KonstaT
commented
1 month ago Please read the relevant wiki page (https://github.com/raspberry-vanilla/android_local_manifest/wiki/USB-boot) that I've updated to cover booting from a NVME device.
Using dtoverlay=android-usb or dtoverlay=android-nvme is not supported in Raspberry Vanilla nor suggested in the project's relevant wiki page.
Hi, KonstaT
I download your code of AOSP 14 rpi5, build and burn it into a micro sd, it boots normally. But when I burn it into a nvme ssd, it boots failed.（I have added dtoverlay=android-nvme to /boot/config.txt）
The error is "kvm: exiting hardware virtualization"
Can you give me a suggestion?
By the way, I tried boot from usb ssd, and failed too. I have added dtoverlay=android-usb to /boot/config.txt, and change ramdisk/fstab.rpi5 according to https://github.com/raspberry-vanilla/android_local_manifest/wiki/USB-boot.
The full log failed with nvme ssd:
1.25 RPi: BOOTSYS release VERSION:6fe0b091 DATE: 2024/06/05 TIME: 16:41:49 1.29 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1717602109 serial 0b195ec1 boardrev d04170 stc 1629449 1.39 AON_RESET: 00000003 PM_RSTS 00000020 1.47 RP1_BOOT chip ID: 0x20001927 1.49 PM_RSTS: 0x00000020 1.49 part 00000000 reset_info 00000000 1.53 PMIC reset-event 00000000 rtc 0000001f alarm 00000000 enabled 0 1.59 uSD voltage 3.3V 1.78 Initialising SDRAM 'Micron' 32Gb x2 total-size: 64 Gbit 4267 1.82 DDR 4267 1 0 64 152 3.10 OTP boardrev d04170 bootrom a a 3.11 Customer key hash 0000000000000000000000000000000000000000000000000000000000000000 3.19 VC-JTAG unlocked 3.41 RP1_BOOT chip ID: 0x20001927
4.51 RP1_BOOT chip ID: 0x20001927 4.52 RP1_BOOT: fw size 25992 4.07 PCI2 init 4.07 PCI2 reset 4.51 PCIe scan 00001de4:00000001 4.52 RP1_CHIP_INFO 20001927
4.55 RPi: BOOTLOADER release VERSION:6fe0b091 DATE: 2024/06/05 TIME: 16:41:49 4.62 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1717602109 serial 0b195ec1 boardrev d04170 stc 4662204 4.72 AON_RESET: 00000003 PM_RSTS 00000020 4.76 PCIEx1: PWR 1 DET_WAKE 1 4.03 usb_pd_init status 3 4.03 USB_PD CONFIG 0 43 4.14 XHCI-STOP 4.14 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d 4.19 USBSTS 1 4.21 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d 4.26 xHC0 ports 3 slots 64 intrs 4 4.38 XHCI-STOP 4.38 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d 4.43 USBSTS 11 4.45 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d 4.50 xHC1 ports 3 slots 64 intrs 4 4.58 Boot mode: SD (01) order f46 4.58 USB2[2] 00020ae1 connected 4.09 USB2[2] 00200a03 connected enabled 4.09 USB2 root HUB port 2 init 4.31 DEV [01:00] 1.16 000000:02 class 0 VID 30fa PID 1701 4.45 HID [01:00] 1.16 000000:02 register HID 5.88 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 5.99 SD HOST: 200000000 CTL0: 0x00800f00 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 5.08 EMMC 5.08 SD retry 1 oc 0 5.32 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 5.41 SD retry 2 oc 0 5.65 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 5.74 SDV1 5.74 SD CMD: 0x371a0010 (55) 0x0 0x1fff0001 5.76 Failed to open device: 'sdcard' (cmd 371a0010 status 1fff0001) 5.82 Retry SD 1 6.12 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 6.23 SD HOST: 200000000 CTL0: 0x00800f00 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 6.32 EMMC 6.32 SD retry 1 oc 0 6.56 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 6.65 SD retry 2 oc 0 6.89 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 6.98 SDV1 6.98 SD CMD: 0x371a0010 (55) 0x0 0x1fff0001 6.00 Failed to open device: 'sdcard' (cmd 371a0010 status 1fff0001) 6.06 Boot mode: NVME (06) order f4 6.23 PCI1 init 6.23 PCI1 reset 6.79 PCIe scan 000015b7:00005005 6.79 PCIe scan 000015b7:00005005 6.85 VID 0x15b7 MN WDC PC SN520 SDAPMUW-128G-1001
6.88 NVME on 0 6.90 MBR: 0x00000800, 262144 type: 0x0c 6.93 MBR: 0x00040800, 4194304 type: 0x83 6.97 MBR: 0x00440800, 524288 type: 0x83 6.01 MBR: 0x004c0800, 9697280 type: 0x83 6.05 Trying partition: 0 6.09 type: 32 lba: 2048 'mkfs.fat' ' boot ' clusters 258078 (1) 6.14 rsc 32 fat-sectors 2017 root dir cluster 2 sectors 0 entries 0 6.20 FAT32 clusters 258078 6.24 [nvme] autoboot.txt not found 6.26 Select partition rsts 0 C(boot_partition) 0 EEPROM config 0 result 0 6.33 Trying partition: 0 6.35 type: 32 lba: 2048 'mkfs.fat' ' boot ' clusters 258078 (1) 6.41 rsc 32 fat-sectors 2017 root dir cluster 2 sectors 0 entries 0 6.48 FAT32 clusters 258078 6.52 Read config.txt bytes 395 hnd 0xff59 6.55 [nvme] pieeprom.upd not found 6.58 usb_max_current_enable default 0 max-current 3000 6.67 Read bcm2712-rpi-5-b.dtb bytes 76538 hnd 0xe9c0 6.69 dt-match: compatible: raspberrypi,5-model-b match: brcm,bcm2712 6.75 dt-match: compatible: brcm,bcm2712 match: brcm,bcm2712 6.82 Selecting USB low current limit
NOTICE: BL31: v2.6(release):v2.6-239-g2a9ede0bd NOTICE: BL31: Built : 14:26:57, Jun 22 2023 [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1] [ 0.000000] Linux version 6.1.90-g0a324995cf0f-v8 (build-user@build-host) (Android (10087095, +pgo, +bolt, +lto, -mlgo, based on r487747c) clang version 17.0.2 (https://android.googlesource.com/toolchain/llvm-project d9f89f4d16663d5012e5c09495f3b30ece3d2362), LLD 17.0.2) #1 SMP PREEMPT Mon Jun 24 16:04:48 UTC 2024 [ 0.000000] random: crng init done [ 0.000000] Machine model: Raspberry Pi 5 Model B Rev 1.0 [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x000000001ac00000, size 320 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: 0x000000001ac00000..0x000000002ebfffff ( 327680 KB ) map reusable linux,cma [ 0.000000] OF: reserved mem: 0x0000000000000000..0x000000000007ffff ( 512 KB ) nomap non-reusable atf@0 [ 0.000000] OF: reserved mem: 0x000000003fd16280..0x000000003fd162c4 ( 0 KB ) nomap non-reusable nvram@0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000001ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000007ffff] [ 0.000000] node 0: [mem 0x0000000000080000-0x000000003f7fffff] [ 0.000000] node 0: [mem 0x0000000040000000-0x00000001ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000001ffffffff] [ 0.000000] On node 0, zone DMA: 2048 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 30 pages/cpu s84392 r8192 d30296 u122880 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: detected: Hardware dirty bit management [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2062336 [ 0.000000] Kernel command line: reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 smsc95xx.macaddr=2C:CF:67:2A:5E:2E vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000 console=ttyAMA10,115200 no_console_suspend root=/dev/ram0 rootwait androidboot.hardware=rpi5 androidboot.selinux=permissive androidboot.serialno=f882e2410b195ec1 androidboot.btmacaddr=11:22:0b:19:5e:c1 [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB) [ 0.000000] Memory: 7790140K/8380416K available (18560K kernel code, 2334K rwdata, 6884K rodata, 1984K init, 1478K bss, 262596K reserved, 327680K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 53372 entries in 209 pages [ 0.000000] ftrace: allocated 209 pages with 4 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns [ 0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns [ 0.000200] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval) [ 0.000245] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000) [ 0.000250] pid_max: default: 32768 minimum: 301 [ 0.000279] LSM: Security Framework initializing [ 0.000288] SELinux: Initializing. [ 0.000360] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000380] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000788] cgroup: Disabling memory control group subsystem [ 0.001249] cblist_init_generic: Setting adjustable number of callback queues. [ 0.001251] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.001280] cblist_init_generic: Setting adjustable number of callback queues. [ 0.001281] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.001308] cblist_init_generic: Setting adjustable number of callback queues. [ 0.001309] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.001373] rcu: Hierarchical SRCU implementation. [ 0.001374] rcu: Max phase no-delay instances is 1000. [ 0.002043] EFI services will not be available. [ 0.002142] smp: Bringing up secondary CPUs ... [ 0.002337] Detected PIPT I-cache on CPU1 [ 0.002386] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1] [ 0.002606] Detected PIPT I-cache on CPU2 [ 0.002648] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1] [ 0.002854] Detected PIPT I-cache on CPU3 [ 0.002892] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1] [ 0.002920] smp: Brought up 1 node, 4 CPUs [ 0.002923] SMP: Total of 4 processors activated. [ 0.002925] CPU features: detected: 32-bit EL0 Support [ 0.002927] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.002929] CPU features: detected: Common not Private translations [ 0.002930] CPU features: detected: CRC32 instructions [ 0.002932] CPU features: detected: RCpc load-acquire (LDAPR) [ 0.002933] CPU features: detected: LSE atomic instructions [ 0.002934] CPU features: detected: Privileged Access Never [ 0.002936] CPU features: detected: RAS Extension Support [ 0.002938] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.002971] CPU: All CPU(s) started at EL2 [ 0.002972] alternatives: applying system-wide alternatives [ 0.007286] devtmpfs: initialized [ 0.010386] Enabled cp15_barrier support [ 0.010392] Enabled setend support [ 0.010458] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.010464] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.013993] pinctrl core: initialized pinctrl subsystem [ 0.014196] DMI not present or invalid. [ 0.014361] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.014805] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations [ 0.014864] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.014901] audit: initializing netlink subsys (disabled) [ 0.014956] audit: type=2000 audit(0.012:1): state=initialized audit_enabled=0 res=1 [ 0.015087] thermal_sys: Registered thermal governor 'step_wise' [ 0.015101] cpuidle: using governor menu [ 0.015169] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.015201] ASID allocator initialised with 32768 entries [ 0.015506] Serial: AMBA PL011 UART driver [ 0.016477] bcm2835-mbox 107c013880.mailbox: mailbox enabled [ 0.016810] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 15, base_baud = 0) is a PL011 rev2 [ 0.778833] printk: console [ttyAMA10] enabled [ 0.791300] raspberrypi-firmware soc:firmware: Attached to firmware from 2024-06-05T15:41:49, variant start_cd [ 0.805351] raspberrypi-firmware soc:firmware: Firmware hash is 6fe0b09100000000000000000000000000000000 [ 0.821388] KASLR enabled [ 0.835495] bcm2835-dma 1000010000.dma: DMA legacy API manager, dmachans=0x1 [ 0.843217] iommu: Default domain type: Translated [ 0.848112] iommu: DMA domain TLB invalidation policy: strict mode [ 0.854505] SCSI subsystem initialized [ 0.858308] usbcore: registered new interface driver usbfs [ 0.863821] usbcore: registered new interface driver hub [ 0.869156] usbcore: registered new device driver usb [ 0.874276] usb_phy_generic phy: supply vcc not found, using dummy regulator [ 0.881477] mc: Linux media interface: v0.10 [ 0.885771] videodev: Linux video capture interface: v2.00 [ 0.891292] pps_core: LinuxPPS API ver. 1 registered [ 0.896274] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.905445] PTP clock support registered [ 0.909474] Advanced Linux Sound Architecture Driver Initialized. [ 0.915734] Bluetooth: Core ver 2.22 [ 0.919322] NET: Registered PF_BLUETOOTH protocol family [ 0.924651] Bluetooth: HCI device and connection manager initialized [ 0.931028] Bluetooth: HCI socket layer initialized [ 0.935920] Bluetooth: L2CAP socket layer initialized [ 0.940989] Bluetooth: SCO socket layer initialized [ 0.945988] vgaarb: loaded [ 0.948804] clocksource: Switched to clocksource arch_sys_counter [ 0.955061] VFS: Disk quotas dquot_6.6.0 [ 0.959011] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.965947] FS-Cache: Loaded [ 0.968891] CacheFiles: Loaded [ 0.972213] NET: Registered PF_INET protocol family [ 0.977284] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.987208] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.995814] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.003594] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 1.011819] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 1.020838] TCP: Hash tables configured (established 65536 bind 65536) [ 1.027546] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, linear) [ 1.035162] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 1.042075] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 1.049477] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.055326] PCI: CLS 0 bytes, default 64 [ 1.059377] Trying to unpack rootfs image as initramfs... [ 1.064838] hw perfevents: enabled with armv8_cortex_a76 PMU driver, 7 counters available [ 1.073179] kvm [1]: IPA Size Limit: 40 bits [ 1.077520] kvm [1]: vgic interrupt IRQ9 [ 1.081492] kvm [1]: VHE mode initialized successfully [ 1.087204] Initialise system trusted keyrings [ 1.091739] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 1.096719] Freeing initrd memory: 1616K [ 1.100329] zbud: loaded [ 1.105448] Key type cifs.idmap registered [ 1.109589] fuse: init (API version 7.37) [ 1.130497] Key type asymmetric registered [ 1.134607] Asymmetric key parser 'x509' registered [ 1.139513] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 1.146984] io scheduler mq-deadline registered [ 1.151530] io scheduler kyber registered [ 1.155796] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7c502000, parent irq: 30) [ 1.164943] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d503000, parent irq: 31) [ 1.172679] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508380, parent irq: 32) [ 1.180409] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508400, parent irq: 33) [ 1.188153] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7d510600, parent irq: 34) [ 1.197286] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d517b00, parent irq: 35) [ 1.205945] gpio-461 (RP1 RUN pin): hogged as output/high [ 1.211871] simple-framebuffer 3f800000.framebuffer: framebuffer at 0x3f800000, 0x3f4800 bytes [ 1.220522] simple-framebuffer 3f800000.framebuffer: format=r5g6b5, mode=1920x1080x16, linelength=3840 [ 1.229906] simple-framebuffer 3f800000.framebuffer: fb0: simplefb registered! [ 1.271968] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled [ 1.278600] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 37, base_baud = 6000000) is a 16550A [ 1.287903] serial serial0: tty port ttyS0 registered [ 1.293276] iproc-rng200 107d208000.rng: hwrng registered [ 1.298758] vc-mem: phys_addr:0x00000000 mem_base=0x3fc00000 mem_size:0x40000000(1024 MiB) [ 1.307240] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040 [ 1.315046] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1 [ 1.322669] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040 [ 1.330469] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2 [ 1.338090] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020 [ 1.345890] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3 [ 1.353511] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020 [ 1.361311] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4 [ 1.369075] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe [ 1.379968] brd: module loaded [ 1.384674] loop: module loaded [ 1.387989] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver [ 1.395472] Loading iSCSI transport class v2.0-870. [ 1.401588] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 1.409456] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved. [ 1.419783] tun: Universal TUN/TAP device driver, 1.6 [ 1.425093] usbcore: registered new interface driver brcmfmac [ 1.430869] usbcore: registered new device driver r8152-cfgselector [ 1.437166] usbcore: registered new interface driver r8152 [ 1.442677] usbcore: registered new interface driver lan78xx [ 1.448362] usbcore: registered new interface driver asix [ 1.453789] usbcore: registered new interface driver ax88179_178a [ 1.459910] usbcore: registered new interface driver cdc_ether [ 1.465771] usbcore: registered new interface driver smsc95xx [ 1.471542] usbcore: registered new interface driver net1080 [ 1.477227] usbcore: registered new interface driver cdc_subset [ 1.483173] usbcore: registered new interface driver zaurus [ 1.488772] usbcore: registered new interface driver cdc_ncm [ 1.494465] usbcore: registered new interface driver r8153_ecm [ 1.500421] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ 1.507491] dwc2 1000480000.usb: supply vusb_d not found, using dummy regulator [ 1.514872] dwc2 1000480000.usb: supply vusb_a not found, using dummy regulator [ 1.622448] dwc2 1000480000.usb: EPs: 8, dedicated fifos, 4080 entries in SPRAM [ 1.629957] usbcore: registered new interface driver cdc_acm [ 1.635636] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.643714] usbcore: registered new interface driver uas [ 1.649055] usbcore: registered new interface driver usb-storage [ 1.655105] usbcore: registered new interface driver cp210x [ 1.660700] usbserial: USB Serial support registered for cp210x [ 1.666646] usbcore: registered new interface driver pl2303 [ 1.672239] usbserial: USB Serial support registered for pl2303 [ 1.678317] mousedev: PS/2 mouse device common for all mice [ 1.683924] usbcore: registered new interface driver xpad [ 1.689348] usbcore: registered new interface driver usb_acecad [ 1.695294] usbcore: registered new interface driver aiptek [ 1.700900] usbcore: registered new interface driver hanwang [ 1.706586] usbcore: registered new interface driver kbtab [ 1.712117] usbcore: registered new interface driver usbtouchscreen [ 1.726987] rpi-rtc soc:rpi_rtc: registered as rtc0 [ 1.733416] rpi-rtc soc:rpi_rtc: setting system clock to 1970-01-01T00:00:42 UTC (42) [ 1.741304] i2c_dev: i2c /dev entries driver [ 1.745740] brcmstb-i2c 107d508200.i2c: @200000hz registered in interrupt mode [ 1.753185] brcmstb-i2c 107d508280.i2c: @200000hz registered in interrupt mode [ 1.760651] ir_imon_decoder: IR iMON protocol handler initialized [ 1.766768] IR JVC protocol handler initialized [ 1.771310] IR MCE Keyboard/mouse protocol handler initialized [ 1.777162] IR NEC protocol handler initialized [ 1.781705] IR RC5(x/sz) protocol handler initialized [ 1.786772] IR RC6 protocol handler initialized [ 1.791314] IR RCMM protocol handler initialized [ 1.795944] IR SANYO protocol handler initialized [ 1.800661] IR Sharp protocol handler initialized [ 1.805378] IR Sony protocol handler initialized [ 1.810008] IR XMP protocol handler initialized [ 1.814661] usbcore: registered new interface driver uvcvideo [ 1.820871] bcm2835-wdt bcm2835-wdt: Poweroff handler already present! [ 1.827425] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer [ 1.833844] device-mapper: uevent: version 1.0.3 [ 1.838539] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 1.847059] Bluetooth: HCI UART driver ver 2.3 [ 1.851518] Bluetooth: HCI UART protocol H4 registered [ 1.856699] Bluetooth: HCI UART protocol Broadcom registered [ 1.856744] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator [ 1.869858] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator [ 1.877459] sdhci: Secure Digital Host Controller Interface driver [ 1.883683] sdhci: Copyright(c) Pierre Ossman [ 1.888113] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.893932] ledtrig-cpu: registered to indicate activity on CPUs [ 1.899992] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.906467] hid: raw HID events driver (C) Jiri Kosina [ 1.912062] usbcore: registered new interface driver usbhid [ 1.917657] usbhid: USB HID core driver [ 1.921621] ashmem: initialized [ 1.924805] SPI driver st-accel-spi has no spi_device_id for st,lis302dl-spi [ 1.931882] SPI driver st-accel-spi has no spi_device_id for st,lis3lv02dl-accel [ 1.939304] SPI driver st-accel-spi has no spi_device_id for st,lis3dh-accel [ 1.946379] SPI driver st-accel-spi has no spi_device_id for st,lsm330d-accel [ 1.953540] SPI driver st-accel-spi has no spi_device_id for st,lsm330dl-accel [ 1.960789] SPI driver st-accel-spi has no spi_device_id for st,lsm330dlc-accel [ 1.968124] SPI driver st-accel-spi has no spi_device_id for st,lis331dlh-accel [ 1.975460] SPI driver st-accel-spi has no spi_device_id for st,lsm330-accel [ 1.982533] SPI driver st-accel-spi has no spi_device_id for st,lsm303agr-accel [ 1.989869] SPI driver st-accel-spi has no spi_device_id for st,lis2dh12-accel [ 1.997117] SPI driver st-accel-spi has no spi_device_id for st,lng2dm-accel [ 2.004192] SPI driver st-accel-spi has no spi_device_id for st,h3lis331dl-accel [ 2.011615] SPI driver st-accel-spi has no spi_device_id for st,lis331dl-accel [ 2.018902] SPI driver st-magn-spi has no spi_device_id for st,lis3mdl-magn [ 2.025888] SPI driver st-magn-spi has no spi_device_id for st,lsm303agr-magn [ 2.033050] SPI driver st-magn-spi has no spi_device_id for st,lsm9ds1-magn [ 2.040042] SPI driver bmp280 has no spi_device_id for bosch,bmp085 [ 2.046400] usbcore: registered new interface driver snd-usb-audio [ 2.053034] Mirror/redirect action on [ 2.056705] netem: version 1.3 [ 2.059764] u32 classifier [ 2.062473] input device check on [ 2.066141] Actions configured [ 2.070219] xt_time: kernel timezone is -0000 [ 2.074625] gre: GRE over IPv4 demultiplexor driver [ 2.079518] IPv4 over IPsec tunneling driver [ 2.083926] Initializing XFRM netlink socket [ 2.088210] IPsec XFRM device driver [ 2.091900] NET: Registered PF_INET6 protocol family [ 2.097190] Segment Routing with IPv6 [ 2.100865] In-situ OAM (IOAM) with IPv6 [ 2.104818] mip6: Mobile IPv6 [ 2.107896] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.114007] NET: Registered PF_PACKET protocol family [ 2.119076] NET: Registered PF_KEY protocol family [ 2.123889] Key type dns_resolver registered [ 2.128396] registered taskstats version 1 [ 2.132517] Loading compiled-in X.509 certificates [ 2.137390] Key type .fscrypt registered [ 2.141323] Key type fscrypt-provisioning registered [ 2.147024] brcm-pcie 1000110000.pcie: host bridge /axi/pcie@110000 ranges: [ 2.154020] brcm-pcie 1000110000.pcie: No bus range found for /axi/pcie@110000, using [bus 00-ff] [ 2.163110] brcm-pcie 1000110000.pcie: MEM 0x1b00000000..0x1bfffffffb -> 0x0000000000 [ 2.171408] brcm-pcie 1000110000.pcie: MEM 0x1800000000..0x1affffffff -> 0x0400000000 [ 2.179716] brcm-pcie 1000110000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000 [ 2.189175] brcm-pcie 1000110000.pcie: setting SCB_ACCESS_EN, READ_UR_MODE, MAX_BURST_SIZE [ 2.197489] brcm-pcie 1000110000.pcie: Forcing gen 2 [ 2.202506] brcm-pcie 1000110000.pcie: PCI host bridge to bus 0000:00 [ 2.208975] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.214485] pci_bus 0000:00: root bus resource [mem 0x1b00000000-0x1bfffffffb] (bus address [0x00000000-0xfffffffb]) [ 2.225062] pci_bus 0000:00: root bus resource [mem 0x1800000000-0x1affffffff pref] (bus address [0x400000000-0x6ffffffff]) [ 2.236256] pci 0000:00:00.0: [14e4:2712] type 01 class 0x060400 [ 2.242320] pci 0000:00:00.0: PME# supported from D0 D3hot [ 2.247837] Bluetooth: hci0: BCM: chip id 107 [ 2.248509] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.260446] Bluetooth: hci0: BCM: features 0x2f [ 2.266049] Bluetooth: hci0: BCM4345C0 [ 2.269807] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0000 [ 2.275781] Bluetooth: hci0: BCM4345C0 'brcm/BCM4345C0.hcd' Patch [ 2.364815] brcm-pcie 1000110000.pcie: link up, 5.0 GT/s PCIe x1 (!SSC) [ 2.371482] pci 0000:01:00.0: [15b7:5005] type 00 class 0x010802 [ 2.377574] pci 0000:01:00.0: reg 0x10: [mem 0x1b00000000-0x1b00003fff 64bit] [ 2.384913] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 15.752 Gb/s with 8.0 GT/s PCIe x2 link) [ 2.408821] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.415477] pci 0000:00:00.0: BAR 8: assigned [mem 0x1b00000000-0x1b000fffff] [ 2.422659] pci 0000:01:00.0: BAR 0: assigned [mem 0x1b00000000-0x1b00003fff 64bit] [ 2.430363] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.435362] pci 0000:00:00.0: bridge window [mem 0x1b00000000-0x1b000fffff] [ 2.442544] pci 0000:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 2.451035] pci 0000:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 2.459559] pcieport 0000:00:00.0: enabling device (0000 -> 0002) [ 2.465706] pcieport 0000:00:00.0: PME: Signaling with IRQ 42 [ 2.471555] pcieport 0000:00:00.0: AER: enabled with IRQ 42 [ 2.477267] nvme nvme0: pci function 0000:01:00.0 [ 2.482011] nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 2.487803] brcm-pcie 1000110000.pcie: clkreq control enabled [ 2.493635] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@120000 ranges: [ 2.500625] brcm-pcie 1000120000.pcie: No bus range found for /axi/pcie@120000, using [bus 00-ff] [ 2.509712] brcm-pcie 1000120000.pcie: MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000 [ 2.518011] brcm-pcie 1000120000.pcie: MEM 0x1c00000000..0x1effffffff -> 0x0400000000 [ 2.526311] brcm-pcie 1000120000.pcie: IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000 [ 2.534612] brcm-pcie 1000120000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000 [ 2.543085] nvme nvme0: 4/0/0 default/read/poll queues [ 2.543972] brcm-pcie 1000120000.pcie: setting SCB_ACCESS_EN, READ_UR_MODE, MAX_BURST_SIZE [ 2.550707] nvme0n1: p1 p2 p3 p4 [ 2.556549] brcm-pcie 1000120000.pcie: Forcing gen 2 [ 2.564875] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0001:00 [ 2.571339] pci_bus 0001:00: root bus resource [bus 00-ff] [ 2.576843] pci_bus 0001:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb]) [ 2.587407] pci_bus 0001:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff]) [ 2.598589] pci 0001:00:00.0: [14e4:2712] type 01 class 0x060400 [ 2.604631] pci 0001:00:00.0: PME# supported from D0 D3hot [ 2.610810] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.724816] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC) [ 2.731473] pci 0001:01:00.0: [1de4:0001] type 00 class 0x020000 [ 2.737527] pci 0001:01:00.0: reg 0x10: [mem 0xffffc000-0xffffffff] [ 2.743827] pci 0001:01:00.0: reg 0x14: [mem 0xffc00000-0xffffffff] [ 2.750124] pci 0001:01:00.0: reg 0x18: [mem 0xffff0000-0xffffffff] [ 2.756481] pci 0001:01:00.0: supports D1 [ 2.760500] pci 0001:01:00.0: PME# supported from D0 D1 D3hot D3cold [ 2.776811] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.783461] pci 0001:00:00.0: BAR 8: assigned [mem 0x1f00000000-0x1f005fffff] [ 2.790636] pci 0001:01:00.0: BAR 1: assigned [mem 0x1f00000000-0x1f003fffff] [ 2.797810] pci 0001:01:00.0: BAR 2: assigned [mem 0x1f00400000-0x1f0040ffff] [ 2.804974] pci 0001:01:00.0: BAR 0: assigned [mem 0x1f00410000-0x1f00413fff] [ 2.812146] pci 0001:00:00.0: PCI bridge to [bus 01] [ 2.817132] pci 0001:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff] [ 2.824298] pci 0001:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512 [ 2.832776] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512 [ 2.841300] pcieport 0001:00:00.0: enabling device (0000 -> 0002) [ 2.847439] pcieport 0001:00:00.0: PME: Signaling with IRQ 48 [ 2.853264] pcieport 0001:00:00.0: AER: enabled with IRQ 48 [ 2.858913] rp1 0001:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200 [ 2.867996] rp1 0001:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200 [ 2.877256] rp1 0001:01:00.0: enabling device (0000 -> 0002) [ 2.883568] rp1 0001:01:00.0: chip_id 0x20001927 [ 2.905962] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 116 (2c:cf:67:2a:5e:2e) [ 2.917738] dw_axi_dmac_platform 1f00188000.dma: DesignWare AXI DMA Controller, 8 channels [ 2.926278] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 2.931363] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1 [ 2.939053] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000010810 [ 2.948058] xhci-hcd xhci-hcd.0: irq 141, io mem 0x1f00200000 [ 2.953887] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 2.958963] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2 [ 2.966212] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed [ 2.972361] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 2.980667] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.987918] usb usb1: Product: xHCI Host Controller [ 2.992821] usb usb1: Manufacturer: Linux 6.1.90-g0a324995cf0f-v8 xhci-hcd [ 2.999725] usb usb1: SerialNumber: xhci-hcd.0 [ 3.004294] hub 1-0:1.0: USB hub found [ 3.008063] hub 1-0:1.0: 2 ports detected [ 3.012186] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 3.020486] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.027734] usb usb2: Product: xHCI Host Controller [ 3.032627] usb usb2: Manufacturer: Linux 6.1.90-g0a324995cf0f-v8 xhci-hcd [ 3.039588] usb usb2: SerialNumber: xhci-hcd.0 [ 3.044118] hub 2-0:1.0: USB hub found [ 3.047883] hub 2-0:1.0: 1 port detected [ 3.052071] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 3.057250] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3 [ 3.064930] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000010810 [ 3.074033] xhci-hcd xhci-hcd.1: irq 146, io mem 0x1f00300000 [ 3.079863] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 3.084933] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4 [ 3.092281] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed [ 3.093435] Bluetooth: hci0: BCM: features 0x2f [ 3.098419] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 3.104242] Bluetooth: hci0: BCM43455 37.4MHz Raspberry Pi 3+-0190 [ 3.112806] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.117433] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0382 [ 3.124680] usb usb3: Product: xHCI Host Controller [ 3.135513] usb usb3: Manufacturer: Linux 6.1.90-g0a324995cf0f-v8 xhci-hcd [ 3.142419] usb usb3: SerialNumber: xhci-hcd.1 [ 3.142418] Bluetooth: hci0: BCM: Using default device address (43:45:c0:00:1f:ac) [ 3.154570] hub 3-0:1.0: USB hub found [ 3.158339] hub 3-0:1.0: 2 ports detected [ 3.162459] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 3.170761] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.178010] usb usb4: Product: xHCI Host Controller [ 3.182901] usb usb4: Manufacturer: Linux 6.1.90-g0a324995cf0f-v8 xhci-hcd [ 3.189820] usb usb4: SerialNumber: xhci-hcd.1 [ 3.194354] hub 4-0:1.0: USB hub found [ 3.198121] hub 4-0:1.0: 1 port detected [ 3.202192] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000 [ 3.209993] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0 [ 3.217924] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774 [ 3.226185] platform 1000800000.codec: bcm2712_iommu_probe_device: MMU 1000005100.iommu [ 3.234219] platform 1000800000.codec: bcm2712_iommu_device_group: MMU 1000005100.iommu [ 3.242255] platform 1000800000.codec: Adding to iommu group 0 [ 3.248119] platform 1000880000.pisp_be: bcm2712_iommu_probe_device: MMU 1000005100.iommu [ 3.256327] platform 1000880000.pisp_be: bcm2712_iommu_device_group: MMU 1000005100.iommu [ 3.264539] platform 1000880000.pisp_be: Adding to iommu group 0 [ 3.270584] platform 1000800000.codec: bcm2712_iommu_attach_dev: MMU 1000005100.iommu [ 3.278445] platform 1000880000.pisp_be: bcm2712_iommu_attach_dev: MMU 1000005100.iommu [ 3.286481] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success [ 3.293536] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774 [ 3.301788] platform axi:gpu: bcm2712_iommu_probe_device: MMU 1000005200.iommu [ 3.309062] platform axi:gpu: bcm2712_iommu_device_group: MMU 1000005200.iommu [ 3.316317] platform axi:gpu: Adding to iommu group 1 [ 3.321407] platform axi:gpu: bcm2712_iommu_attach_dev: MMU 1000005200.iommu [ 3.328504] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success [ 3.335515] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774 [ 3.343764] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success [ 3.355546] [drm] Initialized v3d 1.0.0 20180419 for 1002000000.v3d on minor 0 [ 3.367838] vc4-drm axi:gpu: bcm2712_iommu_of_xlate: MMU 1000005200.iommu [ 3.380666] vc4-drm axi:gpu: bound 107c580000.hvs (ops vc4_hvs_ops) [ 3.392825] vc4-drm axi:gpu: bound 107c701400.hdmi (ops vc4_hdmi_ops) [ 3.401824] vc4-drm axi:gpu: bound 107c706400.hdmi (ops vc4_hdmi_ops) [ 3.408345] vc4-drm axi:gpu: bound 107c500000.mop (ops vc4_txp_ops) [ 3.414670] vc4-drm axi:gpu: bound 107c501000.moplet (ops vc4_txp_ops) [ 3.420806] usb 3-2: new low-speed USB device number 2 using xhci-hcd [ 3.421252] vc4-drm axi:gpu: bound 107c410000.pixelvalve (ops vc4_crtc_ops) [ 3.434710] vc4-drm axi:gpu: bound 107c411000.pixelvalve (ops vc4_crtc_ops) [ 3.491131] [drm] Initialized vc4 0.0.0 20140616 for axi:gpu on minor 1 [ 3.527752] vc4-drm axi:gpu: [drm] fb0: vc4drmfb frame buffer device [ 3.534313] pispbe 1000880000.pisp_be: bcm2712_iommu_of_xlate: MMU 1000005100.iommu [ 3.544862] pispbe 1000880000.pisp_be: pispbe_probe: HW version: 0x02252700 [ 3.551944] pispbe 1000880000.pisp_be: pispbe_probe: BatchStatus: 0x00000000 [ 3.559018] pispbe 1000880000.pisp_be: pispbe_probe: Status: 0x00000000 [ 3.566102] pispbe 1000880000.pisp_be: Register nodes for group 0 [ 3.572257] pispbe 1000880000.pisp_be: input device node registered as /dev/video20 [ 3.579987] pispbe 1000880000.pisp_be: tdn_input device node registered as /dev/video21 [ 3.588069] pispbe 1000880000.pisp_be: stitch_input device node registered as /dev/video22 [ 3.596396] pispbe 1000880000.pisp_be: hog_output device node registered as /dev/video23 [ 3.604543] pispbe 1000880000.pisp_be: output0 device node registered as /dev/video24 [ 3.612446] pispbe 1000880000.pisp_be: output1 device node registered as /dev/video25 [ 3.620350] pispbe 1000880000.pisp_be: tdn_output device node registered as /dev/video26 [ 3.628500] pispbe 1000880000.pisp_be: stitch_output device node registered as /dev/video27 [ 3.636921] pispbe 1000880000.pisp_be: config device node registered as /dev/video28 [ 3.644906] pispbe 1000880000.pisp_be: Register nodes for group 1 [ 3.651063] pispbe 1000880000.pisp_be: input device node registered as /dev/video29 [ 3.658765] usb 3-2: New USB device found, idVendor=30fa, idProduct=1701, bcdDevice= 1.00 [ 3.666981] usb 3-2: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 3.666985] pispbe 1000880000.pisp_be: tdn_input device node registered as /dev/video30 [ 3.674143] usb 3-2: Product: USB GAMING MOUSE [ 3.674144] usb 3-2: Manufacturer: INSTANT [ 3.690886] pispbe 1000880000.pisp_be: stitch_input device node registered as /dev/video31 [ 3.699244] pispbe 1000880000.pisp_be: hog_output device node registered as /dev/video32 [ 3.707681] pispbe 1000880000.pisp_be: output0 device node registered as /dev/video33 [ 3.715591] pispbe 1000880000.pisp_be: output1 device node registered as /dev/video34 [ 3.723494] pispbe 1000880000.pisp_be: tdn_output device node registered as /dev/video35 [ 3.731642] pispbe 1000880000.pisp_be: stitch_output device node registered as /dev/video36 [ 3.740172] pispbe 1000880000.pisp_be: config device node registered as /dev/video37 [ 3.748321] sdhci-brcmstb 1000fff000.mmc: there is not valid maps for state default [ 3.748589] rpivid 1000800000.codec: bcm2712_iommu_of_xlate: MMU 1000005100.iommu [ 3.756056] input: INSTANT USB GAMING MOUSE as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.0/0003:30FA:1701.0001/input/input0 [ 3.778180] mmc1: CQHCI version 5.10 [ 3.778223] mmc0: CQHCI version 5.10 [ 3.781778] rpivid 1000800000.codec: Device registered as /dev/video19 [ 3.781960] hid-generic 0003:30FA:1701.0001: input,hidraw0: USB HID v1.10 Mouse [INSTANT USB GAMING MOUSE ] on usb-xhci-hcd.1-2/input0 [ 3.805498] input: pwr_button as /devices/platform/pwr_button/input/input1 [ 3.812492] of_cfs_init [ 3.814962] of_cfs_init: OK [ 3.817804] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.821144] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit [ 3.825664] input: INSTANT USB GAMING MOUSE Keyboard as /devices/platform/axi/1000120000.pcie/1f00300000.usb/xhci-hcd.1/usb3/3-2/3-2:1.1/0003:30FA:1701.0002/input/input2 [ 3.849110] cfg80211: Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf' [ 3.858366] cfg80211: Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328' [ 3.868335] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.875056] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 3.883708] clk: Disabling unused clocks [ 3.891882] ALSA device list: [ 3.894854] #0: vc4-hdmi-0 [ 3.897745] #1: vc4-hdmi-1 [ 3.901595] uart-pl011 107d001000.serial: no DMA platform data [ 3.908897] hid-generic 0003:30FA:1701.0002: input,hiddev96,hidraw1: USB HID v1.10 Keyboard [INSTANT USB GAMING MOUSE ] on usb-xhci-hcd.1-2/input1 [ 3.971350] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit [ 3.981682] Freeing unused kernel memory: 1984K [ 3.986282] Run /init as init process [ 3.990898] init: init first stage started! [ 3.995159] init: Unable to open /lib/modules, skipping module loading. [ 4.001868] init: Copied ramdisk prop to /second_stage_resources/system/etc/ramdisk/build.prop [ 4.010551] init: [libfstab] Using Android DT directory /proc/device-tree/firmware/android/ [ 4.011676] mmc1: new ultra high speed DDR50 SDIO card at address 0001 [ 4.019532] init: Failed to read vbmeta partitions. [ 4.031748] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 4.037067] init: DSU not detected, proceeding with normal boot [ 4.040456] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,5-model-b.bin failed with error -2 [ 4.046827] init: [libfs_mgr] superblock s_max_mnt_count:65535,/dev/block/nvme0n1p2 [ 4.066734] EXT4-fs (nvme0n1p2): mounted filesystem without journal. Quota mode: none. [ 4.074704] init: [libfs_mgr] __mount(source=/dev/block/nvme0n1p2,target=/system,type=ext4)=0: Success [ 4.084181] init: Switching root to '/system' [ 4.089484] init: [libfs_mgr] failed to realpath(/boot): No such file or directory [ 4.103804] kvm: exiting hardware virtualization [ 4.246215] reboot: Restarting system with command 'bootloader'
1.25 RPi: BOOTSYS release VERSION:6fe0b091 DATE: 2024/06/05 TIME: 16:41:49 1.29 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1717602109 serial 0b195ec1 boardrev d04170 stc 1629449 1.39 AON_RESET: 00000003 PM_RSTS 00000020 1.47 RP1_BOOT chip ID: 0x20001927 1.49 PM_RSTS: 0x00000020 1.49 part 00000000 reset_info 00000000 1.53 PMIC reset-event 00000000 rtc 0000002e alarm 00000000 enabled 0 1.59 uSD voltage 3.3V 1.78 Initialising SDRAM 'Micron' 32Gb x2 total-size: 64 Gbit 4267 1.82 DDR 4267 1 0 64 152 3.17 OTP boardrev d04170 bootrom a a 3.19 Customer key hash 0000000000000000000000000000000000000000000000000000000000000000 3.26 VC-JTAG unlocked 3.49 RP1_BOOT chip ID: 0x20001927