search

gtxaspec / wz_mini_hacks

wz camera mods... make your camera better.
1.33k stars 114 forks source link

Wyze V4 HL_CAM4 #760

Closed gtxaspec closed 7 months ago

gtxaspec commented 7 months ago 
U-Boot SPL 2013.07
Board info: T41NQ

apll_freq = 1104000000 
mpll_freq = 1440000000 
vpll_freq = 1188000000 
sdram init start
DDR clk rate 720000000
DDRP_INNOPHY_PLL_CTRL: 00000028
DDRP_INNOPHY_PLL_CTRL: 00000020
T41NQ ddr phy skew set
mem data:
81000000:   00000000  ffffffff  00000000  ffffffff
81000010:   00000000  ffffffff  00000000  ffffffff
81000020:   00000000  ffffffff  00000000  ffffffff
81000030:   00000000  ffffffff  00000000  ffffffff
image entry point: 0x80100000
Board: ISVP (Ingenic XBurst2 T41 SoC)
DRAM size is 128 MiB
DTB: 0x8013aefc
Top of RAM usable for U-Boot at: 88000000
Reserving 427k for U-Boot at: 87f94000
Reserving 32772k for malloc() at: 85f93000
Reserving 32 Bytes for Board Info at: 85f92fe0
Reserving 124 Bytes for Global Data at: 85f92f64
Reserving 128k for boot params() at: 85f72f64
Stack Pointer at: 85f72f48
Now running in RAM - U-Boot at: 87f94000
MMC:   MSC: 0
Using default environment

Data transfer:    serial
gpio_request lable = wifi_enable_gpio gpio = 78
gpio_request lable = red_gpio gpio = 39
gpio_request lable = blue_gpio gpio = 38
gpio_request lable = white_light gpio = 48
gpio_request lable = white_light power en gpio = 47
gpio_request lable = 850_light_gpio gpio = 46
gpio_request lable = SPK_able_gpio gpio = 63
gpio_request lable = TF_SD_M_gpio gpio = 59
gpio_request lable = TF_sdcard_en_gpio gpio = 57
gpio_request lable = TF_CD_N_gpio gpio = 58
gpio_request lable = SD_power_en_gpio gpio = 61
gpio_request lable = wifi_enable_gpio gpio = 78
Hit any key to stop autoboot:  0 
gpio_request lable = sdupgrade gpio = 62
SF: Detected XT25F128B, flash size: 16MB, manufacturer id: 0b

SF: Detected XT25F128B, flash size: 16MB, manufacturer id: 0b

### JFFS2 loading 'upGradeFlag' to 0x85f72140
Scanning JFFS2 FS: . done.
find_inode failed for name=upGradeFlag
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for upGradeFlag!
gpio_request lable = TF_cd_gpio gpio = 58
SF: Detected XT25F128B, flash size: 16MB, manufacturer id: 0b

--->probe spend 6 ms
SF: 4653056 bytes @ 0x30000 Read: OK
--->read spend 1502 ms
## Loading kernel from FIT Image at 80600000 ...
   Using 'conf' configuration
   Verifying Hash Integrity ... sha256,rsa2048:kernel-dev+ sha256,rsa2048:kernel-dev+ OK
   Trying 'kernel' kernel subimage
     Description:  ingenict41 kernel
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x80604240
     Data Size:    1580704 Bytes = 1.5 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x80f00000
     Entry Point:  0x80f00000
     Hash algo:    sha256
   Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 80600000 ...
   Using 'conf' configuration
   Trying 'ramdisk' ramdisk subimage
     Description:  ingenict41 ramdisk
     Type:         RAMDisk Image
     Compression:  uncompressed
     Data Start:   0x807861ec
     Data Size:    2379776 Bytes = 2.3 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x00000000
     Entry Point:  0x38000000
     Hash algo:    sha256
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 80600000 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  ingenict41 dtb
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x806000c4
     Data Size:    16529 Bytes = 16.1 KiB
     Architecture: MIPS
     Hash algo:    sha256
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x806000c4 to 0x83000000
   Booting using the fdt blob at 0x83000000
   Loading Kernel Image ... OK
   Loading Ramdisk to 85d25000, end 85f6a000 ... OK
   Loading Device Tree to 85d1d000, end 85d24090 ... OK

Starting kernel ...

[    0.000000] Linux version 4.4.94
[    0.000000] CPU0 RESET ERROR PC:F6FE8FE2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00132100 (Ingenic XBurst@II)
[    0.000000] FPU revision is: 00f32100
[    0.000000] MIPS: machine is ingenic,marmot
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 00457000 @ 00010000 (usable)
[    0.000000]  memory: 00039000 @ 00467000 (usable after init)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 06400000 @ 00000000 (usable)
[    0.000000] Initial ramdisk at: 0x85d25000 (2379776 bytes)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x00000000063fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x00000000063fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000063fffff]
[    0.000000] [SMP] Slave CPU(s) 1 available.
[    0.000000] Primary instruction cache 32kB, VIPT, 8-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Unified secondary cache 128kB 8-way, linesize 64 bytes.
[    0.000000] PERCPU: Embedded 9 pages/cpu @81117000 s8176 r8192 d20496 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 25400
[    0.000000] Kernel command line: console=ttyS1,115200n8 mem=100M@0x0 rmem=20M@0x6400000 nmem=8M@0x7800000 init=/linuxrc ro root=/dev/ram0 rootfstype=squashfs init=/linuxrc mtdparts=sfc0_nor:192K(uboot),4544K(boot),5632K(system),5632K(back),320K(cfg),64K(provisioning) lpj=11968512
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 93948K/102400K available (3344K kernel code, 164K rwdata, 928K rodata, 228K init, 98K bss, 8452K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] parse cpu-intc-iomap, intc define in dt is too large!
[    0.000000] core irq setup finished and percpu irq inited! NR_IRQS = 419
[    0.000000] t41 Clock Power Management Unit init sucess!
[    0.000000] parse cpu-ost-iomap, ost number define in dt is too large!
[    0.000000] percpu cpu_num:0 timerevent init
[    0.000000] clockevents_config_and_register success.
[    0.000000] clocksource: jz_clocksource: mask: 0x7fffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000146] Calibrating delay loop (skipped) preset value.. 2393.70 BogoMIPS (lpj=11968512)
[    0.008558] pid_max: default: 32768 minimum: 301
[    0.013327] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.019983] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.027720] [SMP] Prepare 2 cores., cpu: 0
[    0.105969] [SMP] Booting CPU1 ...
[    0.109341] CPU1 RESET ERROR PC:FEFE77FA
[    0.109358] Primary instruction cache 32kB, VIPT, 8-way, linesize 32 bytes.
[    0.109363] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[    0.109368] Unified secondary cache 128kB 8-way, linesize 64 bytes.
[    0.109432] percpu cpu_num:1 timerevent init
[    0.109449] clockevents_config_and_register success.
[    0.109455] CPU1 revision is: 00132100 (Ingenic XBurst@II)
[    0.109458] FPU revision is: 00f32100
[    0.109669] Brought up 2 CPUs
[    0.156506] devtmpfs: initialized
[    0.161472] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.171428] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.177659] pinctrl core: initialized pinctrl subsystem
[    0.183225] NET: Registered protocol family 16
[    0.189222] ingenic pinctrl 10010000.pinctrl: 4 gpio chip add success, pins 128
[    0.197462] ingenic pinctrl 10010000.pinctrl: ingenic pinctrl probe success
[    0.206020] dmmu_init 807 PTRS_PER_PTE = 1024
[    0.218376] ingenic-dma 13420000.dma: INGENIC SoC DMA initialized
[    0.224735] usbcore: registered new interface driver usbfs
[    0.230298] usbcore: registered new interface driver hub
[    0.235713] usbcore: registered new device driver usb
[    0.240936] inno phy probe success
[    0.245680] clocksource: Switched to clocksource jz_clocksource
[    0.253086] NET: Registered protocol family 2
[    0.258015] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.265020] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.271519] TCP: Hash tables configured (established 1024 bind 1024)
[    0.277966] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.283828] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.290359] NET: Registered protocol family 1
[    0.294904] Trying to unpack rootfs image as initramfs...
[    0.300619] rootfs image is not initramfs (junk in compressed archive); looks like an initrd
[    0.314439] Freeing initrd memory: 2324K
[    0.319787] squashfs: version 4.0 (2021/14/49) Phillip Lougher 
[    0.325870] jffs2: version 2.2. © 2001-2006 Red Hat, Inc.
[    0.332483] io scheduler noop registered
[    0.336501] io scheduler cfq registered (default)
[    0.341376] ingenic,t41-pwm 13460000.pwm: PWM clk100k:480
[    0.346853] ingenic,t41-pwm 13460000.pwm: period_ns:max=1365312,min=42
[    0.354569] Ingenic drawbox probe sucess!
[    0.358869] vpu_register
[    0.361354] helix probe success
[    0.364833] dma_malloc of jzaip_t is ok! size = 1024 Bytes
[    0.370727] dma_malloc of jzaip_f is ok! size = 106600 Bytes
[    0.376817] dma_malloc of jzaip_p is ok! size = 221184 Bytes
[    0.382727] @@@ AIP driver init sucess (Version: H20230331a) @@@
[    0.389004] 10030000.serial: ttyS0 at MMIO 0x10030000 (irq = 59, base_baud = 7500000) is a uart0
[    0.398278] 10031000.serial: ttyS1 at MMIO 0x10031000 (irq = 58, base_baud = 7500000) is a uart1
[    0.407221] console [ttyS1] enabled
[    0.407221] console [ttyS1] enabled
[    0.414322] bootconsole [early0] disabled
[    0.414322] bootconsole [early0] disabled
[    0.423884] brd: module loaded
[    0.429104] ingenic-tcu 10002000.tcu: Ingenic TCU driver register completed ret = 0
[    0.437808] ingenic-sfc 13440000.sfc0: Found Supported nor device, BE = 32K, id = b4018, name = XT25F128B
[    0.447948] ingenic-sfc 13440000.sfc0: nor flash now use standard mode!
[    0.454902] 6 cmdlinepart partitions found on MTD device sfc0_nor
[    0.461324] Creating 6 MTD partitions on "sfc0_nor":
[    0.466548] 0x000000000000-0x000000030000 : "uboot"
[    0.472813] 0x000000030000-0x0000004a0000 : "boot"
[    0.478959] 0x0000004a0000-0x000000a20000 : "system"
[    0.485218] 0x000000a20000-0x000000fa0000 : "back"
[    0.491372] 0x000000fa0000-0x000000ff0000 : "cfg"
[    0.497442] 0x000000ff0000-0x000001000000 : "provisioning"
[    0.504275] ingenic-sfc 13440000.sfc0: SPI NOR MTD LOAD OK
[    0.510406] OTG CLK 1f9f2fc4
[    0.514700] CPCCR CLK 1580
[    0.717308] dwc2 13500000.otg: DWC OTG Controller
[    0.722284] dwc2 13500000.otg: new USB bus registered, assigned bus number 1
[    0.729759] dwc2 13500000.otg: irq 29, io mem 0x00000000
[    0.736176] hub 1-0:1.0: USB hub found
[    0.740151] hub 1-0:1.0: 1 port detected
[    0.744890] ingenic-i2c 10050000.i2c: register i2c0 success.
[    0.751807] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    0.760976] sdhci: Secure Digital Host Controller Interface driver
[    0.767519] sdhci: Copyright(c) Pierre Ossman
[    0.772483] ingenic,sdhci 13060000.msc: allocated mmc-pwrseq
[    0.815748] mmc0: SDHCI controller on ingenic-sdhci [13060000.msc] using ADMA
[    0.838995] mmc0: card removed
[    0.887944] mmc1: SDHCI controller on ingenic-sdhci [13070000.msc] using ADMA
[    0.902493] NET: Registered protocol family 17
[    0.908524] soc_vpu probe success,version:1.0.0-03203fd46d
[    0.928672] RAMDISK: squashfs filesystem found at block 0
[    0.934347] RAMDISK: Loading 2321KiB [1 disk] into ram disk... done.
[    1.017465] VFS: Mounted root (squashfs filesystem) readonly on device 1:0.
[    1.027898] mmc1: new high speed SDIO card at address 0001
[    1.028035] devtmpfs: mounted
[    1.028200] Freeing unused kernel memory: 228K
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
fs_mgr start...
[    1.427086] random: nonblocking pool is initialized
Verity success
Mount root success [mount -t squashfs -o ro /dev/dm-0 /system]
[    1.528867] @@@@ avpu driver ok(version H20220825a) @@@@@
[    1.636375] @@@@ tx-isp-probe ok (version H20231009a) compiler date: Oct 12 2023 @@@@
[    1.695736] @@@@@ inner codec power up@@@@@@
[    2.085749] @@@@ audio driver ok(version H20230311a) @@@@@
[    2.110285] exFAT: Version 1.2.9
[    2.123503] usbcore: registered new interface driver ch37x
[    2.131354] usbcore: registered new interface driver usb_ch341
[    2.137541] ch341: USB serial driver for ch340, ch341, etc.
[    2.143559] ch341: V1.6 On 2020.12.23
[    2.149321] loading jz-dtrng driver
[    2.153178] jz_dtrng_probe 281
[    2.156457] jz_dtrng_probe, dtrng iomem is :0xb0072000
[    2.161889] jz_dtrng_probe, dtrng irq is : 42
[    2.166773] jz_dtrng_probe: probe() done
[    2.185176] @@@@ soc nna probe sucess (Board: T41, Version: H20230310) @@@
[    2.192572] soc_nna_init success
[    2.391924] [atbm_log]:platform_init(252)
[    2.396262] [atbm_log]:SVN_VER=3047,DPLL_CLOCK=40,BUILD_TIME=[===== =====]
[    2.403472] [atbm_log]:----drvier support chip Cronus 
[    2.409541] [atbm_log]:Probe called
[    2.413286] [atbm_log]:atbm_sdio_probe:v12
[    2.417679] [atbm_log]:Allocated hw_priv @ 829e9240
[    2.423220] [atbm_log]: wait_event_interruptible from  send_prbresp_wq
[    2.423249] [atbm_log]:[BH] register.
[    2.434333] [atbm_log]:atbmwifi INIT_WORK enable
[    2.439665] [atbm_log]:atbmwifi INIT_WORK enable
[    2.446012] [atbm_log]:atbm_get_chiptype, chipver=0x5a, g_wifi_chip_type[12]
[    2.453410] [atbm_log]:atbm_before_load_firmware++
[    2.459136] [atbm_log]:atbm_before_load_firmware:do not set config to smu
[    2.488817] [atbm_log]:atbm_before_load_firmware:0xab0016c = [34800000]
[    2.496028] [atbm_log]:atbm_before_load_firmware:0xab0016c = [34800000]
[    2.503394] [atbm_log]:reset val(2)
[    2.507729] [atbm_log]:after reset(0)
[    2.511574] [atbm_log]:atbm_start_load_firmware++
[    2.516792] fwhdr->flags 34353678 sram_addr 9023000
[    2.521914] [atbm_log]:
[    2.521914] ======>>> load WIFI BLE COMB firmware <<<======
[    2.521914] 
[    2.532307] [atbm_log]:START DOWNLOAD ICCM=========
[    2.537470] [atbm_log]:atbm_load_firmware_generic: addr 60000: len 20000
[    2.622841] [atbm_log]:START DOWNLOAD DCCM=========
[    2.628004] [atbm_log]:atbm_load_firmware_generic: addr 800000: len d000
[    2.664622] [atbm_log]:START DOWNLOAD BLE SRAM=========
[    2.670154] [atbm_log]:atbm_load_firmware_generic: addr 9023000: len 10000
[    2.713589] [atbm_log]:atbm_after_load_firmware++
[    2.755758] [atbm_log]:ATBM_HIFREG_CONFIG_REG_ID(4005600)
[    2.765455] [atbm_log]:firmwareCap f189
[    2.769527] [atbm_log]:firmwareCap2 1a04
[    2.773639] [atbm_log]:wsm_caps.firmwareCap 1a04f189 16
[    2.778961] [atbm_log]:apollo wifi WSM init done.
[    2.778961]    Input buffers: 41 x 1632 bytes
[    2.778961]    Hardware: 7.21
[    2.778961]    WSM firmware [=MODEM=DPLL24M+BLE+plat=10 ApSleep 2GHZ]  expection 900c094, ep0 cmd addr 901c660 NumOfStations[0x10] NumOfInterfaces[3]
[    2.813796] [atbm_log]:EFUSE(8)              [0]
[    2.817741] [atbm_log]:EFUSE(I)                  [0]
[    2.821760] [atbm_log]:EFUSE(B)          [0]
[    2.825594] [atbm_log]:CAPABILITIES_ATBM_PRIVATE_IE      [0]
[    2.831544] [atbm_log]:CAPABILITIES_NVR_IPC              [0]
[    2.837490] [atbm_log]:CAPABILITIES_NO_CONFIRM           [1]
[    2.843421] [atbm_log]:CAPABILITIES_WOW                  [0]
[    2.849365] [atbm_log]:CAPABILITIES_NO_BACKOFF           [0]
[    2.855296] [atbm_log]:CAPABILITIES_CFO                  [0]
[    2.861245] [atbm_log]:CAPABILITIES_CHIP_FLAG            [1]
[    2.867190] [atbm_log]:CAPABILITIES_TXCAL                [1]
[    2.873121] [atbm_log]:CAPABILITIES_LMAC_BAB_SETUP       [0]
[    2.879064] [atbm_log]:CAPABILITIES_FORCE_PM_ACTIVE      [0]
[    2.884995] [atbm_log]:CAPABILITIES_SMARTCONFIG          [0]
[    2.890948] [atbm_log]:CAPABILITIES_ETF                  [1]
[    2.896893] [atbm_log]:CAPABILITIES_BLE                  [1]
[    2.901822] [atbm_log]:CAPABILITIES_40M                  [1]
[    2.906764] [atbm_log]:CAPABILITIES_LDPC                 [1]
[    2.911784] [atbm_log]:CAPABILITIES_NAV_ENABLE              [0]
[    2.918001] [atbm_log]:CAPABILITIES_USB_RECOVERY_BUG     [0]
[    2.923932] [atbm_log]:CAPABILITIES_USE_IPC              [0]
[    2.929875] [atbm_log]:CAPABILITIES_OUTER_PA             [0]
[    2.935819] [atbm_log]:CAPABILITIES_WFA    [0]
[    2.940475] [atbm_log]:CAPABILITIES_EAP_GROUP_REKEY  [0]
[    2.946055] [atbm_log]:CAPABILITIES_RTS_LONG_DURATION    [0]
[    2.951986] [atbm_log]:CAPABILITIES_TX_CFO_PPM_CORRECTION[0]
[    2.957929] [atbm_log]:CAPABILITIES_RXCAL       [1]
[    2.963040] [atbm_log]:CAPABILITIES_HW_CHECKSUM          [0]
[    2.968984] [atbm_log]:CAPABILITIES_80211_TO_8023 [1]
[    2.974277] [atbm_log]:CAPABILITIES_NEW_CHIPER  [1]
[    2.979401] [atbm_log]:CONFIG_PRODUCT_TEST_USE_FEATURE_ID [1]
[    2.985422] [atbm_log]:CONFIG_PRODUCT_TEST_USE_GOLDEN_LED [1]
[    2.991672] [atbm_log]:atbm_sdio_rx_thread
[    3.013524] [atbm_log]:set_block_size=256
[    3.017779] [atbm_log]:mdelay wait wsm_startup_done  !!
[    3.024398] [atbm_log]:atbm_sdio_sg_thread
[    3.029902] [atbm_log]:atbm_sdio_tx_thread
[    3.029943] [atbm_log]:wsm_generic_confirm:status(2)
[    3.039592] [atbm_log]:<WARNING> wsm_write_mib fail !!! mibId=4132
[    3.047039] [atbm_log]:apollo wifi : can't open /data/.mac.info
[    3.064092] [atbm_log]:apollo wifi : can't open /tmp/atbm_txpwer_dcxo_cfg.txt
[    3.071668] [atbm_log]:win txpower:0
[    3.075233] [atbm_log]:use default power
[    3.085728] [atbm_log]:rx timeout
[    3.111958] [atbm_log]:0,target_or_delta=1
[    3.116371] [atbm_log]:1,b_1M_2M=185
[    3.120146] [atbm_log]:2,b_5_5M_11M=185
[    3.124165] [atbm_log]:3,g_6M_n_6_5M=170
[    3.128833] [atbm_log]:4,g_9M=170
[    3.132313] [atbm_log]:5,g_12M_n_13M=165
[    3.136850] [atbm_log]:6,g_18M_n_19_5M=165
[    3.141148] [atbm_log]:7,g_24M_n_26M=165
[    3.145257] [atbm_log]:8,g_36M_n_39M=165
[    3.149499] [atbm_log]:9,g_48M_n_52M=165
[    3.153821] [atbm_log]:10,g_54M_n_58_5M=165
[    3.158250] [atbm_log]:11,n_65M=155
[    3.162047] [atbm_log]:12,HE-SU_MCS0=170
[    3.166213] [atbm_log]:13,HE-SU_MCS1=170
[    3.170454] [atbm_log]:14,HE-SU_MCS2=160
[    3.174569] [atbm_log]:15,HE-SU_MCS3=160
[    3.178789] [atbm_log]:16,HE-SU_MCS4=150
[    3.183100] [atbm_log]:17,HE-SU_MCS5=150
[    3.187267] [atbm_log]:18,HE-SU_MCS6=150
[    3.191510] [atbm_log]:19,HE-SU_MCS7=140
[    3.195624] [atbm_log]:20,HE-SU_MCS8=140
[    3.199783] [atbm_log]:21,HE-SU_MCS9=140
[    3.204049] [atbm_log]:22,HE-SU_MCS10=140
[    3.208370] [atbm_log]:23,HE-SU_MCS11=130
[    3.212742] [atbm_log]:24,g_6M_n_6_5M_40M=170
[    3.217375] [atbm_log]:25,g_9M_40M=170
[    3.221435] [atbm_log]:26,g_12M_n_13M_40M=165
[    3.226050] [atbm_log]:27,g_18M_n_19_5M_40M=165
[    3.230929] [atbm_log]:28,g_24M_n_26M_40M=165
[    3.235500] [atbm_log]:29,g_36M_n_39M_40M=165
[    3.240163] [atbm_log]:30,g_48M_n_52M_40M=165
[    3.244925] [atbm_log]:31,g_54M_n_58_5M_40M=165
[    3.249723] [atbm_log]:32,n_65M_40M=155
[    3.253876] [atbm_log]:33,HE-SU_MCS0_40M=170
[    3.258406] [atbm_log]:34,HE-SU_MCS1_40M=170
[    3.263014] [atbm_log]:35,HE-SU_MCS2_40M=160
[    3.267606] [atbm_log]:36,HE-SU_MCS3_40M=160
[    3.272248] [atbm_log]:37,HE-SU_MCS4_40M=150
[    3.276780] [atbm_log]:38,HE-SU_MCS5_40M=150
[    3.281392] [atbm_log]:39,HE-SU_MCS6_40M=150
[    3.285919] [atbm_log]:40,HE-SU_MCS7_40M=140
[    3.290524] [atbm_log]:41,HE-SU_MCS8_40M=140
[    3.295005] [atbm_log]:42,HE-SU_MCS9_40M=140
[    3.299585] [atbm_log]:43,HE-SU_MCS10_40M=140
[    3.304341] [atbm_log]:44,HE-SU_MCS11_40M=130
[    3.308962] [atbm_log]:==read success==
[    3.313111] [atbm_log]:set absolute power
[    3.336632] [atbm_log]:get chip id [0][0][0] 
[    3.341206] [atbm_log]:current chiptype ATBM6062-S40 
[    3.347018] [atbm_log]:enable sg
[    3.350425] [atbm_log]:[wlan0] has been disabled
[    3.356371] [atbm_log]:enable sg
[    3.359787] [atbm_log]:[p2p0] has been disabled
[    3.365225] [atbm_log]:ble start
[    3.369140] [atbm_log]:[ALTOBEAM-ble_recv] start
[    3.374051] [atbm_log]:ble subscribe
[    3.374062] [atbm_log]:[ALTOBEAM-ble_xmit] start
[    3.383028] [atbm_log]:ble_platform_probe(828c3880)
[    3.388310] [atbm_log]:is registered as 'ALTOBEAM'
[    3.393488] [atbm_log]:default country code:00,support channel=14
[    3.400009] [atbm_log]:[atbm_wtd]:set wtd_probe = 1
net.core.wmem_max = 26214400
net.core.wmem_default = 26214400
#######################
#   IS USER STATUS   #
#######################
kernel.core_pattern = |/system/bin/ucoredmp_collector.sh --pid %p --signal %s --name %e --time %t --output-dir /media/mmc/cores
kernel.core_pipe_limit = 1
net.unix.max_dgram_qlen = 128

Welcome
t41 login:
gtxaspec commented 7 months ago

secure-boot enabled, verified. investigating further.

digitydogs commented 7 months ago

May be of some use in getting past the secure boot.. There are a few gits dedicated to ingenic booting ;)

https://github.com/OpenIPC/u-boot-ingenic/blob/master/README