tcp port reuse enabled Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-local[18852]: udprelay enabled Mon Jan 25 20:52:50 2021 user.info : using tcp fast open Mon Jan 25 20:52:50 2021 daemon.err /usr/bin/ss-local[18852]: [udp] getaddrinfo: System error Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-local[18852]: running from root user Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18855]: initializing ciphers... chacha20-ietf-poly1305 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18855]: listening at 0.0.0.0:1100 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18855]: tcp port reuse enabled Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18855]: UDP relay enabled Mon Jan 25 20:52:50 2021 daemon.err /usr/bin/ss-redir[18855]: [udp] getaddrinfo: System error Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18855]: running from root user Mon Jan 25 20:52:50 2021 user.info : using tcp fast open Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18853]: resolving hostname to IPv6 address first Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18853]: initializing ciphers... chacha20-ietf-poly1305 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18853]: listening at 0.0.0.0:1100 Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18853]: tcp port reuse enabled Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18853]: UDP relay enabled Mon Jan 25 20:52:50 2021 daemon.err /usr/bin/ss-redir[18853]: [udp] getaddrinfo: System error Mon Jan 25 20:52:50 2021 daemon.info /usr/bin/ss-redir[18853]: running from root user Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: ttyd 1.6.1 (libwebsockets 3.1.0) Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: tty configuration: Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: start command: /usr/libexec/login.sh Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: close signal: SIGHUP (1) Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: terminal type: xterm-256color Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: Using foreign event loop... Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: Creating Vhost 'default' port 7681, 2 protocols, IPv6 off Mon Jan 25 20:52:52 2021 daemon.notice ttyd[19128]: Listening on port: 7681 Mon Jan 25 20:52:52 2021 daemon.notice procd: /etc/rc.d/S99v2ray: Flush terminated Mon Jan 25 20:52:52 2021 daemon.info procd: - init complete - Mon Jan 25 20:52:59 2021 user.notice MPTCP: Add route :: via fe80::a00:1 dev Mon Jan 25 20:52:59 2021 daemon.info omr-tracker-ss: Shadowsocks is up (can contact via http 104.16.1.1) Mon Jan 25 20:52:59 2021 user.notice mptcp: Reloading mptcp config due to ifup of loopback (lo) Mon Jan 25 20:53:00 2021 user.notice MPTCP: Add route :: via fe80::a00:1 dev Mon Jan 25 20:53:01 2021 user.notice SQM: Starting SQM script: simple.qos on tun0, in: 0 Kbps, out: 0 Kbps Mon Jan 25 20:53:01 2021 user.notice SQM: Using generic sqm_start_default function. Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: add network interface TMP_IFB_4_SQM: event processed Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: event reported: action=add, name=TMP_IFB_4_SQM, subsystem=net Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: error: parent device sysfspath not found Mon Jan 25 20:53:01 2021 daemon.warn [4336]: [TMP_IFB_4_SQM] invalid sysfs path read for net/TMP_IFB_4_SQM Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: remove network interface TMP_IFB_4_SQM: event processed Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: event reported: action=remove, name=TMP_IFB_4_SQM, subsystem=net Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: add network interface TMP_IFB_4_SQM: event processed Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: event reported: action=add, name=TMP_IFB_4_SQM, subsystem=net Mon Jan 25 20:53:01 2021 user.notice ModemManager: hotplug: error: parent device sysfspath not found Mon Jan 25 20:53:01 2021 daemon.warn [4336]: [TMP_IFB_4_SQM] invalid sysfs path read for net/TMP_IFB_4_SQM Mon Jan 25 20:53:02 2021 user.notice ModemManager: hotplug: remove network interface TMP_IFB_4_SQM: event processed Mon Jan 25 20:53:02 2021 user.notice ModemManager: hotplug: event reported: action=remove, name=TMP_IFB_4_SQM, subsystem=net Mon Jan 25 20:53:02 2021 user.notice SQM: simple.qos was started on tun0 successfully Mon Jan 25 20:53:02 2021 user.notice ModemManager: hotplug: add network interface ifb4tun0: event processed Mon Jan 25 20:53:02 2021 user.notice ModemManager: hotplug: event reported: action=add, name=ifb4tun0, subsystem=net Mon Jan 25 20:53:02 2021 user.notice ModemManager: hotplug: error: parent device sysfspath not found Mon Jan 25 20:53:02 2021 user.notice firewall: Reloading firewall due to ifup of omrvpn (tun0) Mon Jan 25 20:53:02 2021 user.notice omr-bypass: Starting OMR-ByPass... Mon Jan 25 20:53:06 2021 user.notice omr-bypass: Reload dnsmasq... Mon Jan 25 20:53:07 2021 daemon.info dnsmasq[18785]: read /etc/hosts - 4 addresses Mon Jan 25 20:53:07 2021 daemon.info dnsmasq[18785]: read /tmp/hosts/dhcp.cfg01411c - 15 addresses Mon Jan 25 20:53:07 2021 daemon.info dnsmasq-dhcp[18785]: read /etc/ethers - 0 addresses Mon Jan 25 20:53:07 2021 user.notice omr-bypass: OMR-ByPass is running Mon Jan 25 20:53:07 2021 daemon.debug dnsmasq[18785]: listening on tun0(#20): 10.255.254.2 port 53 Mon Jan 25 20:53:07 2021 user.notice mptcp: Reloading mptcp config due to ifup of omrvpn (tun0) Mon Jan 25 20:53:13 2021 user.info : using tcp fast open Mon Jan 25 20:53:13 2021 daemon.info /usr/bin/ss-redir[22288]: initializing ciphers... chacha20-ietf-poly1305 Mon Jan 25 20:53:13 2021 daemon.info /usr/bin/ss-redir[22288]: listening at 0.0.0.0:1100 Mon Jan 25 20:53:13 2021 daemon.info /usr/bin/ss-redir[22288]: tcp port reuse enabled Mon Jan 25 20:53:13 2021 daemon.info /usr/bin/ss-redir[22288]: UDP relay enabled Mon Jan 25 20:53:13 2021 daemon.err /usr/bin/ss-redir[22288]: [udp] getaddrinfo: System error Mon Jan 25 20:53:13 2021 daemon.info /usr/bin/ss-redir[22288]: running from root user Mon Jan 25 20:53:23 2021 user.notice MPTCP: Add route :: via fe80::a00:1 dev Mon Jan 25 20:53:30 2021 daemon.err uhttpd[3350]: luci: accepted login on /admin/status/syslog for root from 192.168.100.146

Noyau :

[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.83 (runner@fv-az76-868) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r0+15225-bfc433efd4)) #0 SMP Tue Dec 15 19:35:00 2020 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=30c5383d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Plus Rev 1.3 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000037400000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] On node 0 totalpages: 242688 [ 0.000000] DMA zone: 2304 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 46080 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 15 pages/cpu s30860 r8192 d22388 u61440 [ 0.000000] pcpu-alloc: s30860 r8192 d22388 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240384 [ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x2aff8000-0x2eff8000] (64MB) [ 0.000000] Memory: 813828K/970752K available (6416K kernel code, 232K rwdata, 1688K rodata, 2048K init, 400K bss, 91388K reserved, 65536K cma-reserved, 118784K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x2fc/0x430 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000020] Switching to timer-based delay loop, resolution 52ns [ 0.000186] Console: colour dummy device 80x30 [ 0.000616] printk: console [tty1] enabled [ 0.000664] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000699] pid_max: default: 32768 minimum: 301 [ 0.000892] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.000926] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001798] Disabling memory control group subsystem [ 0.001841] CPU: Testing write buffer coherency: ok [ 0.002208] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002686] Setting up static identity map for 0x200000 - 0x200060 [ 0.002795] rcu: Hierarchical SRCU implementation. [ 0.003148] smp: Bringing up secondary CPUs ... [ 0.003814] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.004642] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.005364] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.005510] smp: Brought up 1 node, 4 CPUs [ 0.005575] SMP: Total of 4 processors activated (153.60 BogoMIPS). [ 0.005594] CPU: All CPU(s) started in HYP mode. [ 0.005609] CPU: Virtualization extensions available. [ 0.006202] devtmpfs: initialized [ 0.016642] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4 [ 0.016882] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016923] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.019442] pinctrl core: initialized pinctrl subsystem [ 0.019824] reg-dummy reg-dummy: no of_node; not parsing pinctrl DT [ 0.020591] NET: Registered protocol family 16 [ 0.023102] DMA: preallocated 1024 KiB pool for atomic coherent allocations [ 0.027003] cpuidle: using governor ladder [ 0.027043] cpuidle: using governor menu [ 0.027627] Serial: AMBA PL011 UART driver [ 0.028695] bcm2835-mbox 3f00b880.mailbox: mailbox enabled [ 0.050035] raspberrypi-firmware soc:firmware: Attached to firmware from 2020-04-15 11:43, variant start [ 0.060041] raspberrypi-firmware soc:firmware: Firmware hash is 82f9bb929ce2186eb1824178c1ae82902ad6275c [ 0.095600] bcm2835-dma 3f007000.dma: DMA legacy API manager, dmachans=0x1 [ 0.096641] reg-fixed-voltage fixedregulator_3v3: GPIO lookup for consumer (null) [ 0.096650] reg-fixed-voltage fixedregulator_3v3: using device tree for GPIO lookup [ 0.096669] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/fixedregulator_3v3[0]' [ 0.096686] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator_3v3[0]' [ 0.096697] reg-fixed-voltage fixedregulator_3v3: using lookup tables for GPIO lookup [ 0.096705] reg-fixed-voltage fixedregulator_3v3: No GPIO consumer (null) found [ 0.096951] reg-fixed-voltage fixedregulator_5v0: GPIO lookup for consumer (null) [ 0.096959] reg-fixed-voltage fixedregulator_5v0: using device tree for GPIO lookup [ 0.096976] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/fixedregulator_5v0[0]' [ 0.096992] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator_5v0[0]' [ 0.097002] reg-fixed-voltage fixedregulator_5v0: using lookup tables for GPIO lookup [ 0.097010] reg-fixed-voltage fixedregulator_5v0: No GPIO consumer (null) found [ 0.097622] SCSI subsystem initialized [ 0.097823] usbcore: registered new interface driver usbfs [ 0.097887] usbcore: registered new interface driver hub [ 0.097957] usbcore: registered new device driver usb [ 0.098190] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.099428] clocksource: Switched to clocksource arch_sys_counter [ 0.106864] thermal_sys: Registered thermal governor 'step_wise' [ 0.107165] NET: Registered protocol family 2 [ 0.107986] MPTCP tokens hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.108068] MPTCP request tokens hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.108193] default registered [ 0.108209] default registered [ 0.108222] MPTCP: Unstable branch [ 0.108241] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.108308] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.108436] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.108635] TCP: Hash tables configured (established 8192 bind 8192) [ 0.108775] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.108835] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.109061] NET: Registered protocol family 1 [ 0.109107] PCI: CLS 0 bytes, default 64 [ 0.110518] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 0.117270] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.166335] bounce: pool size: 64 pages [ 0.166386] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.167053] pinctrl-bcm2835 3f200000.gpio: try to register 54 pins ... [ 0.167062] pinctrl core: registered pin 0 (gpio0) on pinctrl-bcm2835 [ 0.167069] pinctrl core: registered pin 1 (gpio1) on pinctrl-bcm2835 [ 0.167075] pinctrl core: registered pin 2 (gpio2) on pinctrl-bcm2835 [ 0.167081] pinctrl core: registered pin 3 (gpio3) on pinctrl-bcm2835 [ 0.167087] pinctrl core: registered pin 4 (gpio4) on pinctrl-bcm2835 [ 0.167093] pinctrl core: registered pin 5 (gpio5) on pinctrl-bcm2835 [ 0.167098] pinctrl core: registered pin 6 (gpio6) on pinctrl-bcm2835 [ 0.167103] pinctrl core: registered pin 7 (gpio7) on pinctrl-bcm2835 [ 0.167108] pinctrl core: registered pin 8 (gpio8) on pinctrl-bcm2835 [ 0.167118] pinctrl core: registered pin 9 (gpio9) on pinctrl-bcm2835 [ 0.167124] pinctrl core: registered pin 10 (gpio10) on pinctrl-bcm2835 [ 0.167129] pinctrl core: registered pin 11 (gpio11) on pinctrl-bcm2835 [ 0.167135] pinctrl core: registered pin 12 (gpio12) on pinctrl-bcm2835 [ 0.167140] pinctrl core: registered pin 13 (gpio13) on pinctrl-bcm2835 [ 0.167145] pinctrl core: registered pin 14 (gpio14) on pinctrl-bcm2835 [ 0.167151] pinctrl core: registered pin 15 (gpio15) on pinctrl-bcm2835 [ 0.167156] pinctrl core: registered pin 16 (gpio16) on pinctrl-bcm2835 [ 0.167161] pinctrl core: registered pin 17 (gpio17) on pinctrl-bcm2835 [ 0.167167] pinctrl core: registered pin 18 (gpio18) on pinctrl-bcm2835 [ 0.167172] pinctrl core: registered pin 19 (gpio19) on pinctrl-bcm2835 [ 0.167177] pinctrl core: registered pin 20 (gpio20) on pinctrl-bcm2835 [ 0.167183] pinctrl core: registered pin 21 (gpio21) on pinctrl-bcm2835 [ 0.167188] pinctrl core: registered pin 22 (gpio22) on pinctrl-bcm2835 [ 0.167194] pinctrl core: registered pin 23 (gpio23) on pinctrl-bcm2835 [ 0.167199] pinctrl core: registered pin 24 (gpio24) on pinctrl-bcm2835 [ 0.167204] pinctrl core: registered pin 25 (gpio25) on pinctrl-bcm2835 [ 0.167210] pinctrl core: registered pin 26 (gpio26) on pinctrl-bcm2835 [ 0.167215] pinctrl core: registered pin 27 (gpio27) on pinctrl-bcm2835 [ 0.167220] pinctrl core: registered pin 28 (gpio28) on pinctrl-bcm2835 [ 0.167226] pinctrl core: registered pin 29 (gpio29) on pinctrl-bcm2835 [ 0.167231] pinctrl core: registered pin 30 (gpio30) on pinctrl-bcm2835 [ 0.167236] pinctrl core: registered pin 31 (gpio31) on pinctrl-bcm2835 [ 0.167242] pinctrl core: registered pin 32 (gpio32) on pinctrl-bcm2835 [ 0.167247] pinctrl core: registered pin 33 (gpio33) on pinctrl-bcm2835 [ 0.167252] pinctrl core: registered pin 34 (gpio34) on pinctrl-bcm2835 [ 0.167258] pinctrl core: registered pin 35 (gpio35) on pinctrl-bcm2835 [ 0.167263] pinctrl core: registered pin 36 (gpio36) on pinctrl-bcm2835 [ 0.167269] pinctrl core: registered pin 37 (gpio37) on pinctrl-bcm2835 [ 0.167274] pinctrl core: registered pin 38 (gpio38) on pinctrl-bcm2835 [ 0.167279] pinctrl core: registered pin 39 (gpio39) on pinctrl-bcm2835 [ 0.167284] pinctrl core: registered pin 40 (gpio40) on pinctrl-bcm2835 [ 0.167289] pinctrl core: registered pin 41 (gpio41) on pinctrl-bcm2835 [ 0.167295] pinctrl core: registered pin 42 (gpio42) on pinctrl-bcm2835 [ 0.167300] pinctrl core: registered pin 43 (gpio43) on pinctrl-bcm2835 [ 0.167305] pinctrl core: registered pin 44 (gpio44) on pinctrl-bcm2835 [ 0.167311] pinctrl core: registered pin 45 (gpio45) on pinctrl-bcm2835 [ 0.167316] pinctrl core: registered pin 46 (gpio46) on pinctrl-bcm2835 [ 0.167321] pinctrl core: registered pin 47 (gpio47) on pinctrl-bcm2835 [ 0.167327] pinctrl core: registered pin 48 (gpio48) on pinctrl-bcm2835 [ 0.167332] pinctrl core: registered pin 49 (gpio49) on pinctrl-bcm2835 [ 0.167337] pinctrl core: registered pin 50 (gpio50) on pinctrl-bcm2835 [ 0.167342] pinctrl core: registered pin 51 (gpio51) on pinctrl-bcm2835 [ 0.167348] pinctrl core: registered pin 52 (gpio52) on pinctrl-bcm2835 [ 0.167353] pinctrl core: registered pin 53 (gpio53) on pinctrl-bcm2835 [ 0.167365] pinctrl-bcm2835 3f200000.gpio: no hogs found [ 0.167523] pinctrl-bcm2835 3f200000.gpio: get 00000000 (0 => gpio_in) [ 0.167533] pinctrl-bcm2835 3f200000.gpio: get 00000000 (1 => gpio_in) [ 0.167543] pinctrl-bcm2835 3f200000.gpio: get 00000000 (2 => gpio_in) [ 0.167552] pinctrl-bcm2835 3f200000.gpio: get 00000000 (3 => gpio_in) [ 0.167561] pinctrl-bcm2835 3f200000.gpio: get 00000000 (4 => gpio_in) [ 0.167570] pinctrl-bcm2835 3f200000.gpio: get 00000000 (5 => gpio_in) [ 0.167580] pinctrl-bcm2835 3f200000.gpio: get 00000000 (6 => gpio_in) [ 0.167589] pinctrl-bcm2835 3f200000.gpio: get 00000000 (7 => gpio_in) [ 0.167598] pinctrl-bcm2835 3f200000.gpio: get 00000000 (8 => gpio_in) [ 0.167607] pinctrl-bcm2835 3f200000.gpio: get 00000000 (9 => gpio_in) [ 0.167617] pinctrl-bcm2835 3f200000.gpio: get 00024000 (10 => gpio_in) [ 0.167627] pinctrl-bcm2835 3f200000.gpio: get 00024000 (11 => gpio_in) [ 0.167637] pinctrl-bcm2835 3f200000.gpio: get 00024000 (12 => gpio_in) [ 0.167646] pinctrl-bcm2835 3f200000.gpio: get 00024000 (13 => gpio_in) [ 0.167656] pinctrl-bcm2835 3f200000.gpio: get 00024000 (14 => alt0) [ 0.167665] pinctrl-bcm2835 3f200000.gpio: get 00024000 (15 => alt0) [ 0.167675] pinctrl-bcm2835 3f200000.gpio: get 00024000 (16 => gpio_in) [ 0.167684] pinctrl-bcm2835 3f200000.gpio: get 00024000 (17 => gpio_in) [ 0.167693] pinctrl-bcm2835 3f200000.gpio: get 00024000 (18 => gpio_in) [ 0.167703] pinctrl-bcm2835 3f200000.gpio: get 00024000 (19 => gpio_in) [ 0.167712] pinctrl-bcm2835 3f200000.gpio: get 08000000 (20 => gpio_in) [ 0.167722] pinctrl-bcm2835 3f200000.gpio: get 08000000 (21 => gpio_in) [ 0.167732] pinctrl-bcm2835 3f200000.gpio: get 08000000 (22 => gpio_in) [ 0.167741] pinctrl-bcm2835 3f200000.gpio: get 08000000 (23 => gpio_in) [ 0.167751] pinctrl-bcm2835 3f200000.gpio: get 08000000 (24 => gpio_in) [ 0.167760] pinctrl-bcm2835 3f200000.gpio: get 08000000 (25 => gpio_in) [ 0.167769] pinctrl-bcm2835 3f200000.gpio: get 08000000 (26 => gpio_in) [ 0.167779] pinctrl-bcm2835 3f200000.gpio: get 08000000 (27 => gpio_in) [ 0.167788] pinctrl-bcm2835 3f200000.gpio: get 08000000 (28 => gpio_in) [ 0.167797] pinctrl-bcm2835 3f200000.gpio: get 08000000 (29 => gpio_out) [ 0.167807] pinctrl-bcm2835 3f200000.gpio: get 00000009 (30 => gpio_out) [ 0.167816] pinctrl-bcm2835 3f200000.gpio: get 00000009 (31 => gpio_out) [ 0.167825] pinctrl-bcm2835 3f200000.gpio: get 00000009 (32 => gpio_in) [ 0.167835] pinctrl-bcm2835 3f200000.gpio: get 00000009 (33 => gpio_in) [ 0.167844] pinctrl-bcm2835 3f200000.gpio: get 00000009 (34 => gpio_in) [ 0.167853] pinctrl-bcm2835 3f200000.gpio: get 00000009 (35 => gpio_in) [ 0.167862] pinctrl-bcm2835 3f200000.gpio: get 00000009 (36 => gpio_in) [ 0.167871] pinctrl-bcm2835 3f200000.gpio: get 00000009 (37 => gpio_in) [ 0.167880] pinctrl-bcm2835 3f200000.gpio: get 00000009 (38 => gpio_in) [ 0.167890] pinctrl-bcm2835 3f200000.gpio: get 00000009 (39 => gpio_in) [ 0.167899] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (40 => alt0) [ 0.167909] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (41 => alt0) [ 0.167918] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (42 => alt0) [ 0.167927] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (43 => alt0) [ 0.167937] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (44 => gpio_in) [ 0.167946] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (45 => gpio_in) [ 0.167956] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (46 => gpio_in) [ 0.167966] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (47 => gpio_out) [ 0.167975] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (48 => alt3) [ 0.167984] pinctrl-bcm2835 3f200000.gpio: get 3f200924 (49 => alt3) [ 0.167994] pinctrl-bcm2835 3f200000.gpio: get 00000fff (50 => alt3) [ 0.168003] pinctrl-bcm2835 3f200000.gpio: get 00000fff (51 => alt3) [ 0.168012] pinctrl-bcm2835 3f200000.gpio: get 00000fff (52 => alt3) [ 0.168021] pinctrl-bcm2835 3f200000.gpio: get 00000fff (53 => alt3) [ 0.168191] gpio gpiochip0: (pinctrl-bcm2835): added GPIO chardev (254:0) [ 0.168199] gpiochip_setup_dev: registered GPIOs 0 to 53 on device: gpiochip0 (pinctrl-bcm2835) [ 0.168507] gpiochip_find_base: found new base at 504 [ 0.203661] gpio gpiochip1: (raspberrypi-exp-gpio): added GPIO chardev (254:1) [ 0.203669] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (raspberrypi-exp-gpio) [ 0.208555] bcm2708_fb soc:fb: FB found 1 display(s) [ 0.252256] Console: switching to colour frame buffer device 82x26 [ 0.264426] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 656x416 [ 0.289495] raspberrypi-clk firmware-clocks: CPU frequency range: min 600000000, max 1400000000 [ 0.334903] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled [ 0.337674] serial8250 serial8250: no of_node; not parsing pinctrl DT [ 0.338417] bcm2835-rng 3f104000.rng: hwrng registered [ 0.341002] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB) [ 0.346185] vc-sm: Videocore shared memory driver [ 0.348828] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000 [ 0.362274] brd: module loaded [ 0.369261] loop: module loaded [ 0.372020] bcm2835-power bcm2835-power: no of_node; not parsing pinctrl DT [ 0.372493] Loading iSCSI transport class v2.0-870. [ 0.376351] mdio_bus fixed-0: GPIO lookup for consumer reset [ 0.376359] mdio_bus fixed-0: using lookup tables for GPIO lookup [ 0.376368] mdio_bus fixed-0: No GPIO consumer reset found [ 0.376395] libphy: Fixed MDIO Bus: probed [ 0.378890] usbcore: registered new interface driver lan78xx [ 0.381285] usbcore: registered new interface driver smsc95xx [ 0.383765] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ 0.613854] Core Release: 2.80a [ 0.615989] Setting default values for core params [ 0.618141] Finished setting default values for core params [ 0.820496] Using Buffer DMA mode [ 0.822541] Periodic Transfer Interrupt Enhancement - disabled [ 0.824592] Multiprocessor Interrupt Enhancement - disabled [ 0.826595] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 0.828547] Dedicated Tx FIFOs mode [ 0.830740] WARN::dwc_otg_hcd_init:1072: FIQ DMA bounce buffers: virt = f0bf3000 dma = 0x00000000f7514000 len=9024 [ 0.834598] FIQ FSM acceleration enabled for : [ 0.834598] Non-periodic Split Transactions [ 0.834598] Periodic Split Transactions [ 0.834598] High-Speed Isochronous Endpoints [ 0.834598] Interrupt/Control Split Transaction hack enabled [ 0.843621] dwc_otg: Microframe scheduler enabled [ 0.843669] WARN::hcd_init_fiq:432: FIQ on core 1 [ 0.845497] WARN::hcd_init_fiq:433: FIQ ASM at c0637f9c length 36 [ 0.847332] WARN::hcd_init_fiq:472: MPHI regs_base at f0810000 [ 0.849151] dwc_otg 3f980000.usb: DWC OTG Controller [ 0.851038] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1 [ 0.852959] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000 [ 0.854848] Init: Port Power? op_state=1 [ 0.856676] Init: Power Port (0) [ 0.858652] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 0.862351] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.864327] usb usb1: Product: DWC OTG Controller [ 0.866265] usb usb1: Manufacturer: Linux 5.4.83 dwc_otg_hcd [ 0.868230] usb usb1: SerialNumber: 3f980000.usb [ 0.870638] hub 1-0:1.0: USB hub found [ 0.872490] hub 1-0:1.0: 1 port detected [ 0.874707] dwc_otg: FIQ enabled [ 0.874711] dwc_otg: NAK holdoff enabled [ 0.874715] dwc_otg: FIQ split-transaction FSM enabled [ 0.874723] Module dwc_common_port init [ 0.874981] usbcore: registered new interface driver uas [ 0.876872] usbcore: registered new interface driver usb-storage [ 0.878832] mousedev: PS/2 mouse device common for all mice [ 0.881046] bcm2835-wdt bcm2835-wdt: no of_node; not parsing pinctrl DT [ 0.881286] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer [ 0.883332] raspberrypi-cpufreq raspberrypi-cpufreq: no of_node; not parsing pinctrl DT [ 0.883737] cpufreq-dt cpufreq-dt: no of_node; not parsing pinctrl DT [ 0.883883] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 600000 KHz [ 0.890846] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 700000 KHz [ 0.892665] sdhci: Secure Digital Host Controller Interface driver [ 0.893539] sdhci: Copyright(c) Pierre Ossman [ 0.894436] pinctrl core: add 12 pinctrl maps [ 0.894451] pinctrl-bcm2835 3f200000.gpio: found group selector 34 for gpio34 [ 0.894464] pinctrl-bcm2835 3f200000.gpio: found group selector 35 for gpio35 [ 0.894475] pinctrl-bcm2835 3f200000.gpio: found group selector 36 for gpio36 [ 0.894485] pinctrl-bcm2835 3f200000.gpio: found group selector 37 for gpio37 [ 0.894496] pinctrl-bcm2835 3f200000.gpio: found group selector 38 for gpio38 [ 0.894506] pinctrl-bcm2835 3f200000.gpio: found group selector 39 for gpio39 [ 0.894516] pinctrl-bcm2835 3f200000.gpio: request pin 34 (gpio34) for 3f300000.mmcnr [ 0.894521] pinctrl-bcm2835 3f200000.gpio: read 00000009 (34 => gpio_in) [ 0.894525] pinctrl-bcm2835 3f200000.gpio: write 00007009 (34 <= alt3) [ 0.894533] pinctrl-bcm2835 3f200000.gpio: request pin 35 (gpio35) for 3f300000.mmcnr [ 0.894538] pinctrl-bcm2835 3f200000.gpio: read 00007009 (35 => gpio_in) [ 0.894542] pinctrl-bcm2835 3f200000.gpio: write 0003f009 (35 <= alt3) [ 0.894548] pinctrl-bcm2835 3f200000.gpio: request pin 36 (gpio36) for 3f300000.mmcnr [ 0.894552] pinctrl-bcm2835 3f200000.gpio: read 0003f009 (36 => gpio_in) [ 0.894556] pinctrl-bcm2835 3f200000.gpio: write 001ff009 (36 <= alt3) [ 0.894562] pinctrl-bcm2835 3f200000.gpio: request pin 37 (gpio37) for 3f300000.mmcnr [ 0.894567] pinctrl-bcm2835 3f200000.gpio: read 001ff009 (37 => gpio_in) [ 0.894571] pinctrl-bcm2835 3f200000.gpio: write 00fff009 (37 <= alt3) [ 0.894577] pinctrl-bcm2835 3f200000.gpio: request pin 38 (gpio38) for 3f300000.mmcnr [ 0.894581] pinctrl-bcm2835 3f200000.gpio: read 00fff009 (38 => gpio_in) [ 0.894585] pinctrl-bcm2835 3f200000.gpio: write 07fff009 (38 <= alt3) [ 0.894591] pinctrl-bcm2835 3f200000.gpio: request pin 39 (gpio39) for 3f300000.mmcnr [ 0.894596] pinctrl-bcm2835 3f200000.gpio: read 07fff009 (39 => gpio_in) [ 0.894600] pinctrl-bcm2835 3f200000.gpio: write 3ffff009 (39 <= alt3) [ 0.894672] mmc-bcm2835 3f300000.mmcnr: could not get clk, deferring probe [ 0.895607] pinctrl-bcm2835 3f200000.gpio: read 3ffff009 (34 => alt3) [ 0.895611] pinctrl-bcm2835 3f200000.gpio: write 3fff8009 (34 <= gpio_in) [ 0.895616] pinctrl-bcm2835 3f200000.gpio: read 3fff8009 (35 => alt3) [ 0.895620] pinctrl-bcm2835 3f200000.gpio: write 3ffc0009 (35 <= gpio_in) [ 0.895625] pinctrl-bcm2835 3f200000.gpio: read 3ffc0009 (36 => alt3) [ 0.895628] pinctrl-bcm2835 3f200000.gpio: write 3fe00009 (36 <= gpio_in) [ 0.895633] pinctrl-bcm2835 3f200000.gpio: read 3fe00009 (37 => alt3) [ 0.895637] pinctrl-bcm2835 3f200000.gpio: write 3f000009 (37 <= gpio_in) [ 0.895641] pinctrl-bcm2835 3f200000.gpio: read 3f000009 (38 => alt3) [ 0.895645] pinctrl-bcm2835 3f200000.gpio: write 38000009 (38 <= gpio_in) [ 0.895650] pinctrl-bcm2835 3f200000.gpio: read 38000009 (39 => alt3) [ 0.895654] pinctrl-bcm2835 3f200000.gpio: write 00000009 (39 <= gpio_in) [ 0.895705] pinctrl core: add 6 pinctrl maps [ 0.895715] pinctrl-bcm2835 3f200000.gpio: found group selector 48 for gpio48 [ 0.895724] pinctrl-bcm2835 3f200000.gpio: found group selector 49 for gpio49 [ 0.895731] pinctrl-bcm2835 3f200000.gpio: found group selector 50 for gpio50 [ 0.895739] pinctrl-bcm2835 3f200000.gpio: found group selector 51 for gpio51 [ 0.895747] pinctrl-bcm2835 3f200000.gpio: found group selector 52 for gpio52 [ 0.895755] pinctrl-bcm2835 3f200000.gpio: found group selector 53 for gpio53 [ 0.895760] pinctrl-bcm2835 3f200000.gpio: request pin 48 (gpio48) for 3f202000.mmc [ 0.895765] pinctrl-bcm2835 3f200000.gpio: read 3f200924 (48 => alt3) [ 0.895769] pinctrl-bcm2835 3f200000.gpio: trans 38200924 (48 <= gpio_in) [ 0.895773] pinctrl-bcm2835 3f200000.gpio: write 3c200924 (48 <= alt0) [ 0.895777] pinctrl-bcm2835 3f200000.gpio: request pin 49 (gpio49) for 3f202000.mmc [ 0.895782] pinctrl-bcm2835 3f200000.gpio: read 3c200924 (49 => alt3) [ 0.895786] pinctrl-bcm2835 3f200000.gpio: trans 04200924 (49 <= gpio_in) [ 0.895790] pinctrl-bcm2835 3f200000.gpio: write 24200924 (49 <= alt0) [ 0.895794] pinctrl-bcm2835 3f200000.gpio: request pin 50 (gpio50) for 3f202000.mmc [ 0.895798] pinctrl-bcm2835 3f200000.gpio: read 00000fff (50 => alt3) [ 0.895802] pinctrl-bcm2835 3f200000.gpio: trans 00000ff8 (50 <= gpio_in) [ 0.895806] pinctrl-bcm2835 3f200000.gpio: write 00000ffc (50 <= alt0) [ 0.895811] pinctrl-bcm2835 3f200000.gpio: request pin 51 (gpio51) for 3f202000.mmc [ 0.895815] pinctrl-bcm2835 3f200000.gpio: read 00000ffc (51 => alt3) [ 0.895819] pinctrl-bcm2835 3f200000.gpio: trans 00000fc4 (51 <= gpio_in) [ 0.895823] pinctrl-bcm2835 3f200000.gpio: write 00000fe4 (51 <= alt0) [ 0.895827] pinctrl-bcm2835 3f200000.gpio: request pin 52 (gpio52) for 3f202000.mmc [ 0.895831] pinctrl-bcm2835 3f200000.gpio: read 00000fe4 (52 => alt3) [ 0.895835] pinctrl-bcm2835 3f200000.gpio: trans 00000e24 (52 <= gpio_in) [ 0.895841] pinctrl-bcm2835 3f200000.gpio: write 00000f24 (52 <= alt0) [ 0.895846] pinctrl-bcm2835 3f200000.gpio: request pin 53 (gpio53) for 3f202000.mmc [ 0.895850] pinctrl-bcm2835 3f200000.gpio: read 00000f24 (53 => alt3) [ 0.895854] pinctrl-bcm2835 3f200000.gpio: trans 00000124 (53 <= gpio_in) [ 0.895858] pinctrl-bcm2835 3f200000.gpio: write 00000924 (53 <= alt0) [ 0.895900] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe [ 0.896818] pinctrl-bcm2835 3f200000.gpio: read 24200924 (48 => alt0) [ 0.896822] pinctrl-bcm2835 3f200000.gpio: write 20200924 (48 <= gpio_in) [ 0.896827] pinctrl-bcm2835 3f200000.gpio: read 20200924 (49 => alt0) [ 0.896831] pinctrl-bcm2835 3f200000.gpio: write 00200924 (49 <= gpio_in) [ 0.896835] pinctrl-bcm2835 3f200000.gpio: read 00000924 (50 => alt0) [ 0.896839] pinctrl-bcm2835 3f200000.gpio: write 00000920 (50 <= gpio_in) [ 0.896843] pinctrl-bcm2835 3f200000.gpio: read 00000920 (51 => alt0) [ 0.896847] pinctrl-bcm2835 3f200000.gpio: write 00000900 (51 <= gpio_in) [ 0.896852] pinctrl-bcm2835 3f200000.gpio: read 00000900 (52 => alt0) [ 0.896855] pinctrl-bcm2835 3f200000.gpio: write 00000800 (52 <= gpio_in) [ 0.896860] pinctrl-bcm2835 3f200000.gpio: read 00000800 (53 => alt0) [ 0.896864] pinctrl-bcm2835 3f200000.gpio: write 00000000 (53 <= gpio_in) [ 0.896896] Error: Driver 'sdhost-bcm2835' is already registered, aborting... [ 0.897835] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.898797] pinctrl core: add 12 pinctrl maps [ 0.898807] pinctrl-bcm2835 3f200000.gpio: found group selector 34 for gpio34 [ 0.898819] pinctrl-bcm2835 3f200000.gpio: found group selector 35 for gpio35 [ 0.898829] pinctrl-bcm2835 3f200000.gpio: found group selector 36 for gpio36 [ 0.898840] pinctrl-bcm2835 3f200000.gpio: found group selector 37 for gpio37 [ 0.898851] pinctrl-bcm2835 3f200000.gpio: found group selector 38 for gpio38 [ 0.898862] pinctrl-bcm2835 3f200000.gpio: found group selector 39 for gpio39 [ 0.898870] pinctrl-bcm2835 3f200000.gpio: request pin 34 (gpio34) for 3f300000.mmcnr [ 0.898874] pinctrl-bcm2835 3f200000.gpio: read 00000009 (34 => gpio_in) [ 0.898878] pinctrl-bcm2835 3f200000.gpio: write 00007009 (34 <= alt3) [ 0.898885] pinctrl-bcm2835 3f200000.gpio: request pin 35 (gpio35) for 3f300000.mmcnr [ 0.898889] pinctrl-bcm2835 3f200000.gpio: read 00007009 (35 => gpio_in) [ 0.898893] pinctrl-bcm2835 3f200000.gpio: write 0003f009 (35 <= alt3) [ 0.898899] pinctrl-bcm2835 3f200000.gpio: request pin 36 (gpio36) for 3f300000.mmcnr [ 0.898903] pinctrl-bcm2835 3f200000.gpio: read 0003f009 (36 => gpio_in) [ 0.898907] pinctrl-bcm2835 3f200000.gpio: write 001ff009 (36 <= alt3) [ 0.898914] pinctrl-bcm2835 3f200000.gpio: request pin 37 (gpio37) for 3f300000.mmcnr [ 0.898918] pinctrl-bcm2835 3f200000.gpio: read 001ff009 (37 => gpio_in) [ 0.898922] pinctrl-bcm2835 3f200000.gpio: write 00fff009 (37 <= alt3) [ 0.898928] pinctrl-bcm2835 3f200000.gpio: request pin 38 (gpio38) for 3f300000.mmcnr [ 0.898932] pinctrl-bcm2835 3f200000.gpio: read 00fff009 (38 => gpio_in) [ 0.898936] pinctrl-bcm2835 3f200000.gpio: write 07fff009 (38 <= alt3) [ 0.898942] pinctrl-bcm2835 3f200000.gpio: request pin 39 (gpio39) for 3f300000.mmcnr [ 0.898946] pinctrl-bcm2835 3f200000.gpio: read 07fff009 (39 => gpio_in) [ 0.898950] pinctrl-bcm2835 3f200000.gpio: write 3ffff009 (39 <= alt3) [ 0.898998] sdhci-iproc 3f300000.mmcnr: GPIO lookup for consumer wp [ 0.899002] sdhci-iproc 3f300000.mmcnr: using device tree for GPIO lookup [ 0.899012] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc/mmcnr@7e300000[0]' [ 0.899020] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc/mmcnr@7e300000[0]' [ 0.899025] sdhci-iproc 3f300000.mmcnr: using lookup tables for GPIO lookup [ 0.899029] sdhci-iproc 3f300000.mmcnr: No GPIO consumer wp found [ 0.899058] pinctrl-bcm2835 3f200000.gpio: read 3ffff009 (34 => alt3) [ 0.899063] pinctrl-bcm2835 3f200000.gpio: write 3fff8009 (34 <= gpio_in) [ 0.899067] pinctrl-bcm2835 3f200000.gpio: read 3fff8009 (35 => alt3) [ 0.899071] pinctrl-bcm2835 3f200000.gpio: write 3ffc0009 (35 <= gpio_in) [ 0.899076] pinctrl-bcm2835 3f200000.gpio: read 3ffc0009 (36 => alt3) [ 0.899080] pinctrl-bcm2835 3f200000.gpio: write 3fe00009 (36 <= gpio_in) [ 0.899084] pinctrl-bcm2835 3f200000.gpio: read 3fe00009 (37 => alt3) [ 0.899088] pinctrl-bcm2835 3f200000.gpio: write 3f000009 (37 <= gpio_in) [ 0.899093] pinctrl-bcm2835 3f200000.gpio: read 3f000009 (38 => alt3) [ 0.899097] pinctrl-bcm2835 3f200000.gpio: write 38000009 (38 <= gpio_in) [ 0.899101] pinctrl-bcm2835 3f200000.gpio: read 38000009 (39 => alt3) [ 0.899105] pinctrl-bcm2835 3f200000.gpio: write 00000009 (39 <= gpio_in) [ 0.899186] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/act[0]' - status (0) [ 0.899195] pinctrl-bcm2835 3f200000.gpio: request pin 29 (gpio29) for pinctrl-bcm2835:29 [ 0.899200] pinctrl-bcm2835 3f200000.gpio: get 08000000 (29 => gpio_out) [ 0.899206] gpio gpiochip0: Persistence not supported for GPIO 29 [ 0.899208] no flags found for gpios [ 0.899218] pinctrl-bcm2835 3f200000.gpio: read 08000000 (29 => gpio_out) [ 0.899267] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/pwr[0]' - status (0) [ 0.899294] no flags found for gpios [ 0.914719] vchiq: vchiq_init_state: slot_zero = (ptrval)

[ 0.938415] [vc_sm_connected_init]: end - returning 0 [ 0.940009] NET: Registered protocol family 10 [ 0.941283] Segment Routing with IPv6 [ 0.942173] fullmesh registered [ 0.943003] ndiffports registered [ 0.943839] binder registered [ 0.944670] netlink registered [ 0.945490] roundrobin registered [ 0.946287] redundant registered [ 0.947060] blest registered [ 0.947798] ecf registered [ 0.948520] NET: Registered protocol family 17 [ 0.949242] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.950726] 8021q: 802.1Q VLAN Support v1.8 [ 0.951668] Registering SWP/SWPB emulation handler [ 0.952543] Key type ._fscrypt registered [ 0.953238] Key type .fscrypt registered [ 0.957374] pinctrl core: add 0 pinctrl maps [ 0.957432] uart-pl011 3f201000.serial: cts_event_workaround enabled [ 0.958167] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 81, base_baud = 0) is a PL011 rev2 [ 1.089469] Indeed it is in host mode hprt0 = 00021501 [ 1.092200] printk: console [ttyAMA0] enabled [ 1.299423] usb 1-1: new high-speed USB device number 2 using dwc_otg [ 1.310111] bcm2835-power bcm2835-power: no of_node; not parsing pinctrl DT [ 1.321010] Indeed it is in host mode hprt0 = 00001101 [ 1.328031] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver [ 1.622053] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 1.625603] pinctrl core: add 12 pinctrl maps [ 1.631166] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.641157] hub 1-1:1.0: USB hub found [ 1.644587] pinctrl-bcm2835 3f200000.gpio: found group selector 34 for gpio34 [ 1.688040] hub 1-1:1.0: 4 ports detected [ 1.693874] pinctrl-bcm2835 3f200000.gpio: found group selector 35 for gpio35 [ 2.000709] pinctrl-bcm2835 3f200000.gpio: found group selector 36 for gpio36 [ 2.000735] pinctrl-bcm2835 3f200000.gpio: found group selector 37 for gpio37 [ 2.000761] pinctrl-bcm2835 3f200000.gpio: found group selector 38 for gpio38 [ 2.000786] random: fast init done [ 2.006370] pinctrl-bcm2835 3f200000.gpio: found group selector 39 for gpio39 [ 2.006393] pinctrl-bcm2835 3f200000.gpio: request pin 34 (gpio34) for 3f300000.mmcnr [ 2.006413] pinctrl-bcm2835 3f200000.gpio: read 00000009 (34 => gpio_in) [ 2.006423] pinctrl-bcm2835 3f200000.gpio: write 00007009 (34 <= alt3) [ 2.006437] pinctrl-bcm2835 3f200000.gpio: request pin 35 (gpio35) for 3f300000.mmcnr [ 2.006447] pinctrl-bcm2835 3f200000.gpio: read 00007009 (35 => gpio_in) [ 2.006456] pinctrl-bcm2835 3f200000.gpio: write 0003f009 (35 <= alt3) [ 2.006469] pinctrl-bcm2835 3f200000.gpio: request pin 36 (gpio36) for 3f300000.mmcnr [ 2.006479] pinctrl-bcm2835 3f200000.gpio: read 0003f009 (36 => gpio_in) [ 2.006488] pinctrl-bcm2835 3f200000.gpio: write 001ff009 (36 <= alt3) [ 2.006501] pinctrl-bcm2835 3f200000.gpio: request pin 37 (gpio37) for 3f300000.mmcnr [ 2.006510] pinctrl-bcm2835 3f200000.gpio: read 001ff009 (37 => gpio_in) [ 2.006519] pinctrl-bcm2835 3f200000.gpio: write 00fff009 (37 <= alt3) [ 2.006538] pinctrl-bcm2835 3f200000.gpio: request pin 38 (gpio38) for 3f300000.mmcnr [ 2.006548] pinctrl-bcm2835 3f200000.gpio: read 00fff009 (38 => gpio_in) [ 2.006557] pinctrl-bcm2835 3f200000.gpio: write 07fff009 (38 <= alt3) [ 2.006570] pinctrl-bcm2835 3f200000.gpio: request pin 39 (gpio39) for 3f300000.mmcnr [ 2.006579] pinctrl-bcm2835 3f200000.gpio: read 07fff009 (39 => gpio_in) [ 2.006588] pinctrl-bcm2835 3f200000.gpio: write 3ffff009 (39 <= alt3) [ 2.006768] mmc-bcm2835 3f300000.mmcnr: GPIO lookup for consumer wp [ 2.006777] mmc-bcm2835 3f300000.mmcnr: using device tree for GPIO lookup [ 2.006806] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc/mmcnr@7e300000[0]' [ 2.006823] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc/mmcnr@7e300000[0]' [ 2.006836] mmc-bcm2835 3f300000.mmcnr: using lookup tables for GPIO lookup [ 2.006844] mmc-bcm2835 3f300000.mmcnr: No GPIO consumer wp found [ 2.006888] mmc-bcm2835 3f300000.mmcnr: mmc_debug:0 mmc_debug2:0 [ 2.015117] mmc-bcm2835 3f300000.mmcnr: DMA channel allocated [ 2.048520] pinctrl core: add 6 pinctrl maps [ 2.048552] pinctrl-bcm2835 3f200000.gpio: found group selector 48 for gpio48 [ 2.048572] pinctrl-bcm2835 3f200000.gpio: found group selector 49 for gpio49 [ 2.048590] pinctrl-bcm2835 3f200000.gpio: found group selector 50 for gpio50 [ 2.048609] pinctrl-bcm2835 3f200000.gpio: found group selector 51 for gpio51 [ 2.048627] pinctrl-bcm2835 3f200000.gpio: found group selector 52 for gpio52 [ 2.048646] pinctrl-bcm2835 3f200000.gpio: found group selector 53 for gpio53 [ 2.048660] pinctrl-bcm2835 3f200000.gpio: request pin 48 (gpio48) for 3f202000.mmc [ 2.048671] pinctrl-bcm2835 3f200000.gpio: read 00200924 (48 => gpio_in) [ 2.048680] pinctrl-bcm2835 3f200000.gpio: write 04200924 (48 <= alt0) [ 2.048690] pinctrl-bcm2835 3f200000.gpio: request pin 49 (gpio49) for 3f202000.mmc [ 2.048700] pinctrl-bcm2835 3f200000.gpio: read 04200924 (49 => gpio_in) [ 2.048709] pinctrl-bcm2835 3f200000.gpio: write 24200924 (49 <= alt0) [ 2.048718] pinctrl-bcm2835 3f200000.gpio: request pin 50 (gpio50) for 3f202000.mmc [ 2.048728] pinctrl-bcm2835 3f200000.gpio: read 00000000 (50 => gpio_in) [ 2.048737] pinctrl-bcm2835 3f200000.gpio: write 00000004 (50 <= alt0) [ 2.048747] pinctrl-bcm2835 3f200000.gpio: request pin 51 (gpio51) for 3f202000.mmc [ 2.048756] pinctrl-bcm2835 3f200000.gpio: read 00000004 (51 => gpio_in) [ 2.048765] pinctrl-bcm2835 3f200000.gpio: write 00000024 (51 <= alt0) [ 2.048775] pinctrl-bcm2835 3f200000.gpio: request pin 52 (gpio52) for 3f202000.mmc [ 2.048784] pinctrl-bcm2835 3f200000.gpio: read 00000024 (52 => gpio_in) [ 2.048794] pinctrl-bcm2835 3f200000.gpio: write 00000124 (52 <= alt0) [ 2.048803] pinctrl-bcm2835 3f200000.gpio: request pin 53 (gpio53) for 3f202000.mmc [ 2.048813] pinctrl-bcm2835 3f200000.gpio: read 00000124 (53 => gpio_in) [ 2.048822] pinctrl-bcm2835 3f200000.gpio: write 00000924 (53 <= alt0) [ 2.049024] sdhost: log_buf @ (ptrval) (f7513000) [ 2.055847] sdhost-bcm2835 3f202000.mmc: GPIO lookup for consumer cd [ 2.055856] sdhost-bcm2835 3f202000.mmc: using device tree for GPIO lookup [ 2.055876] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/soc/mmc@7e202000[0]' [ 2.055893] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/soc/mmc@7e202000[0]' [ 2.055907] sdhost-bcm2835 3f202000.mmc: using lookup tables for GPIO lookup [ 2.055915] sdhost-bcm2835 3f202000.mmc: No GPIO consumer cd found [ 2.055925] sdhost-bcm2835 3f202000.mmc: GPIO lookup for consumer wp [ 2.055932] sdhost-bcm2835 3f202000.mmc: using device tree for GPIO lookup [ 2.055949] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc/mmc@7e202000[0]' [ 2.055965] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc/mmc@7e202000[0]' [ 2.055974] sdhost-bcm2835 3f202000.mmc: using lookup tables for GPIO lookup [ 2.055982] sdhost-bcm2835 3f202000.mmc: No GPIO consumer wp found [ 2.093861] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 2.103010] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 2.112117] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 2.122385] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 2.129844] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1) [ 2.138749] of_cfs_init [ 2.139460] usb 1-1.1: new high-speed USB device number 3 using dwc_otg [ 2.143090] of_cfs_init: OK [ 2.217174] Waiting for root device /dev/mmcblk0p2... [ 2.241364] mmc1: new high speed SDIO card at address 0001 [ 2.248786] mmcblk mmc1:0001: no of_node; not parsing pinctrl DT [ 2.259874] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.279669] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3 [ 2.281655] mmc0: new high speed SDHC card at address aaaa [ 2.291656] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.299116] mmcblk mmc0:aaaa: no of_node; not parsing pinctrl DT [ 2.308806] hub 1-1.1:1.0: USB hub found [ 2.308876] mmcblk0: mmc0:aaaa SC16G 14.8 GiB [ 2.321057] hub 1-1.1:1.0: 3 ports detected [ 2.326439] mmcblk0: p1 p2 [ 2.351091] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null) [ 2.362573] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.374885] devtmpfs: mounted [ 2.382728] Freeing unused kernel memory: 2048K [ 2.389850] Run /sbin/init as init process [ 2.471768] init: Console is alive [ 2.477518] init: - watchdog - [ 2.684847] dwc_otg_handle_wakeup_detected_intr lxstate = 2 [ 3.089436] usb 1-1.1.1: new high-speed USB device number 4 using dwc_otg [ 3.114025] kmodloader: loading kernel modules from /etc/modules-boot.d/ [ 3.135414] pps_core: LinuxPPS API ver. 1 registered [ 3.141340] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 3.157738] PTP clock support registered [ 3.173252] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.184860] ehci-fsl: Freescale EHCI Host controller driver [ 3.196543] ehci-platform: EHCI generic platform driver [ 3.209636] libata version 3.00 loaded. [ 3.213386] kmodloader: done loading kernel modules from /etc/modules-boot.d/ [ 3.229241] init: - preinit - [ 3.233848] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800, bcdDevice= 3.00 [ 3.246750] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.259882] lan78xx 1-1.1.1:1.0: no of_node; not parsing pinctrl DT [ 3.522158] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): No External EEPROM. Setting MAC Speed [ 3.537588] mdio_bus usb-001:004: GPIO lookup for consumer reset [ 3.537597] mdio_bus usb-001:004: using device tree for GPIO lookup [ 3.537623] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc/usb@7e980000/usb-port@1/usb-port@1/ethernet@1/mdio[0]' [ 3.537642] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/soc/usb@7e980000/usb-port@1/usb-port@1/ethernet@1/mdio[0]' [ 3.537653] mdio_bus usb-001:004: using lookup tables for GPIO lookup [ 3.537662] mdio_bus usb-001:004: No GPIO consumer reset found [ 3.537668] libphy: lan78xx-mdiobus: probed [ 3.541328] random: procd: uninitialized urandom read (4 bytes read) [ 3.576624] mdio_bus usb-001:004:01: GPIO lookup for consumer reset [ 3.576636] mdio_bus usb-001:004:01: using device tree for GPIO lookup [ 3.576665] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc/usb@7e980000/usb-port@1/usb-port@1/ethernet@1/mdio/ethernet-phy@1[0]' [ 3.576684] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/soc/usb@7e980000/usb-port@1/usb-port@1/ethernet@1/mdio/ethernet-phy@1[0]' [ 3.576696] mdio_bus usb-001:004:01: using lookup tables for GPIO lookup [ 3.576705] mdio_bus usb-001:004:01: No GPIO consumer reset found [ 3.580952] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): int urb period 64 [ 6.456431] mount_root: mounting /dev/root [ 6.463327] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended [ 6.481155] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 6.489252] mount_root: loading kmods from internal overlay [ 6.535912] kmodloader: loading kernel modules from //etc/modules-boot.d/ [ 6.547208] kmodloader: done loading kernel modules from //etc/modules-boot.d/ [ 6.666522] block: attempting to load /etc/config/fstab [ 6.680152] block: extroot: not configured [ 6.728324] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 6.749946] urandom-seed: Seeding with /etc/urandom.seed [ 6.814689] procd: - early - [ 6.819976] procd: - watchdog - [ 6.956394] random: jshn: uninitialized urandom read (4 bytes read) [ 7.079672] random: jshn: uninitialized urandom read (4 bytes read) [ 7.192777] random: jshn: uninitialized urandom read (4 bytes read) [ 7.376157] procd: - watchdog - [ 7.382083] procd: - ubus - [ 7.438478] procd: - init - [ 7.448153] uart-pl011 3f201000.serial: no DMA platform data [ 7.952802] kmodloader: loading kernel modules from /etc/modules.d/* [ 7.960097] urngd: v1.0.2 started. [ 7.991251] natsemi dp8381x driver, version 2.1, Sept 11, 2006 [ 7.991251] originally by Donald Becker becker@scyld.com [ 7.991251] 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder [ 8.033435] zram: Added device: zram0 [ 8.044541] random: crng init done [ 8.048019] NET: Registered protocol family 8 [ 8.050069] random: 6 urandom warning(s) missed due to ratelimiting [ 8.056371] NET: Registered protocol family 20 [ 8.107508] NET: Registered protocol family 15 [ 8.115954] Initializing XFRM netlink socket [ 8.129255] Modular ISDN core version 1.1.29 [ 8.136185] NET: Registered protocol family 34 [ 8.144314] mISDN: Layer-1-over-IP driver Rev. 2.00 [ 8.157921] 0 virtual devices registered [ 8.168452] DSP module 2.0 [ 8.172913] mISDN_dsp: DSP clocks every 80 samples. This equals 1 jiffies. [ 8.228716] tun: Universal TUN/TAP device driver, 1.6 [ 8.243462] mISDN: HFC-multi driver 2.03 [ 8.294360] sctp: Hash tables configured (bind 512/512) [ 8.307301] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 8.320618] nat46: module (version 362640b41ae52b732d9e9729e61ac555492442a3) loaded. [ 8.342329] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 8.351444] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 8.372685] VMware vmxnet3 virtual NIC driver - version 1.4.17.0-k-NAPI [ 8.386845] gre: GRE over IPv4 demultiplexor driver [ 8.395588] ip_gre: GRE over IPv4 tunneling driver [ 8.409278] ip6_gre: GRE over IPv6 tunneling driver [ 8.425500] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 8.552467] i2c /dev entries driver [ 8.573770] hidraw: raw HID events driver (C) Jiri Kosina [ 8.585407] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned. [ 8.623087] Mirror/redirect action on [ 8.634740] u32 classifier [ 8.639705] input device check on [ 8.645716] Actions configured [ 8.660490] GACT probability on [ 8.668591] Simple TC action Loaded [ 8.740911] 8139too: 8139too Fast Ethernet driver 0.9.28 [ 8.846033] usbcore: registered new interface driver asix [ 8.860771] Atheros(R) L2 Ethernet Driver - version 2.2.3 [ 8.868136] Copyright (c) 2007 Atheros Corporation. [ 8.881407] usbcore: registered new interface driver ax88179_178a [ 8.894682] usbcore: registered new interface driver cdc_acm [ 8.902209] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 8.914549] usbcore: registered new interface driver cdc_eem [ 8.923578] usbcore: registered new interface driver cdc_ether [ 8.933384] usbcore: registered new interface driver cdc_ncm [ 8.941555] usbcore: registered new interface driver cdc_subset [ 8.950526] usbcore: registered new interface driver cdc_wdm [ 8.958952] Loading modules backported from Linux version v5.8-0-gbcf876870b95 [ 8.967974] Backport generated by backports.git v5.8-1-0-g79400d9e [ 8.981148] usbcore: registered new interface driver dm9601 [ 8.990003] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI [ 8.997851] e100: Copyright(c) 1999-2006 Intel Corporation [ 9.009020] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 9.016723] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 9.038549] hso: drivers/net/usb/hso.c: Option Wireless [ 9.045946] usbcore: registered new interface driver hso [ 9.054271] usbcore: registered new interface driver huawei_cdc_ncm [ 9.067795] usbcore: registered new interface driver ipheth [ 9.087285] usbcore: registered new interface driver kalmia [ 9.106093] usbcore: registered new interface driver kaweth [ 9.118556] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 9.130615] ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker [ 9.228513] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de [ 9.239167] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 9.260564] usbcore: registered new interface driver pegasus [ 9.269838] usbcore: registered new interface driver qmi_wwan [ 9.280680] usbcore: registered new interface driver r8152 [ 9.291291] r8712u: module is from the staging directory, the quality is unknown, you have been warned. [ 9.306676] usbcore: registered new interface driver r8712u [ 9.316550] usbcore: registered new interface driver rndis_host [ 9.325637] usbcore: registered new interface driver rtl8150 [ 9.335103] usbcore: registered new interface driver sierra_net [ 9.345259] sis900.c: v1.08.10 Apr. 2 2006 [ 9.361965] sky2: driver version 1.30 [ 9.385932] usbcore: registered new interface driver smsc75xx [ 9.396626] Solos PCI Driver Version 1.04 [ 9.403970] usbcore: registered new interface driver sr9700 [ 9.414389] tulip: Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007) [ 9.426336] usbcore: registered new interface driver usbhid [ 9.433886] usbhid: USB HID core driver [ 9.444633] usbcore: registered new interface driver usbserial_generic [ 9.453230] usbserial: USB Serial support registered for generic [ 9.462915] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker [ 9.474490] usbcore: registered new interface driver visor [ 9.481968] usbserial: USB Serial support registered for Handspring Visor / Palm OS [ 9.494079] usbserial: USB Serial support registered for Sony Clie 5.0 [ 9.503237] usbserial: USB Serial support registered for Sony Clie 3.5 [ 9.757885] xt_ndpi v1.2 ndpi 3.5.0 IPv6=YES debug_message=no [ 9.757885] BT: hash_size 0k, hash_expiation 0 sec, log_size 128kb [ 9.757885] sizeof hash_ip4p_node=32 id_struct=240 [ 9.757885] flow_struct=1496 packet_struct=736 [ 9.757885] flow_tcp_struct=100 flow_udp_struct=40 int_one_line_struct=8 [ 9.757885] ndpi_ip_addr_t=16 ndpi_protocol=4 nf_ct_ext_ndpi=152 [ 9.757885] flow_info=112 spinlock_t=4 NF_EXT_ID 7 [ 9.813557] xt_ndpi: MAX_PROTOCOLS 320 LAST_PROTOCOL 254 [ 9.821051] xt_ndpi: flow acctounting OFF [ 9.840138] xt_time: kernel timezone is -0000 [ 9.847698] usbcore: registered new interface driver ark3116 [ 9.855576] usbserial: USB Serial support registered for ark3116 [ 9.865319] usbcore: registered new interface driver belkin_sa [ 9.873577] usbserial: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter [ 9.891565] usbcore: registered new interface driver cdc_mbim [ 9.940950] usbcore: registered new interface driver ch341 [ 9.948594] usbserial: USB Serial support registered for ch341-uart [ 9.958499] usbcore: registered new interface driver cp210x [ 9.966314] usbserial: USB Serial support registered for cp210x [ 9.979558] usbcore: registered new interface driver cypress_m8 [ 9.998629] usbserial: USB Serial support registered for DeLorme Earthmate USB [ 10.008087] usbserial: USB Serial support registered for HID->COM RS232 Adapter [ 10.017787] usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter [ 10.033105] usbcore: registered new interface driver ftdi_sio [ 10.041289] usbserial: USB Serial support registered for FTDI USB Serial Device [ 10.052147] usbcore: registered new interface driver garmin_gps [ 10.060245] usbserial: USB Serial support registered for Garmin GPS usb/tty [ 10.071829] usbcore: registered new interface driver keyspan [ 10.079688] usbserial: USB Serial support registered for Keyspan - (without firmware) [ 10.091858] usbserial: USB Serial support registered for Keyspan 1 port adapter [ 10.101586] usbserial: USB Serial support registered for Keyspan 2 port adapter [ 10.111198] usbserial: USB Serial support registered for Keyspan 4 port adapter [ 10.187810] usbcore: registered new interface driver mct_u232 [ 10.195698] usbserial: USB Serial support registered for MCT U232 [ 10.206044] usbcore: registered new interface driver mos7720 [ 10.213891] usbserial: USB Serial support registered for Moschip 2 port adapter [ 10.226070] usbcore: registered new interface driver mt7601u [ 10.235374] usbcore: registered new interface driver oti6858 [ 10.243188] usbserial: USB Serial support registered for oti6858 [ 10.252934] usbcore: registered new interface driver pl2303 [ 10.260925] usbserial: USB Serial support registered for pl2303 [ 10.275338] PPP generic driver version 2.4.2 [ 10.284206] NET: Registered protocol family 24 [ 10.318589] usbcore: registered new interface driver rtl8187 [ 10.328980] usbcore: registered new interface driver rtl8xxxu [ 10.357383] usbcore: registered new interface driver sierra [ 10.364951] usbserial: USB Serial support registered for Sierra USB modem [ 10.375232] usbcore: registered new interface driver ti_usb_3410_5052 [ 10.384025] usbserial: USB Serial support registered for TI USB 3410 1 port adapter [ 10.395959] usbserial: USB Serial support registered for TI USB 5052 2 port adapter [ 10.409180] usbcore: registered new interface driver usb_serial_simple [ 10.417937] usbserial: USB Serial support registered for carelink [ 10.426292] usbserial: USB Serial support registered for zio [ 10.434112] usbserial: USB Serial support registered for funsoft [ 10.442109] usbserial: USB Serial support registered for flashloader [ 10.450364] usbserial: USB Serial support registered for google [ 10.458260] usbserial: USB Serial support registered for libtransistor [ 10.466772] usbserial: USB Serial support registered for vivopay [ 10.474617] usbserial: USB Serial support registered for moto_modem [ 10.482700] usbserial: USB Serial support registered for motorola_tetra [ 10.491198] usbserial: USB Serial support registered for novatel_gps [ 10.499482] usbserial: USB Serial support registered for hp4x [ 10.507060] usbserial: USB Serial support registered for suunto [ 10.514910] usbserial: USB Serial support registered for siemens_mpi [ 10.593389] brcmfmac mmc1:0001:1: no of_node; not parsing pinctrl DT [ 10.593581] brcmfmac mmc1:0001:2: no of_node; not parsing pinctrl DT [ 10.599529] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 10.787126] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 10.815026] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-febaba43 [ 10.866490] brcmfmac mmc1:0001:3: no of_node; not parsing pinctrl DT [ 10.866728] usbcore: registered new interface driver brcmfmac [ 10.875710] usbcore: registered new interface driver ipw [ 10.882728] usbserial: USB Serial support registered for IPWireless converter [ 10.893135] usbcore: registered new interface driver option [ 10.900543] usbserial: USB Serial support registered for GSM modem (1-port) [ 10.914025] usbcore: registered new interface driver qcserial [ 10.922326] usbserial: USB Serial support registered for Qualcomm USB modem [ 10.948212] usbcore: registered new interface driver rt2800usb [ 10.973212] usbcore: registered new interface driver rtl8192cu [ 10.991714] usbcore: registered new interface driver ath9k_htc [ 11.005149] kmodloader: done loading kernel modules from /etc/modules.d/* [ 17.677568] 8021q: adding VLAN 0 to HW filter on device eth0 [ 17.679227] lan78xx 1-1.1.1:1.0 eth0: kevent 4 may have been dropped [ 17.698585] 8021q: adding VLAN 0 to HW filter on device wan1 [ 17.716340] 8021q: adding VLAN 0 to HW filter on device wan2 [ 17.727802] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 17.737909] IPv6: ADDRCONF(NETDEV_CHANGE): wan1: link becomes ready [ 17.747156] IPv6: ADDRCONF(NETDEV_CHANGE): wan2: link becomes ready [ 18.172074] EXT4-fs error (device mmcblk0p2): ext4_mb_generate_buddy:747: group 1, block bitmap and bg descriptor inconsistent: 12991 vs 12992 free clusters [ 18.194582] EXT4-fs (mmcblk0p2): Remounting filesystem read-only [ 18.206717] EXT4-fs (mmcblk0p2): ext4_writepages: jbd2_start: 2147483646 pages, ino 1002; err -30

Dites-moi si cela suffit, c'est pas simple de tomber au bon moment... Merci !

Ysurac commented 3 years ago

Comme c'est indiqué le système de fichier est monté en lecture seule. Ce qui n'est pas bon du tout. Soucis de carte SD ou redémarrage violent. Sinon rien indique un plantage du routeur.

Kalimeiro commented 3 years ago

Bonjour,

Cela semble être le même problème que j'ai déjà remonté il y a un moment avec les RPI3B+, pour ma part, et ce n'est que mon avis : OMR ne fonctionne PAS avec un RPI3B+ à cause d'un violent bug du noyau/eeprom/driver/jensaisrien de la carte réseau, ce bug est apparu de mémoire depuis la 0.53.x

Comme décrit, le système en lecture seule et normal compte tenu des redémarrages violent, d'ailleurs sur ce sujet l'option "verifier les systèmes de fichiers avant le montage" devait être modifié et activé par défaut dans la 0.57.3 et ce n'est toujours pas le cas, cette option activé par défaut évite que les partitions soient monté en lecture seule lors d'un redémarrage violent, cela clean le système de fichier ... quand il est activé ça fonctionne bien.

mathchab commented 3 years ago

Bonjour,

Du coup, malgré les réinstallations, impossible de retrouver un système fonctionnel (malgré 2 ans d’utilisation).

J’ai switché sur une VM ESXi 6.7 et ça marche vraiment bien, facilement duplicable avant update (au cas où), etc.

On peut clore le sujet, même si je me doute que quelqu’un d’autre se retrouvera dans cette situation.

Merci !

Ysurac commented 3 years ago

L'option "verifier les systèmes de fichiers avant le montage" est bien mise par défaut dans la configuration, mais elle est bizarrement supprimée à un moment par le boot sans que j'en sache le responsable. Pour le RPI3B+, les patches sont ceux par défaut d'OpenWrt maintenant. Je pourrais reprendre les patches officiels venant de raspberry mais ça a déjà posé des soucis et nécessite beaucoup de tests. La solution serait d'ajouter uniquement le patch nécessaire, mais faut le trouver si il existe et arriver à reproduire le soucis qui ne se produit pas systématiquement.

github-actions[bot] commented 3 years ago

This issue is stale because it has been open 90 days with no activity. Remove stale label or comment or this will be closed in 5 days