bigjosh TSL issues - Githubissues

bigjosh / TSL

CW&T Time Since Launch

https://cwandt.com/products/time-since-launch

Other

13 stars 6 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Add a license

#65 grantstephens closed 2 months ago
3
2021 09 run

#64 bigjosh closed 2 years ago
0
Tie EVIN pin to RTC_VCC

#63 bigjosh closed 4 years ago
0
Quadruple check orientation of LEDs on ver6

#62 bigjosh closed 4 years ago
1
Make firmware check PCB version and then open or close MOS appropriately.

#61 bigjosh opened 4 years ago
0
Replace backup CAPs with shorter ones so LCD can fit flatter now that RTC is low version

#60 bigjosh closed 4 years ago
1
Copper between mounting hole and switch pad does not match gerbers

#59 bigjosh opened 4 years ago
0
Remove silk from around the endcap contact plate

#58 bigjosh closed 4 years ago
0
Update firmware for new backup power circuit

#57 bigjosh opened 4 years ago
0
Mounting holes too tight with new plating

#56 bigjosh opened 4 years ago
0
Reduce footprint of ATXMEGA center pad

#55 bigjosh closed 4 years ago
0
Use virtual ports on the FOUT pin to reduce power

#54 bigjosh closed 5 years ago
1
Rubbing causes spurious resets

#53 bigjosh opened 5 years ago
1
"ClockError” failures after programming

#52 bigjosh closed 5 years ago
1
Skipped counts from rubbing

#51 bigjosh closed 5 years ago
1
Use optimal code generated code to implement digit updating

#50 bigjosh closed 4 years ago
1
Internally sampled voltage is consistantly ~0.2V lower than real Vcc

#49 bigjosh opened 5 years ago
0
Test pin shows clock time on power up?

#48 bigjosh closed 5 years ago
1
Occasional and transatory differnece calculation failure?

#47 bigjosh closed 5 years ago
0
Add (c) egg

#46 bigjosh closed 5 years ago
1
Check for low battery

#45 bigjosh closed 5 years ago
1
Merge BOM

#44 bigjosh closed 5 years ago
0
Try to make more room on the PCB for the level getting bent under the trigger switch

#43 bigjosh closed 5 years ago
1
Deal with 100 year rollover?

#42 bigjosh closed 5 years ago
0
Should we show anything on the display on a warm start?

#41 bigjosh closed 5 years ago
2
Get rid of silk pin 1 dot on XMEGA

#40 bigjosh closed 5 years ago
0
Pick pattern for flash

#39 bigjosh closed 5 years ago
1
Can we save some cycles by skipping ISR on FOUT interrupts?

#38 bigjosh closed 5 years ago
1
Add low battery detection

#37 bigjosh closed 5 years ago
1
What actual 8 seg messages should we show on time lost and low batt?

#36 bigjosh closed 5 years ago
5
Reset RTC on trigger to 1PPS is exactly synced to pull

#35 bigjosh closed 5 years ago
1
Use smaller RX8900 variant?

#34 bigjosh closed 5 years ago
1
RX8900 footprint too small

#33 bigjosh closed 5 years ago
1
Battery holder alignment holes too big

#32 bigjosh closed 5 years ago
0
Move FOUT to PORTB2 (pin 59) so it can use RISING interrupt

#31 bigjosh closed 6 years ago
0
No connection from BAT-POS to Vcc!

#30 bigjosh closed 5 years ago
1
What to try two LEDs in the middle for symmetry and the give the flash a little sparkle by sequencing them?

#29 bigjosh closed 5 years ago
0
For the LCD pins, can we move the pins up a bit and keep the batteries centered?

#28 bigjosh closed 5 years ago
0
Trigger switch should be more centered?

#27 bigjosh closed 5 years ago
0
Ahhh! RIGHT HAND SWITCH!

#26 bigjosh closed 5 years ago
1
No traces on back side of PCB where they could short against end cap

#25 bigjosh closed 6 years ago
1
Can we update the label on the PCB?

#24 bigjosh closed 6 years ago
2
Vias and traces under the ATMEGA

#23 bigjosh closed 6 years ago
1
Potential short where board is screwed down to cap?

#22 bigjosh closed 6 years ago
1
Try to put a keep out on the bottom side of the board where the mounting screws are?

#21 bigjosh closed 6 years ago
1
Put some ISP pads really physically close to the XMEGA

#20 bigjosh closed 6 years ago
1
Undersize mounting screw holes

#19 bigjosh closed 6 years ago
1
Test break away tab for trigger

#18 bigjosh closed 6 years ago
1
Matte black soldermask

#17 bigjosh closed 6 years ago
0
Switch to other-handed button

#16 bigjosh closed 6 years ago
1