brandond / esphome-tuya_pir

ESPHome support for cheap WiFi PIR sensors
66 stars 21 forks source link

Stuck in a boot loop #10

Open ollieatkinson opened 4 years ago

ollieatkinson commented 4 years ago

ESPHome version: 1.14.3

I installed through using the steps in the README with success and have been able to update the firmware on the device and see it connected to my network.

The device is now stuck in an loop, as can be seen from the log taken from the device below:

INFO Successfully connected to 10.10.26.81
[20:35:14][C][adc:026]: ADC Sensor 'PIR Battery'
[20:35:14][C][adc:026]:   Unit of Measurement: 'V'
[20:35:14][C][adc:026]:   Accuracy Decimals: 2
[20:35:14][C][adc:026]:   Icon: 'mdi:flash'
[20:35:14][C][adc:029]:   Pin: VCC
[20:35:14][C][adc:051]:   Update Interval: 4294967.5s
[20:35:14][C][ota:029]: Over-The-Air Updates:
[20:35:14][C][ota:030]:   Address: 10.10.26.81:8266
[20:35:14][C][api:095]: API Server:
[20:35:14][C][api:096]:   Address: 10.10.26.81:6053
[20:35:14][C][mqtt:051]: MQTT:
[20:35:14][C][mqtt:053]:   Server Address: 10.10.26.67:1883 (10.10.26.67)
[20:35:14][C][mqtt:054]:   Username: 

[redacted]
[20:35:14][C][mqtt:055]:   Client ID: 

[redacted]
[20:35:14][C][mqtt:060]:   Topic Prefix: 'pir'
[20:35:14][C][mqtt:062]:   Log Topic: 'pir/debug'
[20:35:14][C][sb1:242]: SB1 UART:
[20:35:14][C][sb1:243]:   Boot Mode: NORMAL
[20:35:14][C][sb1:244]:   Product Info: {"p":"Okurono2XLVRV0fB","v":"1.0.2","m":0}
[20:35:14][C][wifi_signal.sensor:009]: WiFi Signal 'PIR WiFi Signal'
[20:35:14][C][wifi_signal.sensor:009]:   Unit of Measurement: 'dB'
[20:35:14][C][wifi_signal.sensor:009]:   Accuracy Decimals: 0
[20:35:14][C][wifi_signal.sensor:009]:   Icon: 'mdi:wifi'
[20:35:14][C][mqtt.sensor:024]: MQTT Sensor 'PIR WiFi Signal':
[20:35:14][C][mqtt.sensor:028]:   State Topic: 'pir/sensor/pir_wifi_signal/state'
[20:35:14][C][mqtt.sensor:024]: MQTT Sensor 'PIR Battery':
[20:35:14][C][mqtt.sensor:028]:   State Topic: 'pir/sensor/pir_battery/state'
[20:35:14][C][mqtt.binary_sensor:018]: MQTT Binary Sensor 'PIR Motion':
[20:35:14][C][mqtt.binary_sensor:019]:   State Topic: 'pir/binary_sensor/pir_motion/state'
[20:35:14][D][sb1:350]: Event message of length 5
[20:35:14][D][sb1:352]: 00: 0x66
[20:35:14][D][sb1:352]: 01: 0x04
[20:35:14][D][sb1:352]: 02: 0x00
[20:35:14][D][sb1:352]: 03: 0x01
[20:35:14][D][sb1:352]: 04: 0x00
[20:35:14][I][sb1:370]: Reset event: 0
[20:35:14][D][sb1:185]: state: 15 -> 13 after 417 ms
[20:35:15][I][sb1:343]: Rebooting: SB1_STATE_EVENT_ACK
[20:35:15][I][app:137]: Rebooting safely...
[20:35:15][D][sb1:392]: SB1 UART shutting down; next boot mode NORMAL
INFO Connecting to 10.10.26.81:6053 (10.10.26.81)
[20:35:47][I][mqtt:202]: MQTT Connected!
[20:35:47][D][sb1:185]: state: 10 -> 11 after 201 ms
[20:35:47][I][app:058]: setup() finished successfully!
[20:35:47][I][app:100]: ESPHome version 1.14.3 compiled on Jan 12 2020, 20:31:54
[20:35:47][C][wifi:415]: WiFi:
[20:35:47][C][wifi:283]:   SSID: 

[redacted]
[20:35:47][C][wifi:284]:   IP Address: 10.10.26.81
[20:35:47][C][wifi:286]:   BSSID: 

[redacted]
[20:35:47][C][wifi:287]:   Hostname: 'pir'
[20:35:47][C][wifi:291]:   Signal strength: -32 dB ▂▄▆█
[20:35:47][C][wifi:295]:   Channel: 6
[20:35:47][C][wifi:296]:   Subnet: 255.255.255.0
[20:35:47][C][wifi:297]:   Gateway: 10.10.26.1
[20:35:47][C][wifi:298]:   DNS1: (IP unset)
[20:35:47][C][wifi:299]:   DNS2: (IP unset)
[20:35:47][D][sb1:185]: state: 11 -> 15 after 71 ms
[20:35:47][C][uart:140]: UART Bus:
[20:35:47][C][uart:142]:   TX Pin: GPIO1
[20:35:47][C][uart:145]:   RX Pin: GPIO3
[20:35:47][C][uart:147]:   Baud Rate: 9600 baud
[20:35:47][C][uart:148]:   Stop bits: 1
[20:35:47][C][uart:150]:   Using hardware serial interface.
[20:35:47][C][template.binary_sensor:018]: Template Binary Sensor 'PIR Motion'
[20:35:47][C][template.binary_sensor:018]:   Device Class: 'motion'
[20:35:47][C][logger:175]: Logger:
[20:35:47][C][logger:176]:   Level: DEBUG
[20:35:47][C][logger:177]:   Log Baud Rate: 115200
[20:35:47][C][logger:178]:   Hardware UART: UART1
[20:35:47][C][adc:026]: ADC Sensor 'PIR Battery'
[20:35:47][C][adc:026]:   Unit of Measurement: 'V'
[20:35:47][C][adc:026]:   Accuracy Decimals: 2
[20:35:47][C][adc:026]:   Icon: 'mdi:flash'
[20:35:47][C][adc:029]:   Pin: VCC
[20:35:47][C][adc:051]:   Update Interval: 4294967.5s
[20:35:47][C][ota:029]: Over-The-Air Updates:
[20:35:47][C][ota:030]:   Address: 10.10.26.81:8266
[20:35:47][C][api:095]: API Server:
[20:35:47][C][api:096]:   Address: 10.10.26.81:6053
[20:35:47][C][mqtt:051]: MQTT:
[20:35:47][C][mqtt:053]:   Server Address: 10.10.26.67:1883 (10.10.26.67)
[20:35:47][C][mqtt:054]:   Username: 

[redacted]
[20:35:47][C][mqtt:055]:   Client ID: 

[redacted]
[20:35:47][C][mqtt:060]:   Topic Prefix: 'pir'
[20:35:47][C][mqtt:062]:   Log Topic: 'pir/debug'
[20:35:47][C][sb1:242]: SB1 UART:
[20:35:47][C][sb1:243]:   Boot Mode: NORMAL
[20:35:47][C][sb1:244]:   Product Info: {"p":"Okurono2XLVRV0fB","v":"1.0.2","m":0}
[20:35:47][C][wifi_signal.sensor:009]: WiFi Signal 'PIR WiFi Signal'
[20:35:47][C][wifi_signal.sensor:009]:   Unit of Measurement: 'dB'
[20:35:47][C][wifi_signal.sensor:009]:   Accuracy Decimals: 0
[20:35:47][C][wifi_signal.sensor:009]:   Icon: 'mdi:wifi'
[20:35:47][C][mqtt.sensor:024]: MQTT Sensor 'PIR WiFi Signal':
[20:35:47][C][mqtt.sensor:028]:   State Topic: 'pir/sensor/pir_wifi_signal/state'
[20:35:47][C][mqtt.sensor:024]: MQTT Sensor 'PIR Battery':
[20:35:47][C][mqtt.sensor:028]:   State Topic: 'pir/sensor/pir_battery/state'
[20:35:47][C][mqtt.binary_sensor:018]: MQTT Binary Sensor 'PIR Motion':
[20:35:47][C][mqtt.binary_sensor:019]:   State Topic: 'pir/binary_sensor/pir_motion/state'
[20:35:47][D][sb1:350]: Event message of length 5
[20:35:47][D][sb1:352]: 00: 0x66
[20:35:47][D][sb1:352]: 01: 0x04
[20:35:47][D][sb1:352]: 02: 0x00
[20:35:47][D][sb1:352]: 03: 0x01
[20:35:47][D][sb1:352]: 04: 0x00
[20:35:47][I][sb1:370]: Reset event: 0
[20:35:47][D][sb1:185]: state: 15 -> 13 after 432 ms
[20:35:47][I][sb1:343]: Rebooting: SB1_STATE_EVENT_ACK
[20:35:47][I][app:137]: Rebooting safely...
[20:35:47][D][sb1:392]: SB1 UART shutting down; next boot mode NORMAL

What would cause this device to keep getting the reset event?

pir.yaml is the same as the one provided in master. I have checked the other device I have which also runs into the same problem when flashed.

Device Link: https://www.aliexpress.com/item/32980093163.html?spm=a2g0s.9042311.0.0.27424c4ddgnzlP

p3p1 commented 4 years ago

+1 I have exactly the same issue

geerdkakes commented 4 years ago

Hi, I have the same issue. Any luck solving this?

ollieatkinson commented 4 years ago

@geerdkakes Sorry, I haven't investigated any further. When I get back around to this I am going to try flash with Tasmota

inorhan commented 3 years ago

Hi, Same issue here. Any luck solving this? Okurono2XLVRV0fB 1.0.2