tft35 e3 v3 mixing hotend issue?

[taraxias]

please someone tell me what i am doing wrong.. i am going to brake it... i have made a custom printer with 3 steppers and a mixing hotend.. everything works fine,it prints fine exept that in touch mode i cant change between steppers to change filament. it only "reads" 1 stepper. i follow almost everything i have found in here and nothing,5 days now i cant fix it.. pleaseeeeee help. my motherboard is octopus v1.1 and tft35 e3 v3

M503 SENDING:M503 echo:; Linear Units: echo: G21 ; (mm) echo:; Temperature Units: echo: M149 C ; Units in Celsius echo:; Filament settings (Disabled): echo: M200 S0 D1.75 echo:; Steps per unit: echo: M92 X80.00 Y80.00 Z400.00 E93.00 echo:; Max feedrates (units/s): echo: M203 X500.00 Y500.00 Z20.00 E25.00 echo:; Max Acceleration (units/s2): echo: M201 X3000.00 Y3000.00 Z100.00 E10000.00 echo:; Acceleration (units/s2) (P R T): echo: M204 P1000.00 R500.00 T1000.00 echo:; Advanced (B S T J): echo: M205 B20000.00 S0.00 T0.00 J0.01 echo:; Home offset: echo: M206 X0.00 Y0.00 Z0.00 echo:; Auto Bed Leveling: echo: M420 S0 ; Leveling OFF echo:; Material heatup parameters: echo: M145 S0 H210.00 B65.00 F0 echo: M145 S1 H250.00 B110.00 F0 echo:; Hotend PID: echo: M301 P45.80 I3.61 D145.39 C100.00 L20 F10.00 echo:; Bed PID: echo: M304 P369.61 I54.13 D602.87 echo:; Power-loss recovery: echo: M413 S0 ; OFF echo:; Stepper driver current: echo: M906 X800 Y800 Z800 echo: M906 I1 Z800 echo: M906 T0 E800 echo: M906 T1 E800 echo: M906 T2 E800 echo:; Driver stepping mode: echo: M569 S1 X Y Z echo: M569 S1 I1 Z echo: M569 S1 T0 E echo: M569 S1 T1 E echo: M569 S1 T2 E echo:; Linear Advance: echo: M900 K0.00 echo:; Filament load/unload: echo: M603 L300.00 U450.00 ; (mm) echo:; Filament runout sensor: echo: M412 S1 ; Sensor ON ok P15 B3

M115 FIRMWARE_NAME:Marlin bugfix-2.1.x (Aug 23 2023 21:46:53) SOURCE_CODE_URL:github.com/MarlinFirmware/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:foteini is EXTRUDER_COUNT:1 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff Cap:SERIAL_XON_XOFF:0 Cap:BINARY_FILE_TRANSFER:0 Cap:EEPROM:1 Cap:VOLUMETRIC:1 Cap:AUTOREPORT_POS:1 Cap:AUTOREPORT_TEMP:1 Cap:PROGRESS:0 Cap:PRINT_JOB:1 Cap:AUTOLEVEL:0 Cap:RUNOUT:1 Cap:Z_PROBE:0 Cap:LEVELING_DATA:1 Cap:BUILD_PERCENT:1 Cap:SOFTWARE_POWER:0 Cap:TOGGLE_LIGHTS:0 Cap:CASE_LIGHT_BRIGHTNESS:0 Cap:EMERGENCY_PARSER:1 Cap:HOST_ACTION_COMMANDS:1 Cap:PROMPT_SUPPORT:1 Cap:SDCARD:1 Cap:MULTI_VOLUME:0 Cap:REPEAT:0 Cap:SD_WRITE:1 Cap:AUTOREPORT_SD_STATUS:1 Cap:LONG_FILENAME:1 Cap:LFN_WRITE:1 Cap:CUSTOM_FIRMWARE_UPLOAD:0 Cap:EXTENDED_M20:1 Cap:THERMAL_PROTECTION:1 Cap:MOTION_MODES:0 Cap:ARCS:1 Cap:BABYSTEPPING:1 Cap:EP_BABYSTEP:1 Cap:CHAMBER_TEMPERATURE:0 Cap:COOLER_TEMPERATURE:0 Cap:MEATPACK:0 Cap:CONFIG_EXPORT:0 ok P15 B3

[Services8810]

Try this one with your config.ini file

[Services8810]

Hope it works

[taraxias]

salvation....tyyyyyyyyyyy

[Services8810]

Xaxaxaxaxxaa

[Services8810]

Glad it worked!!!

[Services8810]

It is the 1st time I help someone in github. Usually someone helps me !

[taraxias]

thanks a lot for everything. i dont know what you have done better than me(i mean i have almost try everything) but thanks god you did it.. the next step was to use this screen to the voron i am making and just add a simple lcd dislay 12864 and no cat,no harm.. κανε με αν θες add στο φατσοβιβλιο. αν γραψεις γιαννης ταραξιας κυρατσης με ελληνικα θα μεμ βρεις. σε ευχαριστω και παλι για ολα

[Services8810]

Χαρηκα που βοηθησα. Δεν εχω fb... Και εγω δεν ξερω τι δεν δουλεψε σωστα στο δικο σου setup. Σου εστειλα ο,τι ηξερα και ειχα δοκιμασει εγω. Τελος καλο, ολα καλα. Ελπιζω να φτιαξεις πολλα ωραια πραγματα. Mixing can be quite complicated though. Try SuperslicerMX, it may help a lot

[github-actions[bot]]

This issue has been automatically locked since there has not been any recent activity after it was closed. Please open a new issue for related bugs.