Camera won't initialise

[alport]

Using Thonny, I've successfully installed your latest binary: https://github.com/lemariva/micropython-camera-driver/blob/master/firmware/micropython_camera_feeeb5ea3_esp32_idf4_4.bin and get the Micropython prompt,

but, I can't seem to get past the simplest test:

import camera camera.init(0, format=camera.JPEG, fb_location=camera.PSRAM) Traceback (most recent call last): File "", line 1, in OSError: Camera Init Failed

Any pointers please? Thanks,

[lemariva]

Hey! can you please flash the firmware using esptool and connect to the board using VSCode and the PyMakr plugin? The firmware seems to be working by other users e.g. https://github.com/lemariva/micropython-camera-driver/issues/36#issuecomment-1029051970 . Thus, I think the IDE is the problem. You can follow the steps here: https://lemariva.com/blog/2022/01/micropython-upgraded-support-cameras-m5camera-esp32-cam-etc

[aguaviva]

Same issue here with the AIThinker esp32-cam

import camera camera.init(0, format=camera.JPEG, fb_location=camera.PSRAM) Traceback (most recent call last): File "", line 6, in OSError: Camera Init Failed

I flashed your firmware this way:

esptool.py --port /dev/ttyUSB0 erase_flash esptool.py --chip esp32 --port /dev/ttyUSB0 write_flash -z 0x1000 ~/Downloads/micropython_camera_feeeb5ea3_esp32_idf4_4.bin

[Yimro]

Hello, I know this is an old thread, but I have the same problem. After flashing the firmware everything is fine. After a few times initializing and deinitializing, I get error messages.

I have a cheapo-version AI-Thinker ESP32-CAM and installed the @lemariva firmware like this:

esptool.py --port /dev/ttyUSB0 erase_flash
esptool.py --chip esp32 --port /dev/ttyUSB0 write_flash -z 0x1000 micropython_camera_feeeb5ea3_esp32_idf4_4.bin 

When trying to initialize the camera in Thonny, I run:

import camera
camera.init(0, format=camera.JPEG, fb_location=camera.PSRAM)

which is fine for a couple of times, then results results in an error:

Traceback (most recent call last):
  File "<stdin>", line 2, in <module>
OSError: Camera Init Failed

When running in a terminal, the error description has more useful details:

MicroPython v1.18-74-gfeeeb5ea3 on 2022-02-02; ESP32-cam module (i2s) with ESP32
Type "help()" for more information.
>>> import camera
>>> camera.init(0, format=camera.JPEG, fb_location=camera.PSRAM)
E (17020) gpio: gpio_install_isr_service(449): GPIO isr service already installed
E (17020) camera: Camera probe failed with error 0x103(ESP_ERR_INVALID_STATE)
E (17030) camera: Camera Init Failed
Traceback (most recent call last):
  File "<stdin>", line 1, in <module>
OSError: Camera Init Failed

Sometimes on trying to camera.init(0, format=camera.JPEG, fb_location=camera.PSRAM), the error messages in the terminal look like this:

E (170) sccb: SCCB_Write Failed addr:0x30, reg:0xff, data:0x01, ret:-1
E (170) camera: Detected camera not supported.
E (170) camera: Camera probe failed with error 0x106(ESP_ERR_NOT_SUPPORTED)

and like this:

E (13290) camera: Camera probe failed with error 0x105(ESP_ERR_NOT_FOUND)

So, different errors. I found out that disconnecting and connecting the ESP32-CAM physically or pressing the "reset" button sometimes resolves this issue in many cases.

[SaitamaTechno]

Hello, if anyone still faces the issue, here is a solution: You need to deinit the camera at the end of ever camera usage. Here is a sample code: ` def take_photo(qualityy): camera.quality(qualityy) #between 10-63 lower number means higher quality buf = camera.capture() return buf

def camera_deinit(): camera.deinit()

`