Uses a RF433Mhz component plugged on an Arduino to listen to known signals and decode it.
Download a zip of this repository, then include it from the Arduino IDE.
Arduino board. Tested with NANO and UNO.
Radio Frequence 433Mhz RECEIVER like MX-RM-5V.
RF433 RECEIVER data pin must be plugged on a board' digital PIN that can trigger interrupts.
On an UNO or NANO, this means D2 or D3.
Other boards will have different constraints. For example on ESP32, all GPIO pins can be configured as interrupts.
To see how to call library, you'll find an example here:
examples/01_generic/01_generic.ino
The function register_Receiver takes signal characteristics (encoding type,
signal timings) to do its job. How to work it out?
The painful way is to record signal, using for example a low level signal recording like gnuradio or a Radio Frequencies sniffing library/code like https://github.com/sebmillet/rf433snif (There are many others.) Then, to deduct signal timings. Good luck!
An easier way is to use RF433any library, found here:
https://github.com/sebmillet/RF433any
and to execute the code 01_main.ino found in the folder examples/01_main
Ultimately the code is the below one:
https://github.com/sebmillet/RF433any/blob/main/examples/01_main/01_main.ino
This code will output what register_Receiver needs to be called with, so as
to decode the signal received.
For example, if 01_main.ino outputs the below:
Waiting for signal
Data: 8a 34 e6 bf
-----CODE START-----
// [WRITE THE DEVICE NAME HERE]
rf.register_Receiver(
RFMOD_TRIBIT, // mod
7056, // initseq
0, // lo_prefix
0, // hi_prefix
0, // first_lo_ign
580, // lo_short
1274, // lo_long
0, // hi_short (0 => take lo_short)
0, // hi_long (0 => take lo_long)
520, // lo_last
7056, // sep
32 // nb_bits
);
-----CODE END-----Then you can manage reception like this:
#include "RF433recv.h"
#include <Arduino.h>
// Depends on your schematic - here, the Radio Frequencies device is
// plugged on Arduino' D2.
#define PIN_RFINPUT 2
RF_manager rf(PIN_RFINPUT);
void callback1(const BitVector *recorded) {
Serial.print(F("Signal received from telecommand\n"));
}
void callback2(const BitVector *recorded) {
Serial.print(F("Signal received from telecommand, code = 8A34E6BF\n"));
}
void setup() {
pinMode(PIN_RFINPUT, INPUT);
Serial.begin(115200);
// [OTIO (no rolling code, 32-bit)]
rf.register_Receiver(
RFMOD_TRIBIT, // mod
4956, // initseq
0, // lo_prefix
0, // hi_prefix
0, // first_lo_ign
580, // lo_short
1274, // lo_long
0, // hi_short (0 => take lo_short)
0, // hi_long (0 => take lo_long)
520, // lo_last
4956, // sep
32, // nb_bits
callback1,
2000
);
rf.register_callback(callback2, 2000,
new BitVector(32, 4, 0x8A, 0x34, 0xE6, 0xBF));
Serial.print(F("Waiting for signal\n"));
rf.activate_interrupts_handler();
}
void loop() {
rf.do_events();
}You can call register_callback without specifying the code, too. The code above is equivalent to the below (only showing what changes):
// ...
// [OTIO (no rolling code, 32-bit)]
rf.register_Receiver(
RFMOD_TRIBIT, // mod
4956, // initseq
0, // lo_prefix
0, // hi_prefix
0, // first_lo_ign
580, // lo_short
1274, // lo_long
0, // hi_short (0 => take lo_short)
0, // hi_long (0 => take lo_long)
520, // lo_last
4956, // sep
32 // nb_bits
);
rf.register_callback(callback1, 2000);
rf.register_callback(callback2, 2000,
new BitVector(32, 4, 0x8A, 0x34, 0xE6, 0xBF));
// ...The value 2000 is the minimum the delay in milliseconds between two calls, so here it makes 2000 milliseconds = 2 seconds.
RSwitch library is available in Arduino library manager. It is also available on github, here: https://github.com/sui77/rc-switch/
The example examples/04_rcswitch_recv/04_rcswitch_recv.ino shows how to decode RCSwitch protocols.
This has a performance impact that was measured, see file README-PROGMEM.md.
You can register as many decoders as you wish (calling register_Receiver). But since the decoding takes place in the interrupt handler, if too many decoders are registered, at some point the signals with short typical durations won't work.
This is because RF433recv decodes on the fly, inside the interrupt handler.
The library as of version 0.1.5, contains a small buffer (4 bytes) to help analyze the signal on the fly. This gives flexibility when decoding signals and allows to register more decoders. Until version 0.1.4, not all RCSwitch protocols could be decoded at the same time (you could have up to 8).
Now you can simply register all RCSwitch protocols and it'll work fine, so all in all, RF433recv allows to register 12 decoders in parallel and have all of them work successfully. Even RCSwitch protocl 7! (that has a short signal duration of 150 microseconds = very low).
Ultimately the author warns against registering too many decoders at the same time, but can claim the 12 RCSwitch protocols work happily when all of them are registered in parallel.
See examples/04_rcswitch_recv/04_rcswitch_recv.ino to see how the 12 registrations are done.