issues
search
sinara-hw
/
Stabilizer
2-channel microcontroller servo with EEM and Ethernet based on STM32 CPU
Other
21
stars
5
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Trouble Building Firmware and Extracting Application
#121
kvziegler
closed
3 months ago
6
Flashing Stabilizer
#120
kvziegler
closed
3 months ago
3
v1.3.2 DAC8831IBD noise
#119
MorganTL
opened
3 months ago
4
7A-8.000MAAE-T is obsolete
#118
MorganTL
opened
5 months ago
2
obsolete USB connector
#117
gkasprow
opened
5 months ago
0
default to rear MRX56904CV molex and DNP rear barrel
#116
jordens
opened
11 months ago
0
Move JTAG/SWD connector to the back
#115
jordens
opened
11 months ago
0
wrong panel PN
#114
gkasprow
opened
1 year ago
0
v1.3.4 changelog
#113
maciejprzybysz
opened
1 year ago
7
Obsolete microUSB connector
#112
filipswit
closed
1 year ago
1
v1.3.3 changelog
#111
filipswit
opened
1 year ago
0
Fragile thermals of backside barrel connector
#110
pmldrmota
closed
1 year ago
0
Header I2C bus should have pull-up resistors
#109
nkrackow
opened
2 years ago
2
parts availability
#108
gkasprow
closed
1 year ago
0
v1.3.2 DAC8831IBD glitch
#107
jordens
opened
2 years ago
1
v.1.3.2 changelog
#106
gkasprow
opened
2 years ago
0
v1.3.1 Changelog
#105
maciejprzybysz
opened
2 years ago
0
Some VIAs are not tented
#104
maciejprzybysz
closed
2 years ago
0
Top overlay covers SMD pads
#103
maciejprzybysz
closed
2 years ago
1
On Mechanical1 (board outline) there are 3D models and unwanted free line
#102
maciejprzybysz
closed
2 years ago
0
USB ID line not connected to ESD diode
#101
maciejprzybysz
closed
2 years ago
0
Project validation causes errors
#100
maciejprzybysz
closed
2 years ago
0
ETH series resistors - same designators
#99
maciejprzybysz
closed
2 years ago
0
pull ups on DAC LDAC and CLR
#98
jordens
closed
1 year ago
22
v1.3 changelog
#97
gkasprow
opened
3 years ago
0
Frontpanel cut-outs/silkscreen for standalone enclosure
#96
nkrackow
closed
1 year ago
7
BOM issue 3.3pF
#95
gkasprow
closed
3 years ago
1
SMA/MCX connector pins are too long
#94
nkrackow
closed
3 years ago
10
LT3042 fast start was added in v1.2?
#93
dnadlinger
closed
3 years ago
1
PHY_T/RD_P/N series resistance
#92
jordens
closed
3 years ago
1
DI0/1 jitter, pulldown
#91
jordens
closed
3 years ago
5
DI0/1 input protection
#90
jordens
closed
3 years ago
2
wrong REV ID
#89
gkasprow
closed
3 years ago
6
JTAG connector is EOL
#88
gkasprow
closed
3 years ago
1
P12VA LED occasionally does not illuminate
#87
ryan-summers
closed
3 years ago
9
digital outputs
#86
jbqubit
closed
3 years ago
4
MFG issues
#85
gkasprow
closed
3 years ago
0
PHY NRST pull-down
#84
jordens
closed
3 years ago
1
DAC updates may cause transient spikes at specific code boundaries
#83
ryan-summers
closed
3 years ago
6
P5V0A rail continuity
#82
jordens
closed
4 years ago
1
test v1.2 Stabilizer with Netgear GS305P PoE ethernet switch
#81
gkasprow
opened
4 years ago
0
[v1.1 hw] JTAG TDI is shared with SPI3_NSS
#80
jordens
closed
4 years ago
0
v1.2 changelog
#79
gkasprow
closed
3 years ago
1
Clean up PA0 for timing input from Pounder
#78
jordens
closed
4 years ago
1
quadspi read contention
#77
jordens
closed
4 years ago
2
[Stabilizer v1.1] Ethernet auto-negotiation fails with PoE switch
#76
ryan-summers
closed
4 years ago
7
v1.1 bad power connection
#75
jordens
closed
4 years ago
2
[Stabilizer v1.1] Configuring RMII interface pins causes a CPU reset
#74
ryan-summers
closed
4 years ago
18
[Stabilizer v1.1] EEM I2C signals held low
#73
ryan-summers
closed
4 years ago
8
PoE vs. EEM power conflict
#72
sbourdeauducq
closed
4 years ago
10
Next