issues
search
scottc11
/
ok-dev-board
0
stars
0
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
When loading a saved sequence, device will freeze after the sequence loops once
#212
scottc11
closed
1 year ago
0
Firmware update dec 2022
#211
scottc11
closed
1 year ago
0
Gesture for clearing 1VO Calibration Data (ALT + Cal. 1vo + Clear Conf.)
#210
scottc11
opened
1 year ago
0
Gesture for clearing Bender Calibration (ALT + Bend Mode + Clear Conf.)
#209
scottc11
closed
1 year ago
1
Store octave position in flash
#208
scottc11
opened
1 year ago
0
when holding channel select and in quantizer mode, touching a touch pad overrides the quantizing and sustains that note
#207
scottc11
closed
1 year ago
0
ALT Firmware
#206
scottc11
opened
1 year ago
1
Jumper Option: Octave shifts don't trigger the gate
#205
scottc11
opened
1 year ago
0
Need a way to add silence into a sequence
#204
scottc11
opened
1 year ago
0
CV Mode button doesn't cycle through the modes
#203
scottc11
closed
1 year ago
1
How do all the alternate functions and menues react when record is enabled?
#202
scottc11
closed
1 year ago
0
Pitch bend does not smoothly exit idle position
#201
scottc11
closed
1 year ago
0
when exiting FREEZE, update the display based on the sequence progress
#200
scottc11
closed
1 year ago
0
During record armed stage, listen for any touch events that occur 12 PPQN prior to enabling record and slot those at the position 0 of the sequence
#199
scottc11
closed
1 year ago
0
Touch over-ride snapback
#198
scottc11
closed
1 year ago
0
Stopping and launching a sequence (like in ableton)
#197
scottc11
opened
2 years ago
0
Tap Tempo
#196
scottc11
opened
2 years ago
0
Add a version key to the start of the settings Flash storage location
#195
scottc11
closed
1 year ago
0
Hardware 4-stage toggle switch for setting 3/4, 4/4, 5/4 and 7/4
#194
scottc11
opened
2 years ago
0
Bender recording in Pitch Bend mode doesn't playback what you perform (while recording)
#193
scottc11
closed
1 year ago
1
What happens when you have an active sequence running, and then switch into quantizer mode?
#192
scottc11
closed
1 year ago
0
Firmware Update Dec 2022
#191
scottc11
closed
1 year ago
0
Determine sequence length by using a "time signature" parameter, so that a sequence only starts recording on beat 1 of that bar, and ends recording on the last beat of that bar
#190
scottc11
closed
1 year ago
0
Allow sequencing the octaves touch pads
#189
scottc11
closed
1 year ago
0
After recording a sequence, if you apply any ratcheting the recorded gate signals stop triggering
#188
scottc11
closed
1 year ago
0
ADC reads when at 0v / GND freeze the system
#187
scottc11
closed
1 year ago
1
Quantization on record
#186
scottc11
opened
2 years ago
0
Gesture to save all active sequences between power cycles
#185
scottc11
closed
1 year ago
0
Layer Stackup guidlines
#184
scottc11
opened
2 years ago
0
Transposition of all 4 channels
#183
scottc11
opened
2 years ago
0
If you use a really low frequency LFO, the quantizer will not latch to any new notes
#182
scottc11
closed
1 year ago
0
Switch and Jack nuts become loose during shipping, secure with Split Washers?
#181
scottc11
opened
2 years ago
0
Active Degree Limit
#180
scottc11
opened
2 years ago
0
Allow CLEAR to work for all currently touched channel select pads
#179
scottc11
closed
2 years ago
0
If a channel is in quantizer mode, the display LEDs do not illuminate when you press record
#178
scottc11
closed
2 years ago
0
Bender sequence doesn't play back when in quantizer mode
#177
scottc11
closed
2 years ago
1
just fucking launch
#176
scottc11
closed
2 years ago
0
Power MCU via USB when not connected to 12V supply
#174
scottc11
opened
2 years ago
1
AVDD pin needs a ferrite bead between 3v3 supply
#173
scottc11
closed
1 year ago
1
Bender sequencing (at least pitch bend) does not playback in seq length mode
#172
scottc11
closed
2 years ago
0
Try disabling the seq clock when entering VCOI calibration
#171
scottc11
opened
2 years ago
0
In quantizer mode, make the active degrees and octaves much dimmer then the current degree and octave
#170
scottc11
closed
2 years ago
0
Clearing a sequence while record enabled is buggy
#169
scottc11
closed
2 years ago
1
What are you going to do with the SX1509 clock jumper?
#168
scottc11
opened
2 years ago
0
make the TH Pads on the power header bigger / wider (drill stays the same, diameter / exposed copper increases)
#167
scottc11
closed
1 year ago
1
Flash / Blink the current step in the display at the same rate of Tempo LED
#166
scottc11
opened
2 years ago
0
Copy Paste a channels sequence length by pressing entering Seq Length menu, holding target channel and destination channel
#165
scottc11
opened
2 years ago
0
Disable console logging for production
#164
scottc11
closed
2 years ago
0
Rework Bender Calibration display gesture
#163
scottc11
opened
2 years ago
1
VCO Tuner does not recieve values on the queue if no signal is plugged into the CV input jack 🤷♂️
#162
scottc11
opened
2 years ago
1
Next