search

agraton32 / reaver-wps

Automatically exported from code.google.com/p/reaver-wps
0 stars 0 forks source link

wash command wont work . #217

Open GoogleCodeExporter opened 8 years ago

GoogleCodeExporter commented 8 years ago 
A few things to consider before submitting an issue:

0. We write documentation for a reason, if you have not read it and are
having problems with Reaver these pages are required reading before
submitting an issue:
http://code.google.com/p/reaver-wps/wiki/HintsAndTips
http://code.google.com/p/reaver-wps/wiki/README
http://code.google.com/p/reaver-wps/wiki/FAQ
http://code.google.com/p/reaver-wps/wiki/SupportedWirelessDrivers
1. Reaver will only work if your card is in monitor mode.  If you do not
know what monitor mode is then you should learn more about 802.11 hacking
in linux before using Reaver.
2. Using Reaver against access points you do not own or have permission to
attack is illegal.  If you cannot answer basic questions (i.e. model
number, distance away, etc) about the device you are attacking then do not
post your issue here.  We will not help you break the law.
3. Please look through issues that have already been posted and make sure
your question has not already been asked here: http://code.google.com/p
/reaver-wps/issues/list
4. Often times we need packet captures of mon0 while Reaver is running to
troubleshoot the issue (tcpdump -i mon0 -s0 -w broken_reaver.pcap).  Issue
reports with pcap files attached will receive more serious consideration.

Answer the following questions for every issue submitted:

0. What version of Reaver are you using?  (Only defects against the latest
version will be considered.)
reaver 1.4
1. What operating system are you using (Linux is the only supported OS)?
back track 5
2. Is your wireless card in monitor mode (yes/no)?
yes
3. What is the signal strength of the Access Point you are trying to crack?
yes
4. What is the manufacturer and model # of the device you are trying to
crack?
dlink
5. What is the entire command line string you are supplying to reaver?

svn checkout http://reaver-wps.googlecode.com/svn/trunk/

ls

cd trunk/

ls

cd src/

ls

./configure

make install

ls

./wash
airmon-ng start wlan0
airodump-ng mon0
reaver-i mon0 -b (BSSID)

6. Please describe what you think the issue is.
./wash command wont work, and a message display 

Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

when i type command '' airmon-ng start wlan0 

how to solve those problem ?

7. Paste the output from Reaver below.

root@root:~/trunk/src# make install
rm -f /usr/local/bin/reaver /usr/local/bin/wash /usr/local/bin/walsh
if [ ! -d /usr/local/etc/reaver ]; then mkdir -p /usr/local/etc/reaver; fi
if [ ! -e /usr/local/etc/reaver/reaver.db ]; then cp reaver.db 
/usr/local/etc/reaver/reaver.db && chmod -R a+rw /usr/local/etc/reaver; fi
if [ -e wash ]; then cp wash /usr/local/bin/wash; fi
if [ -e reaver ]; then cp reaver /usr/local/bin/reaver; fi
root@root:~/trunk/src# ./wash
bash: ./wash: No such file or directory
root@root:~/trunk/src# .wash
.wash: command not found
root@root:~/trunk/src#  ./wash
bash: ./wash: No such file or directory
root@root:~/trunk/src# airmon-ng start wlan0

Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID Name
2710    dhclient3
2711    dhclient3
2799    dhclient
Process with PID 2711 (dhclient3) is running on interface wlan0

Interface   Chipset     Driver

wlan0       Atheros AR9280  ath9k - [phy0]
                (monitor mode enabled on mon0)

Original issue reported on code.google.com by lunglung...@gmail.com on 4 Feb 2012 at 11:03

GoogleCodeExporter commented 8 years ago 
simply type wash without dot or something else...

Original comment by AdiR...@gmail.com on 4 Feb 2012 at 11:23

GoogleCodeExporter commented 8 years ago 
but after i type wash command , it will display command at below .

root@root:~/trunk/src# wash
No command 'wash' found, did you mean:
 Command 'ash' from package 'ash' (universe)
 Command 'bash' from package 'bash' (main)
 Command 'dash' from package 'dash' (main)
 Command 'kash' from package 'kanif' (universe)
 Command 'wish' from package 'tk8.3' (universe)
 Command 'wish' from package 'tk8.4' (main)
 Command 'wish' from package 'tk8.5' (main)
 Command 'wish' from package 'tk' (main)
 Command 'nash' from package 'lrslib' (universe)
 Command 'sash' from package 'sash' (universe)
wash: command not found
root@root:~/trunk/src# 

what mean ? then what next ?

Original comment by lunglung...@gmail.com on 4 Feb 2012 at 11:57

GoogleCodeExporter commented 8 years ago 
mb you forgot about 'make' command before 'make install'

Original comment by lulzse...@gmail.com on 4 Feb 2012 at 12:41

GoogleCodeExporter commented 8 years ago 
oic... can u let me know the completely command from install the reaver process 
until the end . thx =0

btw what about this msg meaning ?

Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

Original comment by lunglung...@gmail.com on 4 Feb 2012 at 1:28

GoogleCodeExporter commented 8 years ago 
http://code.google.com/p/reaver-wps/wiki/README

INSTALLATION

    Reaver is only supported on the Linux platform, requires the libpcap and libsqlite3 libraries, and can be built and installed by running: 

                $ ./configure
                $ make
                # make install

Original comment by hurenhan...@googlemail.com on 4 Feb 2012 at 3:05

GoogleCodeExporter commented 8 years ago 
i using live boot usb pendrive , so i need download reaver everytime when i 
needed.
so everytime i type all those command shown as below :

svn checkout http://reaver-wps.googlecode.com/svn/trunk/
ls
cd trunk/
ls
cd src/
ls
./configure
make 
make install
ls
wash <--------- ( but everytime the process until here cant continue , the 
error msg just what i posted just now)

airmon-ng 
airmon-ng start wlan0
reaver -i mon0 -b (BSSID)

IS THAT ALL CORRECT ?

Original comment by lunglung...@gmail.com on 4 Feb 2012 at 3:30

GoogleCodeExporter commented 8 years ago 
run 'wash' on time, just for choose BSSID, then kill it proc and run 'reaver'.
and before run 'wash' exec 'airmon-ng srart wlan0' (one time for all your 
session with LiveCD)

...
...
make install
airmon-ng start wlan0
wash -i mon0 (here we take BSSID with max level pwr priority)
reaver -i mon0 -b BSSID -vv

Original comment by lulzse...@gmail.com on 4 Feb 2012 at 5:29

GoogleCodeExporter commented 8 years ago 
woo... thx dude.... it's work =D

Original comment by lunglung...@gmail.com on 5 Feb 2012 at 9:39

GoogleCodeExporter commented 8 years ago 
It doesn't work with installing via apt-get in Backtrack 5.

Original comment by joshuavi...@gmail.com on 14 Feb 2012 at 7:35

GoogleCodeExporter commented 8 years ago 
Hello there, im trying to make a script, that make it easy to crack wps, could 
you please save me the time and create one, it would be like this, the code 
will ask various questions such as if the wifi card plugged in and it will scan 
the wireless network and show the vulnerable clients, then it would create an 
array, the output in the terminal window will ask you which network would you 
obtain, you will type in 0 1 2 3 etc depends on the array after, it will start 
cracking it for you, when it has been completed it will save the keys 
information into a folder or database, if you can use this into metasploit 
framework or create the code into python that would be fucking asum, as well if 
you can generate this code into a linksys router that would be sick! what about 
an AIROS the are unlimited possibilities

Original comment by leacocks...@gmail.com on 17 Feb 2012 at 11:27

GoogleCodeExporter commented 8 years ago 
Hi to all, I have Back Track 5 R2, it has reaver in it already, no installing 
needed! i to get the

Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

message, i just type: airmon-ng check kill

this solves that problem, Now my problem.

wash -i mon0/wlan0(either) doesn't work, all i get is an error scrolling sayin

found bad FCS packet, skipping,
found bad FCS packet, skipping,
found bad FCS packet, skipping, and so-on

then when i use reaver i can authenticate and try pin 12345670 but then it 
keeps repeating that same pin, eventually starts to say period timed out or 
something similar, ideas anyone??

Original comment by MrCra...@gmail.com on 18 Apr 2012 at 12:58

GoogleCodeExporter commented 8 years ago 
error: pcap library not found!
this problem 
 pleas tell me the soulition :)
when ./configure  ????

Original comment by tawfikch...@yahoo.com on 7 May 2012 at 4:39

GoogleCodeExporter commented 8 years ago 
try install libsqlite3-dev

Original comment by lulzse...@gmail.com on 7 May 2012 at 6:09

GoogleCodeExporter commented 8 years ago 
root@bt:~# wash -i mon0

Wash v1.4 WiFi Protected Setup Scan Tool
Copyright (c) 2011, Tactical Network Solutions, Craig Heffner 
<cheffner@tacnetsol.com>

BSSID                  Channel       RSSI       WPS Version       WPS Locked    
    ESSID
--------------------------------------------------------------------------------
-------------------------------
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
[!] Found packet with bad FCS, skipping...
^C
root@bt:~# 

Anybody any idea what might be wrong?

Original comment by attil...@gmail.com on 25 Jul 2012 at 10:30

GoogleCodeExporter commented 8 years ago 
just run wash with -C arg.
wash -i mon0 -C

Original comment by lulzse...@gmail.com on 25 Jul 2012 at 10:42

GoogleCodeExporter commented 8 years ago 
is any reaver command i can run if i already have wps pin and want to convert 
it to WPA PSK???

Original comment by harikar...@gmail.com on 5 Aug 2012 at 9:16

GoogleCodeExporter commented 8 years ago 
Hi to all, I have Back Track 5 R2, it has reaver in it already, no installing 
needed! i to get the

Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

message, i just type: airmon-ng check kill

this solves that problem, Now my problem.

wash -i mon0/wlan0(either) doesn't work, all i get is an error scrolling sayin

found bad FCS packet, skipping,
found bad FCS packet, skipping,
found bad FCS packet, skipping, and so-on

then when i use reaver i can authenticate and try pin 12345670 but then it 
keeps repeating that same pin, eventually starts to say period timed out or 
something similar, ideas anyone??
-------------------------------------------------------------
I know I had this same problem but I found out why.

You are probably trying to run the command with you built-in wireless adapter 
which was what I did and if you type in airmon-ng as root you will see your 
chipset model and mine is a Intel.
Intel chipsets for some reason times out and keeps of repeating the same PIN 
while using reaver. What I did was. I bought an external antena from ALPHA that 
had a realtek chipset. Once I plugged it in and ran the reaver command once 
again. It worked like a charm!!

Original comment by johny...@gmail.com on 30 Dec 2012 at 4:09

GoogleCodeExporter commented 8 years ago 
root@bt:~/trunk/src# ./wash
bash: ./wash: No such file or directory
root@bt:~/trunk/src# airmon-ng start wlan0

Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID Name
2130    dhclient3
2224    dhclient
2246    dhclient

Interface   Chipset     Driver

root@bt:~/trunk/src# airodump-ng mon0
Interface mon0: 
ioctl(SIOCGIFINDEX) failed: No such device
root@bt:~/trunk/src# reaver-i mon0 -b (BSSID)
bash: syntax error near unexpected token `('
root@bt:~/trunk/src# ./wash command wont work, and a message display
bash: ./wash: No such file or directory
root@bt:~/trunk/src# airmon-ng start wlan0 

please help

Original comment by dahraiak...@gmail.com on 20 Apr 2013 at 10:05

GoogleCodeExporter commented 8 years ago 
wash not scanning at all in ubuntu 14.04. immediately stop after starting. wifi 
drivers patched, working properly with wepcrackGUI.

root@ua:/home/ua# ^C
root@ua:/home/ua# sudo wash -i mon0 -C

Wash v1.4 WiFi Protected Setup Scan Tool
Copyright (c) 2011, Tactical Network Solutions, Craig Heffner 
<cheffner@tacnetsol.com>

BSSID                  Channel       RSSI       WPS Version       WPS Locked    
    ESSID
--------------------------------------------------------------------------------
-------------------------------

root@ua:/home/ua#

Original comment by olegfila...@gmail.com on 5 May 2014 at 9:08

GoogleCodeExporter commented 8 years ago 
The reason why reaver & wash not work in Ubuntu 14.04 is the new version of 
libpcap & libpcap-dev, which is probably have some bug or incompatibility.

You can downgrade to version from Ubuntu 13.10:

wget 
http://mirrors.kernel.org/ubuntu/pool/main/libp/libpcap/libpcap0.8_1.4.0-2_amd64
.deb 
http://mirrors.kernel.org/ubuntu/pool/main/libp/libpcap/libpcap0.8-dev_1.4.0-2_a
md64.deb
sudo dpkg -i libpcap0.8_1.4.0-2_amd64.deb libpcap0.8-dev_1.4.0-2_amd64.deb

Original comment by kib0rg1...@gmail.com on 12 May 2014 at 6:27

GoogleCodeExporter commented 8 years ago 
On arch linux this was what worked for me...
1) Use 'pacman -Rdd libpcap' if you already have it installed this will remove 
it.
2) Then get the 1.3.0 libpcap from 
http://www.tcpdump.org/release/libpcap-1.3.0.tar.gz.
3) Unpack it and cd into it and run './configure --prefix=/usr'.
4) 'make'
5) 'make install'

After that rebuild reaver and wash.
Not sure the effect this will have on programs which may rely on newest version 
like say tcpdump and wireshark but I'm sure I'll find out soon enough. Good 
luck.

Original comment by shakeyma...@gmail.com on 11 Jun 2014 at 11:23

GoogleCodeExporter commented 8 years ago 
I was having trouble running Reaver 1.4 on raspberry pi so I removed the 
installation and installed version1.3

When I run walsh -i mon0 all I get is the walsh help file displaying. Walsh 
does not start the scan. mon0 works fine when using airodump-ng mon0 so I'm 
scratching my head.

Any pointers much appreciated. Thanks.

Original comment by grahamcn...@googlemail.com on 13 Sep 2014 at 8:12

GoogleCodeExporter commented 8 years ago 
[deleted comment]
GoogleCodeExporter commented 8 years ago 
i have this problem on Kali 1.0.9 

Wash v1.4 WiFi Protected Setup Scan Tool
Copyright (c) 2011, Tactical Network Solutions, Craig Heffner 
<cheffner@tacnetsol.com>

BSSID                  Channel       RSSI       WPS Version       WPS Locked    
    ESSID
--------------------------------------------------------------------------------
-------------------------------

wash is not working and reaver failed to associate,,, typical problem of 
reaver..

Original comment by black.do...@gmail.com on 11 Oct 2014 at 9:13

GoogleCodeExporter commented 8 years ago 
i have tried every command ans still my airmon-ng command is not working.

wash v1.4 wifi protected setup scan tool.

Original comment by muhammad...@gmail.com on 19 Dec 2014 at 12:06

GoogleCodeExporter commented 8 years ago 
The reason why airmon-ng is coming up empty-handed in the guest is that you do 
not have control of the wireless card, in the guest.The hypervisor sets up a 
connection that allows you to share your internet connection, but it does so by 
creating a virtual ethernet interface which is bridged with the host extant 
connection.

You can double check my words by typing the command "iwconfig", it will show 
that you have no wifi-capable cards on your VM.

The way to gain access to the wifi doman is by means of a USB wifi adapter. 
There are many guides about that in Google, there are even small movies on 
youtube. You only have to learn how to transfer control of USB devices from the 
host to the guest, and the rest is trivial.

Original comment by muhammad...@gmail.com on 19 Dec 2014 at 12:08

GoogleCodeExporter commented 8 years ago 
how to transfer control of USB devices from the host to the guest

Original comment by muhammad...@gmail.com on 19 Dec 2014 at 12:09