search

bigtreetech / Tango-3D-Printer-Motherboard

An Open Source ATMEGA2560 based 3D printer controller board.
Apache License 2.0
22 stars 16 forks source link

MARLIN ISSUES #3

Open ryanhmonument opened 5 years ago

ryanhmonument commented 5 years ago

all three marlin tango revisions seem to be the same 1.1.8 and seem to be setup for a delta.. i'm fairly new to marlin, and i am trying to get my new board running on a cartesian, and currently i am getting an error as follows "homing_feedrate_xy was not declared in this scope" i have tried with my limited knowledge with no luck, if someone has the tango rumba up and running on a regular cartesian printer, i would love a copy and i cn just tweek my bed size, thermistors, probe, and leveling, lcd, and i should be able to upload and run, i have sucessfully got marlin uploaded to the board, however it's not a running setup, it says "printer killed, pleasse reset" after the marlin splash screen, i used my marlin setup that was running on my anet , nd just changed mother board to rumba. i am thankfull for any advice, or someone to share a running config..

jimhiggs commented 5 years ago

I downloaded the stock Marlin 1.1.9 firmware and started from there. You are welcome to try my conf file. Mine is a modified cubex wth E3d hotends, no hotbed heater, raising bed Z azis and all endstops set for top, left, rear as 0,0,0 and I then use gcode to center 0,0,0 at center of bed.

/** Marlin 3D Printer Firmware Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]

Based on Sprinter and grbl. Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm

This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/.

*/

/** Configuration.h

Basic settings such as:

*/

ifndef CONFIGURATION_H

define CONFIGURATION_H

define CONFIGURATION_H_VERSION 010109

//=========================================================================== //============================= Getting Started ============================= //===========================================================================

/** Here are some standard links for getting your machine calibrated:

http://reprap.org/wiki/Calibration http://youtu.be/wAL9d7FgInk http://calculator.josefprusa.cz http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide http://www.thingiverse.com/thing:5573 https://sites.google.com/site/repraplogphase/calibration-of-your-reprap http://www.thingiverse.com/thing:298812 */

//=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== // For a Delta printer start with one of the configuration files in the // example_configurations/delta directory and customize for your machine. //

//=========================================================================== //============================= SCARA Printer =============================== //=========================================================================== // For a SCARA printer start with the configuration files in // example_configurations/SCARA and customize for your machine. //

// @section info

// User-specified version info of this build to display in [Pronterface, etc] terminal window during // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this // build by the user have been successfully uploaded into firmware.

define STRING_CONFIG_H_AUTHOR "Me" // Who made the changes.

//#define SHOW_BOOTSCREEN //#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 //#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2

/**

// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. //#define SHOW_CUSTOM_BOOTSCREEN

// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. //#define CUSTOM_STATUS_SCREEN_IMAGE

// @section machine

/**

/** This setting determines the communication speed of the printer.

250000 works in most cases, but you might try a lower speed if you commonly experience drop-outs during host printing. You may try up to 1000000 to speed up SD file transfer.

:[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] */

define BAUDRATE 115200

// Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH

// The following define selects which electronics board you have. // Please choose the name from boards.h that matches your setup

ifndef MOTHERBOARD

define MOTHERBOARD BOARD_RUMBA

endif

// Optional custom name for your RepStrap or other custom machine // Displayed in the LCD "Ready" message

define CUSTOM_MACHINE_NAME "Reprap Cubex"

// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"

// @section extruder

// This defines the number of extruders // :[1, 2, 3, 4, 5]

define EXTRUDERS 1

// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.

define DEFAULT_NOMINAL_FILAMENT_DIA 1.75

// For Cyclops or any "multi-extruder" that shares a single nozzle. //#define SINGLENOZZLE

/** Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.

This device allows one stepper driver on a control board to drive two to eight stepper motors, one at a time, in a manner suitable for extruders.

This option only allows the multiplexer to switch on tool-change. Additional options to configure custom E moves are pending. */ //#define MK2_MULTIPLEXER

if ENABLED(MK2_MULTIPLEXER)

// Override the default DIO selector pins here, if needed. // Some pins files may provide defaults for these pins. //#define E_MUX0_PIN 40 // Always Required //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers

endif

// A dual extruder that uses a single stepper motor //#define SWITCHING_EXTRUDER

if ENABLED(SWITCHING_EXTRUDER)

define SWITCHING_EXTRUDER_SERVO_NR 0

define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]

if EXTRUDERS > 3

define SWITCHING_EXTRUDER_E23_SERVO_NR 1

endif

endif

// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles //#define SWITCHING_NOZZLE

if ENABLED(SWITCHING_NOZZLE)

define SWITCHING_NOZZLE_SERVO_NR 0

define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1

//#define HOTEND_OFFSET_Z { 0.0, 0.0 }

endif

/* Two separate X-carriages with extruders that connect to a moving part via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN. / //#define PARKING_EXTRUDER

if ENABLED(PARKING_EXTRUDER)

define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage

define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil

define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.

define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders

define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder

define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking

define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0.

endif

/**

// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis

// @section machine

/**

if POWER_SUPPLY > 0

// Enable this option to leave the PSU off at startup. // Power to steppers and heaters will need to be turned on with M80. //#define PS_DEFAULT_OFF

//#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin

if ENABLED(AUTO_POWER_CONTROL)

#define AUTO_POWER_FANS           // Turn on PSU if fans need power
#define AUTO_POWER_E_FANS
#define AUTO_POWER_CONTROLLERFAN
#define POWER_TIMEOUT 30

endif

endif

// @section temperature

//=========================================================================== //============================= Thermal Settings ============================ //===========================================================================

/**

define TEMP_SENSOR_0 11

if EXTRUDERS == 2

define TEMP_SENSOR_1 11

endif

define TEMP_SENSOR_2 0

define TEMP_SENSOR_3 0

define TEMP_SENSOR_4 0

define TEMP_SENSOR_BED 0

define TEMP_SENSOR_CHAMBER 0

// Dummy thermistor constant temperature readings, for use with 998 and 999

define DUMMY_THERMISTOR_998_VALUE 25

define DUMMY_THERMISTOR_999_VALUE 100

// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings // from the two sensors differ too much the print will be aborted. //#define TEMP_SENSOR_1_AS_REDUNDANT

define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5

// Extruder temperature must be close to target for this long before M109 returns success

define TEMP_RESIDENCY_TIME 10 // (seconds)

define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one

define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.

// Bed temperature must be close to target for this long before M190 returns success

define TEMP_BED_RESIDENCY_TIME 10 // (seconds)

define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one

define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.

// The minimal temperature defines the temperature below which the heater will not be enabled It is used // to check that the wiring to the thermistor is not broken. // Otherwise this would lead to the heater being powered on all the time.

define HEATER_0_MINTEMP 5

define HEATER_1_MINTEMP 5

define HEATER_2_MINTEMP 5

define HEATER_3_MINTEMP 5

define HEATER_4_MINTEMP 5

define BED_MINTEMP 5

// When temperature exceeds max temp, your heater will be switched off. // This feature exists to protect your hotend from overheating accidentally, but NOT from thermistor short/failure! // You should use MINTEMP for thermistor short/failure protection.

define HEATER_0_MAXTEMP 275

define HEATER_1_MAXTEMP 275

define HEATER_2_MAXTEMP 275

define HEATER_3_MAXTEMP 275

define HEATER_4_MAXTEMP 275

define BED_MAXTEMP 150

//=========================================================================== //============================= PID Settings ================================ //=========================================================================== // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning

// Comment the following line to disable PID and enable bang-bang.

define PIDTEMP

define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current

define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current

define PID_K1 0.95 // Smoothing factor within any PID loop

if ENABLED(PIDTEMP)

define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.

//#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) // Set/get with gcode: M301 E[extruder number, 0-2]

define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature

// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.

// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it

// Ultimaker //#define DEFAULT_Kp 22.2 //#define DEFAULT_Ki 1.08 //#define DEFAULT_Kd 114

// MakerGear //#define DEFAULT_Kp 7.0 //#define DEFAULT_Ki 0.1 //#define DEFAULT_Kd 12

// Mendel Parts V9 on 12V //#define DEFAULT_Kp 63.0 //#define DEFAULT_Ki 2.25 //#define DEFAULT_Kd 440

//E3D with 30MM fan

define DEFAULT_Kp 24.77

define DEFAULT_Ki 1.84

define DEFAULT_Kd 83.61

endif // PIDTEMP

//=========================================================================== //============================= PID > Bed Temperature Control =============== //===========================================================================

/**

//#define BED_LIMIT_SWITCHING

/**

if ENABLED(PIDTEMPBED)

//#define PID_BED_DEBUG // Sends debug data to the serial port.

//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) //#define DEFAULT_bedKp 10.00 //#define DEFAULT_bedKi .023 //#define DEFAULT_bedKd 305.4

//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune //#define DEFAULT_bedKp 97.1 //#define DEFAULT_bedKi 1.41 //#define DEFAULT_bedKd 1675.16

//D-force //#define DEFAULT_bedKp 22.97 //#define DEFAULT_bedKi 3.76 //#define DEFAULT_bedKd 29.2

// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.

endif // PIDTEMPBED

// @section extruder

/**

/**

//=========================================================================== //======================== Thermal Runaway Protection ======================= //===========================================================================

/**

define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders

// #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed

//=========================================================================== //============================= Mechanical Settings ========================= //===========================================================================

// @section machine

// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics // either in the usual order or reversed //#define COREXY //#define COREXZ //#define COREYZ //#define COREYX //#define COREZX //#define COREZY

//=========================================================================== //============================== Endstop Settings =========================== //===========================================================================

// @section homing

// Specify here all the endstop connectors that are connected to any endstop or probe. // Almost all printers will be using one per axis. Probes will use one or more of the // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.

define USE_XMIN_PLUG

define USE_YMIN_PLUG

define USE_ZMIN_PLUG

//#define USE_XMAX_PLUG //#define USE_YMAX_PLUG //#define USE_ZMAX_PLUG

// Enable pullup for all endstops to prevent a floating state

define ENDSTOPPULLUPS

if DISABLED(ENDSTOPPULLUPS)

// Disable ENDSTOPPULLUPS to set pullups individually //#define ENDSTOPPULLUP_XMAX //#define ENDSTOPPULLUP_YMAX //#define ENDSTOPPULLUP_ZMAX //#define ENDSTOPPULLUP_XMIN //#define ENDSTOPPULLUP_YMIN //#define ENDSTOPPULLUP_ZMIN //#define ENDSTOPPULLUP_ZMIN_PROBE

endif

// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).

define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.

define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.

define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.

define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.

define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.

define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.

define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.

/**

// Enable this feature if all enabled endstop pins are interrupt-capable. // This will remove the need to poll the interrupt pins, saving many CPU cycles. //#define ENDSTOP_INTERRUPTS_FEATURE

/**

//============================================================================= //============================== Movement Settings ============================ //============================================================================= // @section motion

/**

/**

/**

/**

/**

/**

//=========================================================================== //============================= Z Probe Options ============================= //=========================================================================== // @section probes

// // See http://marlinfw.org/docs/configuration/probes.html //

/**

/**

/**

/**

/**

/**

/**

// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE

// A sled-mounted probe like those designed by Charles Bell. //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

// // For Z_PROBE_ALLEN_KEY see the Delta example configurations. //

/**

// Certain types of probes need to stay away from edges

define MIN_PROBE_EDGE 10

// X and Y axis travel speed (mm/m) between probes

define XY_PROBE_SPEED 8000

// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)

define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z

// Feedrate (mm/m) for the "accurate" probe of each point

define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)

// The number of probes to perform at each point. // Set to 2 for a fast/slow probe, using the second probe result. // Set to 3 or more for slow probes, averaging the results. //#define MULTIPLE_PROBING 2

/**

define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping

// For M851 give a range for adjusting the Z probe offset

define Z_PROBE_OFFSET_RANGE_MIN -20

define Z_PROBE_OFFSET_RANGE_MAX 20

// Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST

// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' }

define X_ENABLE_ON 0

define Y_ENABLE_ON 0

define Z_ENABLE_ON 0

define E_ENABLE_ON 0 // For all extruders

// Disables axis stepper immediately when it's not being used. // WARNING: When motors turn off there is a chance of losing position accuracy!

define DISABLE_X false

define DISABLE_Y false

define DISABLE_Z false

// Warn on display about possibly reduced accuracy //#define DISABLE_REDUCED_ACCURACY_WARNING

// @section extruder

define DISABLE_E false // For all extruders

define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.

// @section machine

// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.

define INVERT_X_DIR true

define INVERT_Y_DIR true

define INVERT_Z_DIR false

// @section extruder

// For direct drive extruder v9 set to true, for geared extruder set to false.

define INVERT_E0_DIR false

define INVERT_E1_DIR false

define INVERT_E2_DIR false

define INVERT_E3_DIR false

define INVERT_E4_DIR false

// @section homing

//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed

//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.

define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...

                         // Be sure you have this distance over your Z_MAX_POS in case.

// Direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]

define X_HOME_DIR -1

define Y_HOME_DIR -1

define Z_HOME_DIR -1

// @section machine

// The size of the print bed

if EXTRUDERS > 1

define X_BED_SIZE 265

else

define X_BED_SIZE 290

endif

define Y_BED_SIZE 275

// Travel limits (mm) after homing, corresponding to endstop positions.

define X_MIN_POS 0

define Y_MIN_POS -15

define Z_MIN_POS 0

define X_MAX_POS X_BED_SIZE

define Y_MAX_POS Y_BED_SIZE

define Z_MAX_POS 220

/**

// Min software endstops constrain movement within minimum coordinate bounds //#define MIN_SOFTWARE_ENDSTOPS

if ENABLED(MIN_SOFTWARE_ENDSTOPS)

define MIN_SOFTWARE_ENDSTOP_X

define MIN_SOFTWARE_ENDSTOP_Y

define MIN_SOFTWARE_ENDSTOP_Z

endif

// Max software endstops constrain movement within maximum coordinate bounds

define MAX_SOFTWARE_ENDSTOPS

if ENABLED(MAX_SOFTWARE_ENDSTOPS)

define MAX_SOFTWARE_ENDSTOP_X

define MAX_SOFTWARE_ENDSTOP_Y

define MAX_SOFTWARE_ENDSTOP_Z

endif

if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)

define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD

endif

/**

//=========================================================================== //=============================== Bed Leveling ============================== //=========================================================================== // @section calibrate

/**

/**

/**

//#define DEBUG_LEVELING_FEATURE

if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)

// Gradually reduce leveling correction until a set height is reached, // at which point movement will be level to the machine's XY plane. // The height can be set with M420 Z

define ENABLE_LEVELING_FADE_HEIGHT

// For Cartesian machines, instead of dividing moves on mesh boundaries, // split up moves into short segments like a Delta. This follows the // contours of the bed more closely than edge-to-edge straight moves.

define SEGMENT_LEVELED_MOVES

define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)

/**

endif

if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)

// Set the number of grid points per dimension.

define GRID_MAX_POINTS_X 7

define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

// Set the boundaries for probing (where the probe can reach). //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - MIN_PROBE_EDGE) //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - MIN_PROBE_EDGE)

// Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST

if ENABLED(AUTO_BED_LEVELING_BILINEAR)

// Beyond the probed grid, continue the implied tilt?
// Default is to maintain the height of the nearest edge.
//#define EXTRAPOLATE_BEYOND_GRID

// // Experimental Subdivision of the grid by Catmull-Rom method. // Synthesizes intermediate points to produce a more detailed mesh. // //#define ABL_BILINEAR_SUBDIVISION

if ENABLED(ABL_BILINEAR_SUBDIVISION)

// Number of subdivisions between probe points

define BILINEAR_SUBDIVISIONS 3

endif

endif

elif ENABLED(AUTO_BED_LEVELING_UBL)

//=========================================================================== //========================= Unified Bed Leveling ============================ //===========================================================================

//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh

define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed

define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.

define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle

define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500

elif ENABLED(MESH_BED_LEVELING)

//=========================================================================== //=================================== Mesh ================================== //===========================================================================

define MESH_INSET 40 // Set Mesh bounds as an inset region of the bed

define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.

define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS

endif // BED_LEVELING

/**

/**

if ENABLED(LCD_BED_LEVELING)

define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.

define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment

endif

// Add a menu item to move between bed corners for manual bed adjustment //#define LEVEL_BED_CORNERS

if ENABLED(LEVEL_BED_CORNERS)

define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling

define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners

//#define LEVEL_CENTER_TOO // Move to the center after the last corner

endif

/**

// @section homing

// The center of the bed is at (X=0, Y=0) //#define BED_CENTER_AT_0_0

// Manually set the home position. Leave these undefined for automatic settings. // For DELTA this is the top-center of the Cartesian print volume.

define MANUAL_X_HOME_POS 0

define MANUAL_Y_HOME_POS 0

define MANUAL_Z_HOME_POS 0 // Distance between the nozzle to printbed after homing

// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. // // With this feature enabled: // // - Allow Z homing only after X and Y homing AND stepper drivers still enabled. // - If stepper drivers time out, it will need X and Y homing again before Z homing. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). // - Prevent Z homing when the Z probe is outside bed area. // //#define Z_SAFE_HOMING

if ENABLED(Z_SAFE_HOMING)

define Z_SAFE_HOMING_X_POINT 0 // X point for Z homing when homing all axes (G28).

define Z_SAFE_HOMING_Y_POINT 0 // Y point for Z homing when homing all axes (G28).

endif

// Homing speeds (mm/m)

define HOMING_FEEDRATE_XY 4000

define HOMING_FEEDRATE_Z 500

// @section calibrate

/**

if ENABLED(SKEW_CORRECTION)

// Input all length measurements here:

define XY_DIAG_AC 282.8427124746

define XY_DIAG_BD 282.8427124746

define XY_SIDE_AD 200

// Or, set the default skew factors directly here // to override the above measurements:

define XY_SKEW_FACTOR 0.0

//#define SKEW_CORRECTION_FOR_Z

if ENABLED(SKEW_CORRECTION_FOR_Z)

define XZ_DIAG_AC 282.8427124746

define XZ_DIAG_BD 282.8427124746

define YZ_DIAG_AC 282.8427124746

define YZ_DIAG_BD 282.8427124746

define YZ_SIDE_AD 200

define XZ_SKEW_FACTOR 0.0

define YZ_SKEW_FACTOR 0.0

endif

// Enable this option for M852 to set skew at runtime //#define SKEW_CORRECTION_GCODE

endif

//============================================================================= //============================= Additional Features =========================== //=============================================================================

// @section extras

// // EEPROM // // The microcontroller can store settings in the EEPROM, e.g. max velocity... // M500 - stores parameters in EEPROM // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. //

define EEPROM_SETTINGS // Enable for M500 and M501 commands

//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!

define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.

// // Host Keepalive // // When enabled Marlin will send a busy status message to the host // every couple of seconds when it can't accept commands. //

define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages

define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.

define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating

// // M100 Free Memory Watcher // //#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage

// // G20/G21 Inch mode support // //#define INCH_MODE_SUPPORT

// // M149 Set temperature units support // //#define TEMPERATURE_UNITS_SUPPORT

// @section temperature

// Preheat Constants

define PREHEAT_1_TEMP_HOTEND 180

define PREHEAT_1_TEMP_BED 70

define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255

define PREHEAT_2_TEMP_HOTEND 230

define PREHEAT_2_TEMP_BED 70

define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255

/**

if ENABLED(NOZZLE_PARK_FEATURE)

// Specify a park position as { X, Y, Z }

define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }

define NOZZLE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)

define NOZZLE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)

endif

/**

if ENABLED(NOZZLE_CLEAN_FEATURE)

// Default number of pattern repetitions

define NOZZLE_CLEAN_STROKES 12

// Default number of triangles

define NOZZLE_CLEAN_TRIANGLES 3

// Specify positions as { X, Y, Z }

define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}

define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}

// Circular pattern radius

define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5

// Circular pattern circle fragments number

define NOZZLE_CLEAN_CIRCLE_FN 10

// Middle point of circle

define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT

// Moves the nozzle to the initial position

define NOZZLE_CLEAN_GOBACK

endif

/**

/**

//============================================================================= //============================= LCD and SD support ============================ //=============================================================================

// @section lcd

/**

/**

/**

/**

/**

/**

// // ENCODER SETTINGS // // This option overrides the default number of encoder pulses needed to // produce one step. Should be increased for high-resolution encoders. // //#define ENCODER_PULSES_PER_STEP 4

// // Use this option to override the number of step signals required to // move between next/prev menu items. // //#define ENCODER_STEPS_PER_MENU_ITEM 1

/**

// // This option reverses the encoder direction everywhere. // // Set this option if CLOCKWISE causes values to DECREASE //

define REVERSE_ENCODER_DIRECTION

// // This option reverses the encoder direction for navigating LCD menus. // // If CLOCKWISE normally moves DOWN this makes it go UP. // If CLOCKWISE normally moves UP this makes it go DOWN. // //#define REVERSE_MENU_DIRECTION

// // Individual Axis Homing // // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. // //#define INDIVIDUAL_AXIS_HOMING_MENU

// // SPEAKER/BUZZER // // If you have a speaker that can produce tones, enable it here. // By default Marlin assumes you have a buzzer with a fixed frequency. // //#define SPEAKER

// // The duration and frequency for the UI feedback sound. // Set these to 0 to disable audio feedback in the LCD menus. // // Note: Test audio output with the G-Code: // M300 S P //

define LCD_FEEDBACK_FREQUENCY_DURATION_MS 1

define LCD_FEEDBACK_FREQUENCY_HZ 1000

//============================================================================= //======================== LCD / Controller Selection ========================= //======================== (Character-based LCDs) ========================= //=============================================================================

// // RepRapDiscount Smart Controller. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller // // Note: Usually sold with a white PCB. // //#define REPRAP_DISCOUNT_SMART_CONTROLLER

// // ULTIMAKER Controller. // //#define ULTIMAKERCONTROLLER

// // ULTIPANEL as seen on Thingiverse. // //#define ULTIPANEL

// // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) // http://reprap.org/wiki/PanelOne // //#define PANEL_ONE

// // GADGETS3D G3D LCD/SD Controller // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel // // Note: Usually sold with a blue PCB. // //#define G3D_PANEL

// // RigidBot Panel V1.0 // http://www.inventapart.com/ // //#define RIGIDBOT_PANEL

// // Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller // https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html // //#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602

// // ANET and Tronxy 20x4 Controller // //#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. // This LCD is known to be susceptible to electrical interference // which scrambles the display. Pressing any button clears it up. // This is a LCD2004 display with 5 analog buttons.

// // Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. // //#define ULTRA_LCD

//============================================================================= //======================== LCD / Controller Selection ========================= //===================== (I2C and Shift-Register LCDs) ===================== //=============================================================================

// // CONTROLLER TYPE: I2C // // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C //

// // Elefu RA Board Control Panel // http://www.elefu.com/index.php?route=product/product&product_id=53 // //#define RA_CONTROL_PANEL

// // Sainsmart (YwRobot) LCD Displays // // These require F.Malpartida's LiquidCrystal_I2C library // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home // //#define LCD_SAINSMART_I2C_1602 //#define LCD_SAINSMART_I2C_2004

// // Generic LCM1602 LCD adapter // //#define LCM1602

// // PANELOLU2 LCD with status LEDs, // separate encoder and click inputs. // // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. // For more info: https://github.com/lincomatic/LiquidTWI2 // // Note: The PANELOLU2 encoder click input can either be directly connected to // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). // //#define LCD_I2C_PANELOLU2

// // Panucatt VIKI LCD with status LEDs, // integrated click & L/R/U/D buttons, separate encoder inputs. // //#define LCD_I2C_VIKI

// // CONTROLLER TYPE: Shift register panels //

// // 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD // //#define SAV_3DLCD

//============================================================================= //======================= LCD / Controller Selection ======================= //========================= (Graphical LCDs) ======================== //=============================================================================

// // CONTROLLER TYPE: Graphical 128x64 (DOGM) // // IMPORTANT: The U8glib library is required for Graphical Display! // https://github.com/olikraus/U8glib_Arduino //

// // RepRapDiscount FULL GRAPHIC Smart Controller // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller //

define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER

// ReprapWorld Graphical LCD // https://reprapworld.com/?products_details&products_id/1218 // //#define REPRAPWORLD_GRAPHICAL_LCD

// // Activate one of these if you have a Panucatt Devices // Viki 2.0 or mini Viki with Graphic LCD // http://panucatt.com // //#define VIKI2 //#define miniVIKI

// // MakerLab Mini Panel with graphic // controller and SD support - http://reprap.org/wiki/Mini_panel // //#define MINIPANEL

// // MaKr3d Makr-Panel with graphic controller and SD support. // http://reprap.org/wiki/MaKr3d_MaKrPanel // //#define MAKRPANEL

// // Adafruit ST7565 Full Graphic Controller. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ // //#define ELB_FULL_GRAPHIC_CONTROLLER

// // BQ LCD Smart Controller shipped by // default with the BQ Hephestos 2 and Witbox 2. // //#define BQ_LCD_SMART_CONTROLLER

// // Cartesio UI // http://mauk.cc/webshop/cartesio-shop/electronics/user-interface // //#define CARTESIO_UI

// // LCD for Melzi Card with Graphical LCD // //#define LCD_FOR_MELZI

// // SSD1306 OLED full graphics generic display // //#define U8GLIB_SSD1306

// // SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules // //#define SAV_3DGLCD

if ENABLED(SAV_3DGLCD)

//#define U8GLIB_SSD1306

define U8GLIB_SH1106

endif

// // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER

// // TinyBoy2 128x64 OLED / Encoder Panel // //#define OLED_PANEL_TINYBOY2

// // MKS MINI12864 with graphic controller and SD support // http://reprap.org/wiki/MKS_MINI_12864 // //#define MKS_MINI_12864

// // Factory display for Creality CR-10 // https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html // // This is RAMPS-compatible using a single 10-pin connector. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display) // //#define CR10_STOCKDISPLAY

// // ANET and Tronxy Graphical Controller // //#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 // A clone of the RepRapDiscount full graphics display but with // different pins/wiring (see pins_ANET_10.h).

// // MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER // http://reprap.org/wiki/MKS_12864OLED // // Tiny, but very sharp OLED display // //#define MKS_12864OLED // Uses the SH1106 controller (default) //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller

// // Silvergate GLCD controller // http://github.com/android444/Silvergate // //#define SILVER_GATE_GLCD_CONTROLLER

//============================================================================= //============================ Other Controllers ============================ //=============================================================================

// // CONTROLLER TYPE: Standalone / Serial //

// // LCD for Malyan M200 printers. // This requires SDSUPPORT to be enabled // //#define MALYAN_LCD

// // CONTROLLER TYPE: Keypad / Add-on //

// // RepRapWorld REPRAPWORLD_KEYPAD v1.1 // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 // // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key // is pressed, a value of 10.0 means 10mm per click. // //#define REPRAPWORLD_KEYPAD //#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0

//============================================================================= //=============================== Extra Features ============================== //=============================================================================

// @section extras

// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino //#define FAST_PWM_FAN

// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency // which is not as annoying as with the hardware PWM. On the other hand, if this frequency // is too low, you should also increment SOFT_PWM_SCALE. //#define FAN_SOFT_PWM

// Incrementing this by 1 will double the software PWM frequency, // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. // However, control resolution will be halved for each increment; // at zero value, there are 128 effective control positions.

define SOFT_PWM_SCALE 0

// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can // be used to mitigate the associated resolution loss. If enabled, // some of the PWM cycles are stretched so on average the desired // duty cycle is attained. //#define SOFT_PWM_DITHER

// Temperature status LEDs that display the hotend and bed temperature. // If all hotends, bed temperature, and target temperature are under 54C // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) //#define TEMP_STAT_LEDS

// M240 Triggers a camera by emulating a Canon RC-1 Remote // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ //#define PHOTOGRAPH_PIN 23

// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure //#define SF_ARC_FIX

// Support for the BariCUDA Paste Extruder //#define BARICUDA

// Support for BlinkM/CyzRgb //#define BLINKM

// Support for PCA9632 PWM LED driver //#define PCA9632

/**

if ENABLED(RGB_LED) || ENABLED(RGBW_LED)

define RGB_LED_R_PIN 34

define RGB_LED_G_PIN 43

define RGB_LED_B_PIN 35

define RGB_LED_W_PIN -1

endif

// Support for Adafruit Neopixel LED driver //#define NEOPIXEL_LED

if ENABLED(NEOPIXEL_LED)

define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)

define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)

define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip

define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.

define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)

//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup

endif

/**

/**

/**

// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // 300ms is a good value but you can try less delay. // If the servo can't reach the requested position, increase it.

define SERVO_DELAY { 300 }

// Only power servos during movement, otherwise leave off to prevent jitter //#define DEACTIVATE_SERVOS_AFTER_MOVE

endif // CONFIGURATION_H

ryanhmonument commented 5 years ago

i thank you for your reply.. i in the meantime went and bought the mks sbase and installed smoothieware, and had everything up and running nicely, i was making some minor tweeks to the tft screen as i was having trouble running with out the sdcard in the main boards socket, and it was not making the cusor files, so i figured i would get a new firmware.bin and reflash it, as soon as i updated the firmware, that was all she wrote, i've been a week of testing and tweeking and can not get anything to talk to the main board, all the lights are doing what they should, the config looks the same as when it was running fine, so i'm going to try throwing your marlin config at this rumba board to get it making noise.. and get my 12 yr old daughter who's now loosing interest back up and running, then i can play with tweeking something to get the smoothie and touch screen up and turning motor's.. Ryan HoganWarren Monument Co.55 Railroad Ave.Warren RI 02885Phone (401)245-9194fax (401)247-1104

-------- Original Message -------- Subject: Re: [bigtreetech/Tango-3D-Printer-Motherboard] MARLIN ISSUES (#3) From: jimhiggs notifications@github.com Date: Thu, February 14, 2019 3:10 pm To: bigtreetech/Tango-3D-Printer-Motherboard Tango-3D-Printer-Motherboard@noreply.github.com Cc: ryanhmonument ryan@warrenmonument.com, Author author@noreply.github.com

I downloaded the stock Marlin 1.1.9 firmware and started from there. You are welcome to try my conf file. Mine is a modified cubex wth E3d hotends, no hotbed heater, raising bed Z azis and all endstops set for top, left, rear as 0,0,0 and I then use gcode to center 0,0,0 at center of bed. / Marlin 3D Printer Firmware Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] Based on Sprinter and grbl. Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/. */ /* Configuration.h Basic settings such as: Type of electronics Type of temperature sensor Printer geometry Endstop configuration LCD controller Extra features Advanced settings can be found in Configuration_adv.h / #ifndef CONFIGURATION_H #define CONFIGURATION_H #define CONFIGURATION_H_VERSION 010109 //=========================================================================== //============================= Getting Started ============================= //=========================================================================== / Here are some standard links for getting your machine calibrated: http://reprap.org/wiki/Calibration http://youtu.be/wAL9d7FgInk http://calculator.josefprusa.cz http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide http://www.thingiverse.com/thing:5573 https://sites.google.com/site/repraplogphase/calibration-of-your-reprap http://www.thingiverse.com/thing:298812 / //=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== // For a Delta printer start with one of the configuration files in the // example_configurations/delta directory and customize for your machine. // //=========================================================================== //============================= SCARA Printer =============================== //=========================================================================== // For a SCARA printer start with the configuration files in // example_configurations/SCARA and customize for your machine. // // @Section info // User-specified version info of this build to display in [Pronterface, etc] terminal window during // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this // build by the user have been successfully uploaded into firmware. #define STRING_CONFIG_H_AUTHOR "Me" // Who made the changes. //#define SHOW_BOOTSCREEN //#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 //#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 / VENDORS PLEASE READ Marlin allows you to add a custom boot image for Graphical LCDs. With this option Marlin will first show your custom screen followed by the standard Marlin logo with version number and web URL. We encourage you to take advantage of this new feature and we also respectfully request that you retain the unmodified Marlin boot screen. / // Enable to show the bitmap in Marlin/_Bootscreen.h on startup. //#define SHOW_CUSTOM_BOOTSCREEN // Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. //#define CUSTOM_STATUS_SCREEN_IMAGE // @Section machine / Select the serial port on the board to use for communication with the host. This allows the connection of wireless adapters (for instance) to non-default port pins. Serial port 0 is always used by the Arduino bootloader regardless of this setting. :[0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 / This setting determines the communication speed of the printer. 250000 works in most cases, but you might try a lower speed if you commonly experience drop-outs during host printing. You may try up to 1000000 to speed up SD file transfer. :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] */ #define BAUDRATE 115200 // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH // The following define selects which electronics board you have. // Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RUMBA #endif // Optional custom name for your RepStrap or other custom machine // Displayed in the LCD "Ready" message #define CUSTOM_MACHINE_NAME "Reprap Cubex" // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @Section extruder // This defines the number of extruders // :[1, 2, 3, 4, 5] #define EXTRUDERS 1 // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // For Cyclops or any "multi-extruder" that shares a single nozzle. //#define SINGLENOZZLE /* Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. This device allows one stepper driver on a control board to drive two to eight stepper motors, one at a time, in a manner suitable for extruders. This option only allows the multiplexer to switch on tool-change. Additional options to configure custom E moves are pending. / //#define MK2_MULTIPLEXER #if ENABLED(MK2_MULTIPLEXER) // Override the default DIO selector pins here, if needed. // Some pins files may provide defaults for these pins. //#define E_MUX0_PIN 40 // Always Required //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers #endif // A dual extruder that uses a single stepper motor //#define SWITCHING_EXTRUDER #if ENABLED(SWITCHING_EXTRUDER) #define SWITCHING_EXTRUDER_SERVO_NR 0 #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] #if EXTRUDERS > 3 #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 #endif #endif // A dual-nozzle that uses a servomotor to raise/lower one of the nozzles //#define SWITCHING_NOZZLE #if ENABLED(SWITCHING_NOZZLE) #define SWITCHING_NOZZLE_SERVO_NR 0 #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 //#define HOTEND_OFFSET_Z { 0.0, 0.0 } #endif / Two separate X-carriages with extruders that connect to a moving part via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN. */ //#define PARKING_EXTRUDER #if ENABLED(PARKING_EXTRUDER) #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined. #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0. #endif / "Mixing Extruder" Adds G-codes M163 and M164 to set and "commit" the current mix factors. Extends the stepping routines to move multiple steppers in proportion to the mix. Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. This implementation supports up to two mixing extruders. Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). */ //#define MIXING_EXTRUDER #if ENABLED(MIXING_EXTRUDER) #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands #endif // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis // @Section machine /* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN 0 = No Power Switch 1 = ATX 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } / #define POWER_SUPPLY 0 #if POWER_SUPPLY > 0 // Enable this option to leave the PSU off at startup. // Power to steppers and heaters will need to be turned on with M80. //#define PS_DEFAULT_OFF //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin #if ENABLED(AUTO_POWER_CONTROL) #define AUTO_POWER_FANS // Turn on PSU if fans need power #define AUTO_POWER_E_FANS #define AUTO_POWER_CONTROLLERFAN #define POWER_TIMEOUT 30 #endif #endif // @Section temperature //=========================================================================== //============================= Thermal Settings ============================ //=========================================================================== / --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table Temperature sensors available: -4 : thermocouple with AD8495 -3 : thermocouple with MAX31855 (only for sensor 0) -2 : thermocouple with MAX6675 (only for sensor 0) -1 : thermocouple with AD595 0 : not used 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) 3 : Mendel-parts thermistor (4.7k pullup) 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) 501 : 100K Zonestar (Tronxy X3A) Thermistor 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) 10 : 100k RS thermistor 198-961 (4.7k pullup) 11 : 100k beta 3950 1% thermistor (4.7k pullup) 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" 15 : 100k thermistor calibration for JGAurora A5 hotend 20 : the PT100 circuit found in the Ultimainboard V2.x 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 66 : 4.7M High Temperature thermistor from Dyze Design 70 : the 100K thermistor found in the bq Hephestos 2 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. (but gives greater accuracy and more stable PID) 51 : 100k thermistor - EPCOS (1k pullup) 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) 1047 : Pt1000 with 4k7 pullup 1010 : Pt1000 with 1k pullup (non standard) 147 : Pt100 with 4k7 pullup 110 : Pt100 with 1k pullup (non standard) Use these for Testing or Development purposes. NEVER for production machine. 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } */ #define TEMP_SENSOR_0 11 #if EXTRUDERS == 2 #define TEMP_SENSOR_1 11 #endif #define TEMP_SENSOR_2 0 #define TEMP_SENSOR_3 0 #define TEMP_SENSOR_4 0 #define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_CHAMBER 0 // Dummy thermistor constant temperature readings, for use with 998 and 999 #define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_999_VALUE 100 // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings // from the two sensors differ too much the print will be aborted. //#define TEMP_SENSOR_1_AS_REDUNDANT #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 // Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. // Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. // The minimal temperature defines the temperature below which the heater will not be enabled It is used // to check that the wiring to the thermistor is not broken. // Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5 #define BED_MINTEMP 5 // When temperature exceeds max temp, your heater will be switched off. // This feature exists to protect your hotend from overheating accidentally, but NOT from thermistor short/failure! // You should use MINTEMP for thermistor short/failure protection. #define HEATER_0_MAXTEMP 275 #define HEATER_1_MAXTEMP 275 #define HEATER_2_MAXTEMP 275 #define HEATER_3_MAXTEMP 275 #define HEATER_4_MAXTEMP 275 #define BED_MAXTEMP 150 //=========================================================================== //============================= PID Settings ================================ //=========================================================================== // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning // Comment the following line to disable PID and enable bang-bang. #define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop #if ENABLED(PIDTEMP) #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Ultimaker //#define DEFAULT_Kp 22.2 //#define DEFAULT_Ki 1.08 //#define DEFAULT_Kd 114 // MakerGear //#define DEFAULT_Kp 7.0 //#define DEFAULT_Ki 0.1 //#define DEFAULT_Kd 12 // Mendel Parts V9 on 12V //#define DEFAULT_Kp 63.0 //#define DEFAULT_Ki 2.25 //#define DEFAULT_Kd 440 //E3D with 30MM fan #define DEFAULT_Kp 24.77 #define DEFAULT_Ki 1.84 #define DEFAULT_Kd 83.61 #endif // PIDTEMP //=========================================================================== //============================= PID > Bed Temperature Control =============== //=========================================================================== / PID Bed Heating If this option is enabled set PID constants below. If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. The PID frequency will be the same as the extruder PWM. If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, which is fine for driving a square wave into a resistive load and does not significantly impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. If your configuration is significantly different than this and you don't understand the issues involved, don't use bed PID until someone else verifies that your hardware works. */ //#define PIDTEMPBED //#define BED_LIMIT_SWITCHING /* Max Bed Power Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). When set to any value below 255, enables a form of PWM to the bed that acts like a divider so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) / #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) //#define DEFAULT_bedKp 10.00 //#define DEFAULT_bedKi .023 //#define DEFAULT_bedKd 305.4 //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune //#define DEFAULT_bedKp 97.1 //#define DEFAULT_bedKi 1.41 //#define DEFAULT_bedKd 1675.16 //D-force //#define DEFAULT_bedKp 22.97 //#define DEFAULT_bedKi 3.76 //#define DEFAULT_bedKd 29.2 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED // @Section extruder / Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. Add M302 to set the minimum extrusion temperature and/or turn cold extrusion prevention on and off. IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! */ #define PREVENT_COLD_EXTRUSION #define EXTRUDE_MINTEMP 170 / Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. Note: For Bowden Extruders make this large enough to allow load/unload. */ #define PREVENT_LENGTHY_EXTRUDE #define EXTRUDE_MAXLENGTH 300 //=========================================================================== //======================== Thermal Runaway Protection ======================= //=========================================================================== /* Thermal Protection provides additional protection to your printer from damage and fire. Marlin always includes safe min and max temperature ranges which protect against a broken or disconnected thermistor wire. The issue: If a thermistor falls out, it will report the much lower temperature of the air in the room, and the the firmware will keep the heater on. If you get "Thermal Runaway" or "Heating failed" errors the details can be tuned in Configuration_adv.h / #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders // #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed //=========================================================================== //============================= Mechanical Settings ========================= //=========================================================================== // @Section machine // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics // either in the usual order or reversed //#define COREXY //#define COREXZ //#define COREYZ //#define COREYX //#define COREZX //#define COREZY //=========================================================================== //============================== Endstop Settings =========================== //=========================================================================== // @Section homing // Specify here all the endstop connectors that are connected to any endstop or probe. // Almost all printers will be using one per axis. Probes will use one or more of the // extra connectors. Leave undefined any used for non-endstop and non-probe purposes. #define USE_XMIN_PLUG #define USE_YMIN_PLUG #define USE_ZMIN_PLUG //#define USE_XMAX_PLUG //#define USE_YMAX_PLUG //#define USE_ZMAX_PLUG // Enable pullup for all endstops to prevent a floating state #define ENDSTOPPULLUPS #if DISABLED(ENDSTOPPULLUPS) // Disable ENDSTOPPULLUPS to set pullups individually //#define ENDSTOPPULLUP_XMAX //#define ENDSTOPPULLUP_YMAX //#define ENDSTOPPULLUP_ZMAX //#define ENDSTOPPULLUP_XMIN //#define ENDSTOPPULLUP_YMIN //#define ENDSTOPPULLUP_ZMIN //#define ENDSTOPPULLUP_ZMIN_PROBE #endif // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). #define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. #define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. #define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. #define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. #define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. #define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. #define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe. / Stepper Drivers These settings allow Marlin to tune stepper driver timing and enable advanced options for stepper drivers that support them. You may also override timing options in Configuration_adv.h. A4988 is assumed for unspecified drivers. Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE, TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, TMC5130, TMC5130_STANDALONE :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE'] */ #define X_DRIVER_TYPE DRV8825 #define Y_DRIVER_TYPE DRV8825 #define Z_DRIVER_TYPE DRV8825 //#define X2_DRIVER_TYPE DRV8825 #define Y2_DRIVER_TYPE DRV8825 //#define Z2_DRIVER_TYPE DRV8825 #define E0_DRIVER_TYPE DRV8825 #define E1_DRIVER_TYPE DRV8825 //#define E2_DRIVER_TYPE DRV8825 //#define E3_DRIVER_TYPE DRV8825 //#define E4_DRIVER_TYPE DRV8825 // Enable this feature if all enabled endstop pins are interrupt-capable. // This will remove the need to poll the interrupt pins, saving many CPU cycles. //#define ENDSTOP_INTERRUPTS_FEATURE / Endstop Noise Filter Enable this option if endstops falsely trigger due to noise. NOTE: Enabling this feature means adds an error of +/-0.2mm, so homing will end up at a slightly different position on each G28. This will also reduce accuracy of some bed probes. For mechanical switches, the better approach to reduce noise is to install a 100 nanofarads ceramic capacitor in parallel with the switch, making it essentially noise-proof without sacrificing accuracy. This option also increases MCU load when endstops or the probe are enabled. So this is not recommended. USE AT YOUR OWN RISK. (This feature is not required for common micro-switches mounted on PCBs based on the Makerbot design, since they already include the 100nF capacitor.) */ //#define ENDSTOP_NOISE_FILTER //============================================================================= //============================== Movement Settings ============================ //============================================================================= // @Section motion /* Default Settings These settings can be reset by M502 Note that if EEPROM is enabled, saved values will override these. / / With this option each E stepper can have its own factors for the following movement settings. If fewer factors are given than the total number of extruders, the last value applies to the rest. */ //#define DISTINCT_E_FACTORS / Default Axis Steps Per Unit (steps/mm) Override with M92 X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] / #define DEFAULT_AXIS_STEPS_PER_UNIT {175.5,175.5,2143.4,165} / Default Max Feed Rate (mm/s) Override with M203 X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] / #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } / Default Max Acceleration (change/s) change = mm/s (Maximum start speed for accelerated moves) Override with M201 X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] */ #define DEFAULT_MAX_ACCELERATION { 400, 400, 100, 500 } / Default Acceleration (change/s) change = mm/s Override with M204 M204 P Acceleration M204 R Retract Acceleration M204 T Travel Acceleration */ #define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration for printing moves #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration for travel (non printing) moves / Default Jerk (mm/s) Override with M205 X Y Z E "Jerk" specifies the minimum speed change that requires acceleration. When changing speed and direction, if the difference is less than the value set here, it may happen instantaneously. / #define DEFAULT_XJERK 3.0 #define DEFAULT_YJERK DEFAULT_XJERK #define DEFAULT_ZJERK 0.4 // Must be same as XY for delta #define DEFAULT_EJERK 4.0 / S-Curve Acceleration This option eliminates vibration during printing by fitting a Bézier curve to move acceleration, producing much smoother direction changes. See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained / //#define S_CURVE_ACCELERATION //=========================================================================== //============================= Z Probe Options ============================= //=========================================================================== // @Section probes // // See http://marlinfw.org/docs/configuration/probes.html // / Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN Enable this option for a probe connected to the Z Min endstop pin. */ //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN / Z_MIN_PROBE_ENDSTOP Enable this option for a probe connected to any pin except Z-Min. (By default Marlin assumes the Z-Max endstop pin.) To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below. The simplest option is to use a free endstop connector. Use 5V for powered (usually inductive) sensors. RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: For simple switches connect... - normally-closed switches to GND and D32.

jimhiggs commented 5 years ago

There is a lot of customisation in my file. You might be better off starting with the basic marlin off github, and make sure you change the board type to Rumba so it picks up the correct pin outs. I have since updated to marlin 2.0 bugfix version and it runs fine.

jimhiggs commented 5 years ago

The other thing is sign up for the reprap forums you will get much more help than on here and there are a lot of guys a lot smarter than me when it comes to boards and marlin config issues.

Dloranger commented 5 years ago

I just posted my entire marlin folder to the other bug report, this is configured for an ANET A8 (frame only at this point) TRI COLOR (diamond) with a touch probe. down to one issue on the extruder 1 but that likely won't impact you.

if you got it working, be sure to close this bug report

ryanhmonument commented 5 years ago

awesome i'll get that uploaded to my board this weekend., and i'll let you know how i make out.Ryan HoganWarren Monument Co.55 Railroad Ave.Warren RI 02885Phone (401)245-9194fax (401)247-1104

-------- Original Message -------- Subject: Re: [bigtreetech/Tango-3D-Printer-Motherboard] MARLIN ISSUES (#3) From: Daniel Loranger notifications@github.com Date: Thu, February 28, 2019 11:30 am To: bigtreetech/Tango-3D-Printer-Motherboard Tango-3D-Printer-Motherboard@noreply.github.com Cc: ryanhmonument ryan@warrenmonument.com, Author author@noreply.github.com

I just posted my entire marlin folder to the other bug report, this is configured for an ANET A8 (frame only at this point) TRI COLOR (diamond) with a touch probe. down to one issue on the extruder 1 but that likely won't impact you. if you got it working, be sure to close this bug report —You are receiving this because you authored the thread.Reply to this email directly, view it on GitHub, or mute the thread.

Dloranger commented 5 years ago

hopefully it will get you back online,

I expect you will still need to tweak a bit things like disabling the touch probe, change the LCD type, extruder count, mxing hotend, end-stop locations, etc, but at a minimum you should be able to load it up and get some basic signs of life from the board to get going.

Dloranger commented 5 years ago

Okay, everything is working on my end now, the motor thing is a bug in the lcd interface.

On Thu, Feb 28, 2019, 9:30 AM ryanhmonument notifications@github.com wrote:

awesome i'll get that uploaded to my board this weekend., and i'll let you know how i make out.Ryan HoganWarren Monument Co.55 Railroad Ave.Warren RI 02885Phone (401)245-9194fax (401)247-1104

-------- Original Message -------- Subject: Re: [bigtreetech/Tango-3D-Printer-Motherboard] MARLIN ISSUES (#3) From: Daniel Loranger notifications@github.com Date: Thu, February 28, 2019 11:30 am To: bigtreetech/Tango-3D-Printer-Motherboard Tango-3D-Printer-Motherboard@noreply.github.com Cc: ryanhmonument ryan@warrenmonument.com, Author author@noreply.github.com

I just posted my entire marlin folder to the other bug report, this is configured for an ANET A8 (frame only at this point) TRI COLOR (diamond) with a touch probe. down to one issue on the extruder 1 but that likely won't impact you. if you got it working, be sure to close this bug report —You are receiving this because you authored the thread.Reply to this email directly, view it on GitHub, or mute the thread.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/Tango-3D-Printer-Motherboard/issues/3#issuecomment-468362957, or mute the thread https://github.com/notifications/unsubscribe-auth/AJ6NjVLUC81M7DM3uknnblW0qld7kIpXks5vSBI0gaJpZM4aytUz .

lacchinig commented 5 years ago

Hi, I have bought a Tango board with reprap 12864 LCD. When I tried to install Marlin 1.1.9 the screen appear corrupted. I have not identified the issue, just go back to 1.1.8 Any idea?

Dloranger commented 5 years ago

Possibly your 5V is not actually 5V?

I saw the power supply drop when powered over usb with the lcd installed. I had to wire it up for 13V same as the printer. This might have been the ramps board I had before, but worth checking.

I think there is a jumper for this on the bottom left if I recall. I havent had to touch mine since I set it up

lacchinig commented 5 years ago

Maybe, but using the 1.1.8 taken from Github Tango board page all work fine. Into the ".ino" file it call biqu.h file... Could be something different? One more point is it is called watchdog.h, I don't see the same for 1.1.9 version.