Конфиг файл для Home Assistant для Neptun Smart системы защиты от протечек
- работает по Modbus TCP c WiFi, Ethernet или Tuya модулями.
- изменяем host в modbus на IP адресс своего Нептуна.
- добавлено 5 беспроводных датчиков, если нужно больше или меньше изменяем по примеру.
- заблокировал своему Neptun Smart полностью доступ в интернет на роутере. нет теперь никакого смысла в этом.
- сделано на основе Карта памяти регистров модуля управления Neptun Smart для протокола MODBUS-RTU
- также основано на конфигах(config-wb-neptun.json) для WirenBoard от Ермухамедов Максим (MaxE). Статья на sprut.ai
modbus:
- name: neptun_smart
type: tcp
host: 192.168.1.198
port: 503
delay: 3
timeout: 3
sensors:
- name: "Neptun Alarm and Mode Raw"
address: 0
slave: 240
input_type: holding
data_type: uint16
scan_interval: 10
- name: "Leak Sensor Raw"
address: 3
slave: 240
input_type: holding
data_type: uint16
scan_interval: 10
- name: "Number of Connected Wireless Sensors"
address: 6
slave: 240
input_type: holding
data_type: uint16
unit_of_measurement: "шт."
unique_id: "number_of_connected_wireless_sensors"
scan_interval: 30
- name: "Wireless Sensor 1 Raw"
address: 57
slave: 240
input_type: holding
data_type: uint16
scan_interval: 10
- name: "Wireless Sensor 2 Raw"
address: 58
slave: 240
input_type: holding
data_type: uint16
scan_interval: 10
- name: "Wireless Sensor 3 Raw"
address: 59
slave: 240
input_type: holding
data_type: uint16
scan_interval: 10
- name: "Wireless Sensor 4 Raw"
address: 60
slave: 240
input_type: holding
data_type: uint16
scan_interval: 10
- name: "Wireless Sensor 5 Raw"
address: 61
slave: 240
input_type: holding
data_type: uint16
scan_interval: 10
# Template sensor для двоичного представления значения
template:
sensor:
- name: "Neptun Alarm and Mode Binary"
state: "{{ '{:016b}'.format(states('sensor.neptun_alarm_and_mode_raw') | int) }}" # Двоичное представление 16 бит
### Wireless sensors ####
- name: "Battery Level Sensor 1"
unit_of_measurement: "%"
state: "{{ ((states('sensor.wireless_sensor_1_raw') | int) // (2 ** 8)) % 256 }}" # Извлечение битов 8–15
icon: mdi:battery
- name: "Sensor Signal Level 1"
unit_of_measurement: "%"
state: "{{ (((states('sensor.wireless_sensor_1_raw') | int) // (2 ** 3)) % 8) * 25 }}" # Извлечение битов 3–5 и умножение на 25 для масштабирования
icon: mdi:signal
- name: "Battery Level Sensor 2"
unit_of_measurement: "%"
state: "{{ ((states('sensor.wireless_sensor_2_raw') | int) // (2 ** 8)) % 256 }}"
icon: mdi:battery
- name: "Sensor Signal Level 2"
unit_of_measurement: "%"
state: "{{ (((states('sensor.wireless_sensor_2_raw') | int) // (2 ** 3)) % 8) * 25 }}"
icon: mdi:signal
# Новые сенсоры для Sensor 3
- name: "Battery Level Sensor 3"
unit_of_measurement: "%"
state: "{{ ((states('sensor.wireless_sensor_3_raw') | int) // (2 ** 8)) % 256 }}"
icon: mdi:battery
- name: "Sensor Signal Level 3"
unit_of_measurement: "%"
state: "{{ (((states('sensor.wireless_sensor_3_raw') | int) // (2 ** 3)) % 8) * 25 }}"
icon: mdi:signal
# Новые сенсоры для Sensor 4
- name: "Battery Level Sensor 4"
unit_of_measurement: "%"
state: "{{ ((states('sensor.wireless_sensor_4_raw') | int) // (2 ** 8)) % 256 }}"
icon: mdi:battery
- name: "Sensor Signal Level 4"
unit_of_measurement: "%"
state: "{{ (((states('sensor.wireless_sensor_4_raw') | int) // (2 ** 3)) % 8) * 25 }}"
icon: mdi:signal
# Новые сенсоры для Sensor 5
- name: "Battery Level Sensor 5"
unit_of_measurement: "%"
state: "{{ ((states('sensor.wireless_sensor_5_raw') | int) // (2 ** 8)) % 256 }}"
icon: mdi:battery
- name: "Sensor Signal Level 5"
unit_of_measurement: "%"
state: "{{ (((states('sensor.wireless_sensor_5_raw') | int) // (2 ** 3)) % 8) * 25 }}"
icon: mdi:signal
### END Wireless sensors ####
# Template binary sensors для отдельных битов
binary_sensor:
- name: "Floor Washing Mode"
state: "{{ states('sensor.neptun_alarm_and_mode_binary')[15] == '1' }}" # 0-й бит
- name: "Alarm zona 1"
state: "{{ states('sensor.neptun_alarm_and_mode_binary')[14] == '1' }}" # 1-й бит
- name: "Alarm zona 2"
state: "{{ states('sensor.neptun_alarm_and_mode_binary')[13] == '1' }}" # 2-й бит
- name: "LeakSensor 1"
state: "{{ states('sensor.leak_sensor_raw') | int | bitwise_and(1) > 0 }}" # 0-й бит регистра 3
- name: "Zona 1"
state: "{{ states('sensor.neptun_alarm_and_mode_binary')[7] == '1' }}" # 8-й бит
- name: "Zona 2"
state: "{{ states('sensor.neptun_alarm_and_mode_binary')[6] == '1' }}" # 9-й бит
- name: "Keypad Locks"
state: "{{ states('sensor.neptun_alarm_and_mode_binary')[3] == '1' }}" # 12-й бит
### Wireless sensors ####
- name: "Presence of Alarm Sensor 1"
state: "{{ (states('sensor.wireless_sensor_1_raw') | int) % 2 == 1 }}" # Проверка 0-го бита
icon: mdi:alarm
- name: "Availability of Category Sensor 1"
state: "{{ ((states('sensor.wireless_sensor_1_raw') | int) // (2 ** 1)) % 2 == 1 }}"
icon: mdi:check-circle
- name: "Sensor Loss Sensor 1"
state: "{{ ((states('sensor.wireless_sensor_1_raw') | int) // (2 ** 2)) % 2 == 1 }}"
icon: mdi:alert-circle
- name: "Presence of Alarm Sensor 2"
state: "{{ (states('sensor.wireless_sensor_2_raw') | int) % 2 == 1 }}"
icon: mdi:alarm
- name: "Availability of Category Sensor 2"
state: "{{ ((states('sensor.wireless_sensor_2_raw') | int) // (2 ** 1)) % 2 == 1 }}"
icon: mdi:check-circle
- name: "Sensor Loss Sensor 2"
state: "{{ ((states('sensor.wireless_sensor_2_raw') | int) // (2 ** 2)) % 2 == 1 }}"
icon: mdi:alert-circle
- name: "Presence of Alarm Sensor 3"
state: "{{ (states('sensor.wireless_sensor_3_raw') | int) % 2 == 1 }}"
icon: mdi:alarm
- name: "Availability of Category Sensor 3"
state: "{{ ((states('sensor.wireless_sensor_3_raw') | int) // (2 ** 1)) % 2 == 1 }}"
icon: mdi:check-circle
- name: "Sensor Loss Sensor 3"
state: "{{ ((states('sensor.wireless_sensor_3_raw') | int) // (2 ** 2)) % 2 == 1 }}"
icon: mdi:alert-circle
- name: "Presence of Alarm Sensor 4"
state: "{{ (states('sensor.wireless_sensor_4_raw') | int) % 2 == 1 }}"
icon: mdi:alarm
- name: "Availability of Category Sensor 4"
state: "{{ ((states('sensor.wireless_sensor_4_raw') | int) // (2 ** 1)) % 2 == 1 }}"
icon: mdi:check-circle
- name: "Sensor Loss Sensor 4"
state: "{{ ((states('sensor.wireless_sensor_4_raw') | int) // (2 ** 2)) % 2 == 1 }}"
icon: mdi:alert-circle
- name: "Presence of Alarm Sensor 5"
state: "{{ (states('sensor.wireless_sensor_5_raw') | int) % 2 == 1 }}"
icon: mdi:alarm
- name: "Availability of Category Sensor 5"
state: "{{ ((states('sensor.wireless_sensor_5_raw') | int) // (2 ** 1)) % 2 == 1 }}"
icon: mdi:check-circle
- name: "Sensor Loss Sensor 5"
state: "{{ ((states('sensor.wireless_sensor_5_raw') | int) // (2 ** 2)) % 2 == 1 }}"
icon: mdi:alert-circle
### END Wireless sensors ####
# Template binary_sensor для Dual Zone Mode
binary_sensor:
- platform: template
sensors:
dual_zone_mode:
friendly_name: "Dual Zone Mode"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(1024) > 0 }}" # 10-й бит
battery_drain_wireless_sensors:
friendly_name: "Battery Drain in Wireless Sensors"
unique_id: "battery_drain_wireless_sensors"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(8) > 0 }}" # Проверка 3-го бита
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(8) > 0 %}
mdi:battery-alert
{% else %}
mdi:battery
{% endif %}
lost_connection_wireless_sensors:
friendly_name: "Lost Connection with Wireless Sensors"
unique_id: "lost_connection_wireless_sensors"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(16) > 0 }}" # Проверка 4-го бита
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(16) > 0 %}
mdi:signal-off
{% else %}
mdi:signal
{% endif %}
# Template switches для управления Zona 1, Zona 2, и Zona 1 + Zona 2 с доступностью для Zona 2
switch:
- platform: template
switches:
zona_1_switch:
friendly_name: "Zona 1 Switch"
unique_id: "zona_1_switch"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(256) > 0 }}"
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(256) > 0 %}
mdi:water-pump
{% else %}
mdi:water-pump-off
{% endif %}
turn_on:
service: modbus.write_register
data_template:
hub: neptun_smart
unit: 240
address: 0
value: >
{% if is_state('binary_sensor.dual_zone_mode', 'off') %}
{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(768) }}
{% else %}
{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(256) }}
{% endif %}
turn_off:
service: modbus.write_register
data_template:
hub: neptun_smart
unit: 240
address: 0
value: >
{% if is_state('binary_sensor.dual_zone_mode', 'off') %}
{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(768)) }}
{% else %}
{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(256)) }}
{% endif %}
zona_2_switch:
friendly_name: "Zona 2 Switch"
unique_id: "zona_2_switch"
availability_template: "{{ is_state('binary_sensor.dual_zone_mode', 'on') }}" # Доступен только если Dual Zone Mode включён
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(512) > 0 }}"
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(256) > 0 %}
mdi:water-pump
{% else %}
mdi:water-pump-off
{% endif %}
turn_on:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(512) }}"
turn_off:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(512)) }}"
zona_1_2_switch:
friendly_name: "Zona 1 + Zona 2 Switch"
value_template: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(256)) > 0 and (states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(512)) > 0 }}"
turn_on:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(768) }}" # Устанавливаем 256 и 512 одновременно
turn_off:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(768)) }}" # Обнуляем 256 и 512
dual_zone_mode_switch:
friendly_name: "Dual Zone Mode Switch"
unique_id: "dual_zone_mode_switch"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(1024) > 0 }}" # Проверка 10-го бита
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(1024) > 0 %}
mdi:tally-mark-2
{% else %}
mdi:tally-mark-1
{% endif %}
turn_on:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(1024) }}" # Устанавливаем 10-й бит
turn_off:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(1024)) }}" # Обнуляем 10-й бит
floor_washing_mode_switch:
friendly_name: "Floor Washing Mode Switch"
unique_id: "floor_washing_mode_switch"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(1) > 0 }}" # Проверка 0-го бита
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(1) > 0 %}
mdi:shower
{% else %}
mdi:shower-head
{% endif %}
turn_on:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(1) }}" # Устанавливаем 0-й бит
turn_off:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(1)) }}" # Обнуляем 0-й бит
keypad_locks_switch:
friendly_name: "Keypad Locks Switch"
unique_id: "keypad_locks_switch"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(4096) > 0 }}" # Проверка 12-го бита
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(4096) > 0 %}
mdi:keyboard-off
{% else %}
mdi:keyboard
{% endif %}
turn_on:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(4096) }}" # Устанавливаем 12-й бит
turn_off:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(4096)) }}" # Обнуляем 12-й бит
closing_taps_on_sensor_lost:
friendly_name: "Closing Taps on Sensor Lost"
unique_id: "closing_taps_on_sensor_lost_switch"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(2048) > 0 }}" # Проверка 11-го бита
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(2048) > 0 %}
mdi:water-off
{% else %}
mdi:water
{% endif %}
turn_on:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(2048) }}" # Устанавливаем 11-й бит
turn_off:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(2048)) }}" # Обнуляем 11-й бит
procedure_for_connecting_wireless_devices:
friendly_name: "Procedure for Connecting Wireless Devices"
unique_id: "procedure_for_connecting_wireless_devices_switch"
value_template: "{{ states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(128) > 0 }}" # Проверка 7-го бита
icon_template: >
{% if states('sensor.neptun_alarm_and_mode_raw') | int | bitwise_and(128) > 0 %}
mdi:wifi
{% else %}
mdi:wifi-off
{% endif %}
turn_on:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_or(128) }}" # Устанавливаем 7-й бит
turn_off:
service: modbus.write_register
data:
hub: neptun_smart
unit: 240
address: 0
value: "{{ (states('sensor.neptun_alarm_and_mode_raw') | int) - ((states('sensor.neptun_alarm_and_mode_raw') | int) | bitwise_and(128)) }}" # Обнуляем 7-й бит
В основном конфиге только 1 проводная линия. Если нужно добавить дополнительные проводные линии, берем отсюда и вставляем там где LeakSensor 1:
- name: "LeakSensor 1"
state: "{{ states('sensor.leak_sensor_raw') | int | bitwise_and(1) > 0 }}" # Бит 0 регистра 3
- name: "LeakSensor 2"
state: "{{ states('sensor.leak_sensor_raw') | int | bitwise_and(2) > 0 }}" # Бит 1 регистра 3
- name: "LeakSensor 3"
state: "{{ states('sensor.leak_sensor_raw') | int | bitwise_and(4) > 0 }}" # Бит 2 регистра 3
- name: "LeakSensor 4"
state: "{{ states('sensor.leak_sensor_raw') | int | bitwise_and(8) > 0 }}" # Бит 3 регистра 3