search

raomin / ESPAltherma

Monitor your Daikin Altherma / ROTEX heat pump with ESP32
MIT License
356 stars 121 forks source link

Definition file for Altherma 3 LT EHVH-D6V #31

Closed rufik closed 3 years ago

rufik commented 3 years ago

I have new Altherma 3 LT model EHVH08S18DA6V and I'd like to try ESPAltherma with HA :) So I haven't found any information which definition file is most suitable for my model?

raomin commented 3 years ago

Hi @rufik, welcome! LT DA 08 I would go with ALTHERMA(LT_DA_04-08KW).h! Happy installation!

raomin commented 3 years ago

@rufik, is it ok with you? If so, you can close this issue :)

rufik commented 3 years ago

I've just collected all stuff needed and I'm gonna install & run this weekend - so let this issue be opened 2-3 days more please. I'll be back with feedback 😉

rufik commented 3 years ago

It looks like it's working quite fine, so let's close this issue right now 😁 I'm gonna take a closer look into values...

rufik commented 3 years ago

Just for the records - all attrs from this EHVH:

{
  "*Refrigerant type": "Conv 802 not avail.",
  "Override CMD:0x00 N_INV=1": "Conv 996 not avail.",
  "Override CMD:0x00 N_STD=0": "Conv 996 not avail.",
  "Override CMD:0x00 N_FAN=2": "Conv 996 not avail.",
  "Override CMD:0x00 N_EV=2": "Conv 996 not avail.",
  "Override CMD:0x00 N_20S=1": "Conv 996 not avail.",
  "Override CMD:0x00 N_CH=1": "Conv 996 not avail.",
  "Override CMD:0x00 N_SV=3": "Conv 996 not avail.",
  "Sensor Data Qty": "0",
  "INV compressor Qty": "0",
  "STD compressor Qty": "0",
  "Fan Data Qty": "0",
  "Expansion Valve Data Qty": "0",
  "4 Way Valve Data Qty": "0",
  "Crank Case Heater Qty": "0",
  "Solenoid valve Qty": "0",
  "Max. connectable indoor units": "0",
  "Connected Indoor Unit Qty": "0",
  "O/U MPU ID (xx)": "0",
  "O/U MPU ID (yy)": "0",
  "O/U capacity (kW)": "0",
  "NextDataGrid": "Conv 995 not avail.",
  "In-Out separator": "Conv 998 not avail.",
  "Override All Clear": "Conv 996 not avail.",
  "Operation Mode": "Heating",
  "Thermostat ON/OFF": "ON",
  "Restart standby": "OFF",
  "Startup Control": "OFF",
  "Defrost Operation": "OFF",
  "Oil Return Operation": "OFF",
  "Pressure equalizing operation": "OFF",
  "Demand Signal": "OFF",
  "Low noise control": "OFF",
  "Error type": "Warning",
  "Error Code": "AH",
  "Target Evap. Temp.": "21.0938",
  "Target Cond. Temp.": "0",
  "Discharge Temp. Drop": "OFF",
  "Discharge Temp. Protection Retry Qty": "Conv 310 not avail.",
  "Comp. INV Current Drop": "OFF",
  "Comp. INV Current Protection Retry Qty": "Conv 311 not avail.",
  "HP Drop Control": "OFF",
  "HP Protection Retry Qty": "Conv 310 not avail.",
  "LP Drop Control": "OFF",
  "LP Protection Retry Qty": "Conv 311 not avail.",
  "Fin Temp. Drop Control": "OFF",
  "Fin Temp. Protection Retry Qty": "Conv 310 not avail.",
  "Other Drop Control": "OFF",
  "Not in use": "46080",
  "O/U EEPROM (1st digit)": "Conv 215 not avail.",
  "O/U EEPROM (3rd 4th digit)": "Conv 215 not avail.",
  "O/U EEPROM (5th 6th digit)": "Conv 215 not avail.",
  "O/U EEPROM (7th 8th digit)": "Conv 215 not avail.",
  "O/U EEPROM (10th digit)": "Conv 215 not avail.",
  "O/U EEPROM (11th digit)": "Conv 214 not avail.",
  "Outdoor air temp.(R1T)": "-2.5",
  "O/U Heat Exch. Temp.": "0",
  "Discharge pipe temp.": "48",
  "Suction pipe temp.": "0",
  "Heat exchanger mid-temp.": "-8",
  "Liquid pipe temp.(R6T)": "0",
  "Heat sink temp.": "2.5",
  "Pressure sensor": "0",
  "Pressure sensor(T)": "Conv 405 not avail.",
  "INV primary current (A)": "7.3",
  "INV secondary current (A)": "7.3",
  "Voltage (N-phase) (V)": "230",
  "Brine Flow Switch": "OFF",
  "Brine inlet temp.": "-8",
  "Brine outlet temp.": "0",
  "Refrig. temp. evap. In": "0",
  "Refrig. temp. evap.Out": "0",
  "INV frequency (rps)": "56",
  "INV frequency 2 (rps)": "68",
  "STD Compressor 1": "OFF",
  "STD Compressor 2": "OFF",
  "Fan 1 (10 rpm)": "56",
  "Fan 2 (step)": "68",
  "Expansion valve (pls)": "17464",
  "Expansion valve 2 (pls)": "11008",
  "Expansion valve 3 (pls)": "1",
  "Expansion valve 4 (pls)": "0",
  "Expansion valve 5 (pls)": "0",
  "4 Way Valve 1": "OFF",
  "4 Way Valve 2": "OFF",
  "4 Way Valve 3": "ON",
  "4 Way Valve 4": "ON",
  "4 Way Valve 5": "ON",
  "Crank case heater 1": "OFF",
  "Crank case heater 2": "OFF",
  "Crank case heater 3": "ON",
  "Crank case heater 4": "ON",
  "Solenoid Valve 1": "OFF",
  "Solenoid Valve 2": "OFF",
  "Solenoid Valve 3": "ON",
  "Solenoid Valve 4": "ON",
  "Solenoid Valve 5": "ON",
  "Data Enable/Disable": "ON",
  "Indoor Unit Address": "0",
  "I/U operation mode": "Heating",
  "Freeze Protection": "OFF",
  "Silent Mode": "ON",
  "Freeze Protection for water piping": "OFF",
  "Error detailed code": "0",
  "I/U capacity code": "Conv 219 not avail.",
  "DHW setpoint": "45",
  "LW setpoint (main)": "29.9",
  "Water flow switch": "ON",
  "Thermal protector (Q1L) BUH": "ON",
  "Thermal protector BSH": "ON",
  "Benefit kWh rate power supply": "OFF",
  "Solar input": "OFF",
  "Bivalent Operation": "OFF",
  "2way valve(On:Heat_Off:Cool)": "OFF",
  "3way valve(On:DHW_Off:Space)": "OFF",
  "BSH": "OFF",
  "BUH Step1": "OFF",
  "BUH Step2": "OFF",
  "BPH": "OFF",
  "Water pump operation": "ON",
  "Solar pump operation": "OFF",
  "Indoor Option Code": "19",
  "I/U Software ID (xx)": "Conv 215 not avail.",
  "I/U Software ID (yy)": "Conv 215 not avail.",
  "I/U EEPROM Ver.": "0",
  "Leaving water temp. before BUH (R1T)": "29.1",
  "Leaving water temp. after BUH (R2T)": "29.5",
  "Refrig. Temp. liquid side (R3T)": "25.7",
  "Inlet water temp.(R4T)": "25",
  "DHW tank temp. (R5T)": "58.6",
  "Indoor ambient temp. (R1T)": "22",
  "Ext. indoor ambient sensor (R6T)": "0",
  "Reheat ON/OFF": "ON",
  "Storage eco ON/OFF": "OFF",
  "Storage comfort ON/OFF": "OFF",
  "Powerful DHW Operation. ON/OFF": "OFF",
  "Space heating Operation ON/OFF": "ON",
  "System OFF (ON:System off)": "OFF",
  "Emergency (indoor) active/not active": "OFF",
  "LW setpoint (add)": "45.4",
  "RT setpoint": "22.5",
  "Add. Ext. RT Input Cool.": "OFF",
  "Add. Ext. RT Input Heat.": "OFF",
  "Main RT Cooling": "OFF",
  "Main RT Heating": "OFF",
  "Pwr consumption limit 4": "OFF",
  "Pwr consumption limit 3": "OFF",
  "Pwr consumption limit 2": "OFF",
  "Pwr consumption limit 1": "OFF",
  "None": "OFF",
  "Tank preheat ON/OFF": "OFF",
  "Circulation pump operation": "OFF",
  "Alarm output": "OFF",
  "Space H Operation output": "ON",
  "Flow sensor (l/min)": "19.2",
  "Water pressure": "1.8",
  "Water pump signal (0:max-100:stop)": "4",
  "[Future] 3 way Valve Mixing 1": "0",
  "[Future] 3 way Valve Mixing 2": "0",
  "I/U EEPROM (3rd digit)": "Conv 215 not avail.",
  "I/U EEPROM (4th 5th digit)": "Conv 215 not avail.",
  "I/U EEPROM (6th 7th digit)": "Conv 215 not avail.",
  "I/U EEPROM (8th 9th digit)": "Conv 215 not avail.",
  "I/U EEPROM (11th digit)": "Conv 215 not avail.",
  "I/U EEPROM (12th digit)(rev.)": "Conv 214 not avail.",
  "Hybrid Op. Mode": "H/P only",
  "Boiler Operation Demand": "OFF",
  "Boiler DHW Demand": "OFF",
  "Bypass Valve Output": "ON",
  "BE_COP": "0",
  "Hybrid Heating Target Temp.": "0",
  "Boiler Heating Target Temp.": "29.9",
  "Add pump": "OFF",
  "Main pump": "OFF",
  "Mixed water temp.": "0",
  "2nd Domestic hot water temperature": "59.1",
  "Target delta T heating": "4",
  "Target delta T cooling": "5"
}

Heating is on (undefloor type), weather dependant, Madoka indoor thermostat. A lot of information :)

Renouveaux commented 2 years ago

HI @rufik,

Do you have connect your ESP on the X9 port ? Seem's I have same Heat Pump, but I haven't any X10 port, the X9 was a blue one.

Thank in advance for your replie.

rufik commented 2 years ago

It's X10A at mine, see pics attached. IMG_20210303_181712__01-01 IMG_20210316_135325-01

Renouveaux commented 2 years ago

Hi,

Thanks for your quick reply.

Seems to be a old PCB board. Mine was more little, so I have to check wich one have RX and TX.

Best regards

image

De : Rufik @.> Envoyé : vendredi 14 octobre 2022 05:41 À : raomin/ESPAltherma @.> Cc : Renouveaux @.>; Comment @.> Objet : Re: [raomin/ESPAltherma] Definition file for Altherma 3 LT EHVH-D6V (#31)

It's X10A at mine, see pics attached. [IMG_20210303_181712__01-01]https://user-images.githubusercontent.com/425558/195770720-ab072c02-ff9a-4a1d-b5b9-80a6eb8e93aa.jpeg [IMG_20210316_135325-01]https://user-images.githubusercontent.com/425558/195770729-6fd460cc-891c-45e6-bb99-d6a35d9ca312.jpeg

— Reply to this email directly, view it on GitHubhttps://github.com/raomin/ESPAltherma/issues/31#issuecomment-1278510574, or unsubscribehttps://github.com/notifications/unsubscribe-auth/ABZ3NARZIC54SRTSEYXWHZLWDDW7HANCNFSM4YQ2VXWA. You are receiving this because you commented.Message ID: @.***>

rufik commented 2 years ago

Seems to be a old PCB board. Mine was more little, so I have to check wich one have RX and TX. Best regards https://user-images.githubusercontent.com/7583362/195792996-da5ecde6-c724-4391-9608-f349ecf2998c.png

Isn't it board attached to front case with LCD screen? If yes, it's not that board you're looking for :) The proper board is behind the shield AFAIR, on the main unit.

Renouveaux commented 2 years ago

Oh, ok, I will open my unit to see what's inside. Because yes, you are right, I'm looking on the part with LCD screen.

Thanks a lot for your time