search

openfab-lab / toolsDocs

Repo pour la documentation des machines
3 stars 5 forks source link

laser module TTL vs PWM #13

Open nicolasdb opened 5 years ago

nicolasdb commented 5 years ago

Ok, Houston, we have a problem.

I order a second minilaser diode for fabmob but I was not please with the first one and I order the same used by bemaker this time. The machine is arrived, it's mounted but the laser module is lost somewhere. Hopefully, I bought earlier another laser module as safety parts. and because it's never easy and never work on the first attempt, connectors don't fit.

It's same same as the first (I was thinking) image

But with Eleksmaker, it's a 3pin cable for the same module but like this. image

The control board is the "SW-LD62 v2" And I found this part. image

Description: This PWM TO TTL laser module is design for EleksMaker series machine and its controller board. But it can also be used for other DIY machine which need to change TTL modulation.

Specification: Power port size: 5.5*2.1mm Working voltage: DC 12V Woring power: >2A

Eleksmaker use the mana board controler. image

The other is laseraxes board. image Seems less good than the other. And the power supply connector is a bit loose, it doesn't match the size of the power supply (2.5mm vs 2.1mm probably, tssss) But have 2 place to connect laser, depending of the laser power. both 2pins. note: I have a second mana board... ^^

So my question is simply, "what about unsolder 2pin connector and solder 3pin connect instead?" Right?

nicolasdb commented 5 years ago

last thing is the first laser module doesn't have the board, it's directly connected to the controler board laseraxe. https://www.aliexpress.com/store/product/ZONESUN-Engraving-Machine-Laser-axe-405nm-2500mW-DIY-Desktop-Mini-Laser-Engraver-Laser-Cutter-Etcher-17X20cm/4425009_32894209182.html

nicolasdb commented 5 years ago

Here's the response from AliExpress shop gktools. Yeaaaaah China!

Hi， Nicolas, We are very sorry for the delivery delay, I will call the express company, then I will reply you. The 2p2p laser can used for the control board, if you can change the pin connector. Sincerely! Jamie.

nicolasdb commented 5 years ago

Connector changed from 2p2p to 3p. C image

Careful to the poles...

I didn't had special connetors. ^^ Red wire on VCC

image

image

image

Match poles from controller. 12V/GND/PWM image

image

nicolasdb commented 5 years ago

Still a problem with eleksmaker and chinese Arduino + laserweb. => BSOD with windows 7,8,10. Bug with ch340 USB chipset.... Working fine with linux.

What is this ArduinoClone? usb chip CH340x Original is usb chip FTDI https://www.exp-tech.de/plattformen/arduino/4450/arduino-nano

Bon, Bsod, j'ai perdu ma doc sur le fabmob10.

https://www.pihomeserver.fr/en/2018/02/17/raspberry-pi-gravage-laser-cnc-eleksmaker-a3-pro/

nicolasdb commented 5 years ago

rapidement https://www.youtube.com/watch?v=oXHmOdObTvw

check EEprom setings via "$$"

"120","X-axis acceleration","mm/sec^2","X-axis acceleration. Used for motion planning to not exceed motor torque and lose steps." "121","Y-axis acceleration","mm/sec^2","Y-axis acceleration. Used for motion planning to not exceed motor torque and lose steps." "122","Z-axis acceleration","mm/sec^2","Z-axis acceleration. Used for motion planning to not exceed motor torque and lose steps."

"100","X-axis travel resolution","step/mm","X-axis travel resolution in steps per millimeter." "101","Y-axis travel resolution","step/mm","Y-axis travel resolution in steps per millimeter." "102","Z-axis travel resolution","step/mm","Z-axis travel resolution in steps per millimeter."

actual X: 10mm = 31mm step = 250

$100, $101 and $102 – [X,Y,Z] steps/mm
Grbl needs to know how far each step will take the tool in reality. To calculate steps/mm for an axis of your machine you need to know:
    The mm traveled per revolution of your stepper motor. This is dependent on your belt drive gears or lead screw pitch.
    The full steps per revolution of your steppers (typically 200)
    The microsteps per step of your controller (typically 1, 2, 4, 8, or 16). Tip: Using high microstep values (e.g., 16) can reduce your stepper motor torque, so use the lowest that gives you the desired axis resolution and comfortable running properties.
The steps/mm can then be calculated like this: steps_per_mm = (steps_per_revolution*microsteps)/mm_per_rev

Compute this value for every axis and write these settings to Grbl.
nicolasdb commented 5 years ago

image

https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration#quick-guide-to-setting-up-your-machine-for-the-first-time

nicolasdb commented 5 years ago

note concernant elekslaser little sebastian

16 Octobre

image

image

image

En soit, l'écart n'est pas si grave et j'ai même agrandit. Pour éviter les tensions dans les matériaux. Lorsque j'ai déserré les vis, Les profils s'écartent, tout seul à cause du bras X qui exerce une pression des roues vers l'extérieur . Bref, ne pas forcer. Mais bien serrer et que tout soit bien d'équerre.

LA coupe du profilé alu était le coupable. Lorsqu'on serre, le plexi se plaque contre la coupe et se déforme un peu. Ce qui crée tension et désalignement. J'ai ajouté une carte de visite à gauche et ça a rectifié le décalage. YEah.

image

image image image

ça devrait être bien là. Vive la colle chaude.

Done

image

image

Ressource tuto assemblage. pour le futur. https://www.instructables.com/id/How-To-Laser-Cutter/

Et planche de travail pour en dessous.

image https://www.thingiverse.com/thing:1678366

côté logiciel,

screenshot from 2018-10-16 16-26-25 Voir calculateur prusa.

Donc 80 steps/mm à configurer via les commandes $100=80 et $101=80

nicolasdb commented 5 years ago

Reste

Solution temporaire,

  1. Soit allumer la machine = bouton noir ON/OFF, APRÈS avoir fait la connexion logicielle de l'arduino.
  2. Soit activer le bouton poussoir sur le module laser. Lorsque le module clignote rouge, c'est que le module est en low power pour régler le focus. Et ne sera pas activé lors de la connexion. Bouton poussoir blanc en bas à droite, à sa gauche, une led est rouge lorsque le module est sous tension (bouton off), clignote lorsque le mode low power est activé. (bouton on) image
nicolasdb commented 5 years ago

Bug de moteur qui ne sont pas mis sous tension. https://github.com/grbl/grbl/issues/589

Depio commented 5 years ago

Ok, Houston, we have a problem.

I order a second minilaser diode for fabmob but I was not please with the first one and I order the same used by bemaker this time. The machine is arrived, it's mounted but the laser module is lost somewhere. Hopefully, I bought earlier another laser module as safety parts. and because it's never easy and never work on the first attempt, connectors don't fit.

It's same same as the first (I was thinking) image

But with Eleksmaker, it's a 3pin cable for the same module but like this. image

The control board is the "SW-LD62 v2" And I found this part. image

Description: This PWM TO TTL laser module is design for EleksMaker series machine and its controller board. But it can also be used for other DIY machine which need to change TTL modulation. Specification: Power port size: 5.5*2.1mm Working voltage: DC 12V Woring power: >2A

Eleksmaker use the mana board controler. image

The other is laseraxes board. image Seems less good than the other. And the power supply connector is a bit loose, it doesn't match the size of the power supply (2.5mm vs 2.1mm probably, tssss) But have 2 place to connect laser, depending of the laser power. both 2pins. note: I have a second mana board... ^^

So my question is simply, "what about unsolder 2pin connector and solder 3pin connect instead?" Right?

I also got the two lasers (3pin and 4pin - Version).

I want to get it up and running without an external board. However, I have the problem that I can not disable the laser after connecting to the mains.

I have followed these instructions (https://www.instructables.com/id/Laser-Engraving-on-Your-Prusa-MK3/), but this does not work, nor does the connection of a simple power source and the subsequent removal does not turn off the laser. Only disconnecting the power source switches it off again.

nicolasdb commented 5 years ago

Ok, waw that's quite a hack. @satblip that could be interesting on the prusa :) Sorry, I saw I continued in french. I'm using issue also to take note during my process then I'm trying to summarize into a clean .md for my github page.

Logically, if the laser is controlled by using the same command as for the fan, using the yellow wire (TTL) it should work, yes... but carefull, like they said:

Some printers will have 12V (or even 24V) and you'll need to step that signal down to 5V, otherwise your laser's control module will burn out.

And I actually made this error because I didn't had the right connector and at some point I remember to put red wire on VCC but I changed cable (needed different length) and cables red/yellow was inverted and I put 12V on the TTL 5V. And I burned a capacitor.

Anyway, back to your problem. I'm actually not sure about the question. Is it to disable the laser when using the printer to print, right? If you don't want to disconnect the power supply, maybe a switch, because how they connected the laser, it's not possible to not send the same signal to the fan and the laser. Maybe, 5V is enough to trigger the laser at low power...

Depio commented 5 years ago

Ohh, you missunderstand me. Sorry.

My question: I bought the 3 pin laser to operate it as described in the manual.

This revealed the following phenomenon: I connected the laser to the 12V power supply. As soon as I did this, the laser turned on (as described in the description of the laser, this is also normal .. If you do not need the PWM function, you can connect directly to the power port to motor port (12V, GND) on your control board and leave the PWM port unconnected.)

Now I want to use the PWM signal, so I have, as described in the instructions, connected the cable and let the fan rotate. The laser is still fully on. If I deactivate the fan, the laser dims slowly, but then switches back to 100%. It seems to me that the laser processes the PWM signal, but as soon as there is no current at the TTL / PWM pin, the laser automatically switches to 100% (I will probably have to investigate this further)

I also tested to apply 5V to the TTL / PWM pin and then connect the 12V to turn on the laser. This too was unsuccessful. Turning off the 5V left the laser on.

I did the same test with a simple 5V power source. Here, no change in the brightness of the laser was recognizable, since this is just 5V (100% brightness) or 0V (unfortunately, 100% brightness).

After all this was unsuccessful, I ordered a second laser. Now the 4 pin version. Here was a similar phenomenon, which is why I can almost rule out a technical error on the laser almost. But so far I have no approach to finding a solution.

I hope someone can help, because a certain despair spreads at home currently.

At the supplier / dealer, I am unfortunately unaware of, as this itself apparently has no idea regarding the problem.

nicolasdb commented 5 years ago

Mmmm, right.

From what I learned from building, using and repairing the lasersaur, (100W CO2) The laser tube need power of course but also the TTL part to control the output. TTL could bet setup as turned ON when +5V or turned ON when 0V (well it's more >3V or <3V) https://nicolasdb.github.io/post/lasertech1/

Which could explain why on your module, it turn ON when fan OFF because maybe it need a High TTL signal to actually turn OFF the laser.... I'm guessing here. But, I never tried your setup. Here, I have tried the conversion from 2p+2p connectors to 3p used with the controller board Mana SE. and another module, which is without the driver board and it's activated by an analog 12V ON/OFF directly from the controller board (laseraxe) I never tried to apply power from an external source.

It seems to me that the laser processes the PWM signal, but as soon as there is no current at the TTL / PWM pin, the laser automatically switches to 100% (I will probably have to investigate this further)

Yes, don't forget about the PWM/TLL signal, it should be a constant voltage but with a modulation of frequency. It pulse. And without any control on this frequency, it could be always interpreted as "power ON at 100%" or Turned off in a low pulse, which could be low enough to stop the fan but not the laser. It will not show on a multimeter, You will just see the 5V, for frequency, I think you'll need an oscilloscope to look closely at the signal but try to test with different value of FAN speed.

satblip commented 5 years ago

Really nice hack to keep on the idea board for the future indeed! thx @Depio !

OldShark commented 5 years ago

Hi nicolasdb. Here I am with the same problem as you. I also bought an LD 2.5w that already comes with the 3-pin controller board. I can not make the laser intensity vary. This is using TTL or PWM. I'll see if tomorrow, I'll capture the image of the oscilloscope so you can see what happens.

OldShark commented 5 years ago

Other thing. I trying to use with an arduino uno, mana board.

nicolasdb commented 5 years ago

I'm not in the lab for a couple of weeks but I saw something engraved on the main body, it was mentionned if the laser was analog or digital. Since the diode is the same, Maybe driver boards are set depending on the use. Mmmm. no. Actually, the one engrave as analog power was without driver board and was controled directly from the main controller board.

The one I just solder a 3P connector instead of 2P2P worked perfectly (except I burn it afterward by inverting PWM and VCC ^^'

OldShark commented 5 years ago

With all certainty. I almost got tested. My luck is I saw before calling, because the signal on the oscilloscope was strange. If you put 12VDC on the TTL / PWM pin of this controller, it burns in the act. Hj at night I will see if I capture some images of what happens with the signal using as TTL or PWM. 5V direct on the TTL pin gives maximum power in the laser. It's good to use with a mosfet making role of relevancy and driven by pin 11 of the arduino. but only ON and OFF according to the modulation. but I really wanted to vary the power of the laser. I'm new to this. I have CNC 3D printer etc. But tinkering with laser I have now decided to do a CNC Laser.

diomark commented 5 years ago

Hi, I'm attempting to run the prusa mk3 laser engraver hack, but I'm a bit confused. I can't get the laser to power on (anything other then the dim test button) with the fan ttl connection.

My question is - for the 3-pin vcc/ground/ttl lasers, does the ttl get connected to the prusa fan's yellow line or the red line?

(i've tested w/ red power line and cant' get it to work:( asking before I take everything apart again..)

Thanks

nicolasdb commented 5 years ago

Sorry, I don't have experience on the prusa mk3 hack. Don't know If @Depio made it work. Or maybe @OldShark ?

diomark commented 5 years ago

I got it working, for others that may search here, it is indeed the red fan line not the yellow. The important part was adding a 1k resister between ground and ttl on the laser itself.. (I had initially added a 4.7k resistor which didn't work..)

OldShark commented 5 years ago

Hi diomark. Is your laser module the same as the image at the beginning of the topic?

OldShark commented 5 years ago

And i'm not using the driver that came with my laser. I'm controlling for pwm.

diomark commented 5 years ago

oldshark - i'm using this one - https://www.banggood.com/EleksMaker-FB03-500-500mW-Blue-Laser-Module-2_54-3P-TTLPWM-Modulation-for-DIY-Laser-Engraver-p-1266178.html?rmmds=myorder&cur_warehouse=CN seems to work fine, although to be honest so far I've only tested it on cardboard and paper.

OldShark commented 5 years ago

The driver is the same, my LD is 2.5w.

diomark commented 5 years ago

I just ordered that one too just to play with.. -m

On Tue, Jan 29, 2019 at 2:31 PM OldShark notifications@github.com wrote:

The driver is the same, my LD is 2.5w.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/openfab-lab/toolsDocs/issues/13#issuecomment-458733851, or mute the thread https://github.com/notifications/unsubscribe-auth/ATqrBdMGmgGy11ombzGNR996qiU4FE-4ks5vIMuqgaJpZM4W81Id .

OldShark commented 5 years ago

This year I want to buy a 15w.

OldShark commented 5 years ago

Where u from? Here is Brasil, São Paulo

djorimar commented 5 years ago

bonjour, je suis en galère grave je c’est pas ou brancher mon PWM /TLL? Quelqu'un peut m'aider. svp 7188UWSL0uL 700px-画板_1ef 53656001_2212156612205502_7993797056915308544_n

nicolasdb commented 5 years ago

tu peux donner un peu plus de détails? t'as 2 cartes controleurs? la verte c'est quoi? le driver?

djorimar commented 5 years ago

La verte c'est là où mon Lazer et brancher directement dessus.

nicolasdb commented 5 years ago

ok, donc carte noire = controleur, carte verte = driver laser. en toute logique, la puissance est fournie alors par le driver. donc le controleur ne doit envoyer que de l'info TTL/PWM en 5V. Donc, je pense que tu dois connecter ceci: image

à celà: image

Il est tjs conseiller de suivre aussi les polarités +- si c'est mentionné sur la carte.

djorimar commented 5 years ago

Je viens d'effectuer les branchements que vous venez de me conseiller, j'ai lancé une gravure et le laser ne s'allume pas

Le mer. 13 mars 2019 à 13:48, Nicolas de Barquin notifications@github.com a écrit :

ok, donc carte noire = controleur, carte verte = driver laser. en toute logique, la puissance est fournie alors par le driver. donc le controleur ne doit envoyer que de l'info TTL/PWM en 5V. Donc, je pense que tu dois connecter ceci: [image: image] https://user-images.githubusercontent.com/12049360/54279898-79a86200-4596-11e9-8cdc-e2ae283ca96e.png

à celà: [image: image] https://user-images.githubusercontent.com/12049360/54279924-89c04180-4596-11e9-81be-5fd081da6c9f.png

Il est tjs conseiller de suivre aussi les polarités +- si c'est mentionné sur la carte.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/openfab-lab/toolsDocs/issues/13#issuecomment-472407888, or mute the thread https://github.com/notifications/unsubscribe-auth/AuMsXo2WUqFCCu-_ydJUIE0FqEgXC1NSks5vWPOKgaJpZM4W81Id .

OldShark commented 5 years ago

Bonjour Djorimar et Nicolasdb. Pardon pour ingérence et pour mon pauvre Français. Nicolas D'après ce que je comprends, vous utilisez un contrôleur keyestudio, est-ce tout? Je pense qu'il a déjà une sortie pour contrôler le laser par PWM, mais je ne sais pas quelle est la tension, mais d'après ce que je vois devrait être 12V même. Dans ce cas, vous devrez le connecter à un pilote laser, tel que la carte verte. Certaines choses Quelle est la tension de fonctionnement de votre laser? Avez-vous un multimètre?

djorimar commented 5 years ago

Le français est bon merci. oui je pense aussi . Parque quand j'ai acheté la carte il y avez écrit .Oui j'ai un multimètre .

"Nouvelles fonctionnalités de la version v0.9 :

Le Baud Rate en série par défaut est désormais de 115 200. (au lieu de 9600) L'entrée limite de l'axe Z en D11 a été échangée avec une broche permettant à D12 de prendre en charge une sortie variable de PWM. Pas de file d'attente : La file d'attente a été retirée car elle est devenue redondante. La mise en attente met en pause Grbl et n'autorise que les commandes en temps réel. Le début du cycle reprend, et réinitialise les sorties. Nouvel algorithme par étapes fluide : Refonte complète de la manipulation du pilote d'étapes pour simplifier et réduire le temps de tâche par timing d'ISR. Mises à jour de la stabilité et la robustesse. Planification 4x plus rapide. Vitesse de rotation de sortie variable. Compilable via Arduino IDE. Refonde de l'analyseur syntaxique de la programmation de commande numérique : Entièrement réécrit pour une conformité totale à la programmation de commande numérique standard. Paramètres d'accélération et de vitesse indépendants. Limites douces : Vérifie si chaque commande de mouvement dépasse les limites de l'espace de travail avant de l'exécuter, et déclenche une alarme en cas de franchissement d'un seuil. Sonde : Les commandes de programmation numérique standard de sondes des G38.2, G38.3, G38.4 , Et G38.5 sont désormais prises en charge et connectées via la broche A5. Décalages de la longueur des outils. Performances Arc améliorées. Nouveau simulateur Grbl : Un wrapper complètement indépendant du code source principal de Grbl qui peut être compilé en un exécutable sur un ordinateur. Pas besoin d'Arduino. Il simule les réponses de Grbl comme s'il était sur un Arduino. Cartographie des broches du CPU. Rapports d'état configurables en temps réel. Retour à la position initiale mis à jour : Positionne le volume de l'espace de travail dans un espace négatif, quelle que soit la position limite de retour.

Contenu : 1 x Carte mère CNC keyestudio 1 câble USB Détails & caractéristiques

Le mer. 13 mars 2019 à 17:03, OldShark notifications@github.com a écrit :

Bonjour Djorimar et Nicolasdb. Pardon pour ingérence et pour mon pauvre Français. Nicolas D'après ce que je comprends, vous utilisez un contrôleur keyestudio, est-ce tout? Je pense qu'il a déjà une sortie pour contrôler le laser par PWM, mais je ne sais pas quelle est la tension, mais d'après ce que je vois devrait être 12V même. Dans ce cas, vous devrez le connecter à un pilote laser, tel que la carte verte. Certaines choses Quelle est la tension de fonctionnement de votre laser? Avez-vous un multimètre?

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/openfab-lab/toolsDocs/issues/13#issuecomment-472488202, or mute the thread https://github.com/notifications/unsubscribe-auth/AuMsXgwVDxUE5tRJvpyVpkatxxBS-ksfks5vWSFNgaJpZM4W81Id .

OldShark commented 5 years ago

Parfait, mais j'aimerais vraiment savoir quel est le problème. Je pensais que j'essayais de connecter la sortie du keyestudio à ce pilote laser. Je ne sais pas si cela fonctionnerait. Cette sortie laser de keyestudio doit être une MLI, car j’ai vu qu’elle pouvait aussi commander un moteur à courant continu.

djorimar commented 5 years ago

Mon problème c'est que je voudrais faire du nuances de gris.

Le mar. 12 mars 2019 à 12:56, Nicolas de Barquin notifications@github.com a écrit :

tu peux donner un peu plus de détails? t'as 2 cartes controleurs? la verte c'est quoi? le driver?

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/openfab-lab/toolsDocs/issues/13#issuecomment-471970296, or mute the thread https://github.com/notifications/unsubscribe-auth/AuMsXt7DsWSeUz0CVevdygXA0nwWbKpJks5vV5XygaJpZM4W81Id .

OldShark commented 5 years ago

J'ai compris. Et avec cette plaque photo vous ne pouvez pas? Et quel programme utilisez-vous? BemBox, LaserGRBL?

OldShark commented 5 years ago

En fait, TTL et PWM seront en niveaux de gris. L'un se fera par modulation d'impulsion et l'autre par intensité laser. Je l'utilise par PWM. Le pilote de mon laser étant gravé (TTL), je l’ai fait en utilisant PWM avec la broche 7 d’Arduino. Je fais varier l'intensité du laser, variant ainsi le degré de combustion du matériau.

kdm6182 commented 4 years ago

Help!!!! I'm new to laser engraving, I bought a 5.5w laser with ttl and mounted it on my anycubic i3 mega i connected the fan cable to the ttl and power to independent 12v supply. The ttl did not work at all. Then I connected the fan cable to the 12v input on the laser. It modulated the laser for a brief moment then turned off completely. Can any one suggest what's going wrong? Thanks

OldShark commented 4 years ago

Help!!!! I'm new to laser engraving, I bought a 5.5w laser with ttl and mounted it on my anycubic i3 mega i connected the fan cable to the ttl and power to independent 12v supply. The ttl did not work at all. Then I connected the fan cable to the 12v input on the laser. It modulated the laser for a brief moment then turned off completely. Can any one suggest what's going wrong? Thanks

Hello kdm. I don't know if this printer is based on arduino mega. What card does it use? You turned on the fan on ttl, you say the laser driver? Have phot of this wire to see? Where u from?

kdm6182 commented 4 years ago

Here is the link to the board on my printer. https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F302581784739 I connected the laser to separate 12v supply and connect the ttl to the fan power and tried to manipulate the pwm of the fan through gcode but the laser stays on at full power. Can't provide photos at the moment. Any ideas?

OldShark commented 4 years ago

Hi Kdm. I'm coming home now and couldn't see anything today. Much work. Very well. Let´s go! I think the problem is probably because FAN is not PWM controlled. Not sure, because I never used or want to see this 3D. Mine was the one I made and based on Arduino Mega. I believe the FAN control is only On / Off, to cool the extruder heatsink or PLA. Ru have a multimeter or oscilloscope? It would be interesting to actually measure the voltage being sent to your laser. Aliais saw no answer to the question of being directly connected to the laser or its driver. I don't think it's good for you to do this kind of test using the laser, especially using the driver. You can also instead use your laser module, use a piece of LED strip (12V), it will be the same because it is a diode. With the LED strip you can visually check the intensity change without danger.

fita-de-led-evo-12v-12w-m-amarelo-5-metros_1_1200

The problem I see with using your 3D is not having access to the board firmware. But back to your 3D. You can achieve grayscale only with On / Off state, but you would have to do so by varying the laser travel speed. It will not be simple to calibrate. Because the longer the laser lasts at one point, the more it will burn the material. If you have one of the equipment I mentioned earlier, test with your G-CODE to see what voltage variation you are getting and then post here.

And where u from? Cause u from Brazil, more simple to help u.

See this video. https://www.youtube.com/watch?v=JFH2zPe2mTM

kdm6182 commented 4 years ago

Hi I am in the UK. I will try the led trick. The fan must be pwm as you can directly control the fan speed from the 3d printer when it's printing. I have tested the fan cable on a multimeter and it reads 12v unconnected but as soon as I plug it into either the 12v or ttl port on the laser module it drops to 2.7v. It's very frustrating. Hope you can help.

OldShark commented 4 years ago

Oh My Gosh! I´m have the same problem with my laser module. 46152635-af1ff400-c271-11e8-99ac-ccd97b7a05bc

And i thinking i had burned my driver. LoL. Using a mosfet n to control then power by TTL. image

In my case i only remove the laser driver and wire mosfet pwm to laser direct. My TTL pulse comes from the pin 7 or 11 in arduino. only this. function perfectly. need only calibrate velocity. Realy make a simple table of velocity x material to brun.

Teste whit the LED and multimeter or oscilloscope.

OldShark commented 4 years ago

I still can't figure out why this DDP crash when connecting to the driver. and your case is exactly like mine, it drops to 50% of the voltage. If I'm not mistaken I commented here on Git, but no one could help me. This led me to use this solution. Test there and let's keep in touch. After all you are the first person I know with exactly the same problem as me. I don't even know if your driver is this. But I think it will do what you want. Good luck and keep me informed of pleaaaaaaase.

kdm6182 commented 4 years ago

I have done some more research on the board on my printer. And your thought on the fan not being pwm was correct. Apparently you can turn on soft pwm in marlin firmware but I'm hesitant to do this in case I mess things up. It's annoying as I replace my old printer with this one as the other nearly caught fire. And that one did have pwm. I was planning on building a cnc frame with arduino driver in the near future so think I will have to focus on that for it to work properly.

OldShark commented 4 years ago

Got it. The problem is, I don't see any TTL ports on your card really. But if it uses Marlin as firmware, it must be ATMega based. Surely there must be some lost TTL pin. Ideally an oscilloscope to figure it out. Make a CNC is good idea. I prefer GrBl to this. My CNC go to change to Mach3 now.

SK848667 commented 4 years ago

hi. can you help me please choose correct board.. let me explain my situation... i have prusa 3d printer and i bought a laser engraver to install on my 3d printer. but ones i received my laser i realized i ordered wrong one. Now i looking upgrade board for my laser... because, my laser has only 2 pins +/- 12v, but my printer which i need connect it has there only 5v (nozzle fan)... so i need board which will inlude 12v in and out and + 5v control... for example ones on my 3d printer fan is On, board will use dc from 12v inpute

OldShark commented 4 years ago

Hi sklymenko. Read this article and watch the videos https://endurancelasers.com/everything-about-ttl-and-laser-control/