search

yrzr / opnsense-tools

OPNsense images native builder for aarch64. Steps to build your own image: https://yrzr.github.io/tutorial-build-opnsense-arm64-on-a-rpi4/
https://yrzr.github.io/tags/opnsense/
BSD 2-Clause "Simplified" License
40 stars 1 forks source link

Boot from Sata #4

Closed ChrisS1985ET closed 2 months ago

ChrisS1985ET commented 10 months ago

Please help, I am trying to boot your image on rpi4, have been successful booting from sdcard 'mmc' but i would like to have my u-boot boot from may sata 'scsi' connection, my attempts have not been well. I know the Sata disk is visible from the console. Any advice? Output below. thanks.

U-Boot 2022.04-armbian (May 16 2022 - 17:50:52 +0000)

DRAM: 1 GiB Core: 38 devices, 20 uclasses, devicetree: fit WDT: Not starting watchdog@8300 Comphy chip #0: Comphy-0: USB3_HOST0 5 Gbps Comphy-1: PEX0 5 Gbps Comphy-2: SATA0 6 Gbps Target spinup took 0 ms. AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: ncq led only pmp fbss pio slum part sxs PCIe: Link down MMC: sdhci@d0000: 0, sdhci@d8000: 1 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 By tes, erase size 4 KiB, total 4 MiB OK Model: Net: eth0: ethernet@30000 Hit any key to stop autoboot: 0 MMC: no card present Couldn't find partition mmc 0:1 Can't set block device MMC: no card present Couldn't find partition mmc 0:1 Can't set block device MMC: no card present Scanning disk sdhci@d0000.blk... Disk sdhci@d0000.blk not ready Found 0 disks No EFI system partition ERROR: invalid device tree => env default -a

Resetting to default environment

=> setenv bootcmd 'scsi scan; scsi dev 0; ext4load scsi 0:0 $fdt_addr dtb/marvell/armada-3720-espressobin.dtb; ext4load scsi 0:0 $kernel_addr EFI/BOOT/bootaa64.efi; bootefi $kernel_addr $fdt_addr' => env save Saving Environment to SPIFlash... Erasing SPI flash...Writing to SPI flash...done OK => boot scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: SanDisk SD6SB1M1 Rev: X231 Type: Hard Disk Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)

Device 0: (0:0) Vendor: ATA Prod.: SanDisk SD6SB1M1 Rev: X231 Type: Hard Disk Capacity: 122104.3 MB = 119.2 GB (250069680 x 512) ... is now current device Can't set block device Can't set block device ERROR: invalid device tree =>

ChrisS1985ET commented 10 months ago

All good, I've sorted it, booting opnsense on sata but now I am getting a mount error 19 and nothings shows up as listed under geom disk listing. Any ideas?

yrzr commented 7 months ago

I see you are using u-boot built by armbian. I haven't tried it. But I can boot my 4GB RAM RPI4 from my SSD drive through usb3 bridge.

Both u-boot and the FreeBSD 13.2 kernel can recognize my SSD drive and find the right partition. Please see your boot fails on which step.

U-Boot 2023.01 (Jul 03 2023 - 08:43:37 +0000)

DRAM:  947 MiB (effective 3.9 GiB)
RPI 4 Model B (0xc03111)
Core:  203 devices, 16 uclasses, devicetree: board
MMC:   mmc@7e300000: 3, emmc2@7e340000: 0
Loading Environment from FAT... ** Bad device specification mmc 1 **
In:    serial
Out:   vidconsole
Err:   vidconsole
Net:   eth0: ethernet@7d580000
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
Bus xhci_pci: Register 5000420 NbrPorts 5
Starting the controller
USB XHCI 1.00
scanning bus xhci_pci for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
MMC Device 1 not found
no mmc device at slot 1
MMC Device 2 not found
no mmc device at slot 2

Device 0: Vendor: GLOWAY Y Rev: F30A Prod: CT120GS3-S7
            Type: Hard Disk
            Capacity: 114473.4 MB = 111.7 GB (234441648 x 512)
... is now current device
Scanning usb 0:1...
                                                                                                                                    ^Card did not respond to voltage select! : -110
No EFI system partition
BootOrder not defined
EFI boot manager: Cannot load any image
Found EFI removable media binary efi/boot/bootaa64.efi
1174172 bytes read in 5 ms (224 MiB/s)
Booting /efi\boot\bootaa64.efi
console comconsole failed to initialize
Consoles: EFI console
    Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/arm64 EFI loader, Revision 1.1

   Command line arguments: loader.efi
   Image base: 0x39aff000
   EFI version: 2.100
   EFI Firmware: Das U-Boot (rev 8227.256)
   Console: efi,comconsole (0)
   Load Path: /efi\boot\bootaa64.efi
   Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x3)/UsbClass(0x2109,0x715,0x0,0x0,0x0)/HD(1,0x01,0,0x800,0x19000)
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x3)/UsbClass(0x2109,0x715,0x0,0x0,0x0)/HD(1,0x01,0,0x800,0x19000)
Setting currdev to disk0p1:
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x3)/UsbClass(0x2109,0x715,0x0,0x0,0x0)/HD(2,0x01,0,0x19800,0x5e6800)
Setting currdev to disk0p2:
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.local
c\
|
             ______  _____  _____
            /  __  |/ ___ |/ __  |
            | |  | | |__/ | |  | |___  ___ _ __  ___  ___
            | |  | |  ___/| |  | / __|/ _ \ '_ \/ __|/ _ \
            | |__| | |    | |  | \__ \  __/ | | \__ \  __/
            |_____/|_|    |_| /__|___/\___|_| |_|___/\___|

 +-----------------------------------------+     @@@@@@@@@@@@@@@@@@@@@@@@@@@@
 |                                         |   @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
 |  1. Boot Multi user [Enter]             |   @@@@@                    @@@@@
 |  2. Boot Single user                    |       @@@@@            @@@@@
 |  3. Escape to loader prompt             |    @@@@@@@@@@@       @@@@@@@@@@@
 |  4. Reboot                              |         \\\\\         /////
 |  5. Cons: Serial                        |   ))))))))))))       (((((((((((
 |                                         |         /////         \\\\\
 |  Options:                               |    @@@@@@@@@@@       @@@@@@@@@@@
 |  6. Kernel: default/kernel (1 of 1)     |       @@@@@            @@@@@
 |  7. Boot Options                        |   @@@@@                    @@@@@
 |                                         |   @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
 |                                         |   @@@@@@@@@@@@@@@@@@@@@@@@@@@@
 +-----------------------------------------+
   Autoboot in 0 seconds. [Space] to pause     23.7  ``Restless Roadrunner'' -

Loading kernel...
/boot/kernel/kernel text=0x2a8 text=0x9421e0 text=0x236cec data=0x1ba438 data=0x0+0x2b2000 0x8+0x13bae0+0x8+0x161cae\
Loading configured modules...
/boot/kernel/pfsync.ko text=0x2f63 text=0x7fcc data=0xb38+0x8 0x8+0x1830+0x8+0x1192
loading required module 'pf'
/boot/kernel/pf.ko text=0xed00 text=0x3d060 data=0x5a40+0x3fc 0x8+0x5ca0+0x8+0x4b21
/etc/hostid size=0x25
/boot/kernel/if_enc.ko text=0x15ca text=0x934 data=0x750 0x8+0xca8+0x8+0xb71
/boot/kernel/pflog.ko text=0xf78 text=0x888 data=0x430 0x8+0x9f0+0x8+0x712
/boot/kernel/if_gre.ko text=0x2736 text=0x40f8 data=0x8c8+0x40 0x8+0x1728+0x8+0xfd5
/boot/kernel/carp.ko text=0x3500 text=0x6f80 data=0xcd0+0x48 0x8+0x1a28+0x8+0x12ef
/boot/entropy size=0x1000
/boot/kernel/if_bridge.ko text=0x3884 text=0x6e2c data=0xde8+0x8 0x8+0x1c98+0x8+0x16b2
loading required module 'bridgestp'
/boot/kernel/bridgestp.ko text=0x12e5 text=0x4cd8 data=0x2c8+0x28 0x8+0xb40+0x8+0x6b4
/boot/kernel/if_lagg.ko text=0x3d0f text=0x9890 data=0xd10+0x8 0x8+0x1c80+0x8+0x15a3
loading required module 'if_infiniband'
/boot/kernel/if_infiniband.ko text=0x1102 text=0x112c data=0x300+0x8 0x8+0x8d0+0x8+0x59a
Using DTB provided by EFI at 0x7ef0000.
EFI framebuffer information:
addr, size     0x3e9be000, 0x103000
dimensions     592 x 448
stride         592
masks          0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.2-RELEASE-p3 stable/23.7-n254799-01e2d59d337 SMP arm64
FreeBSD clang version 14.0.5 (https://github.com/llvm/llvm-project.git llvmorg-14.0.5-0-gc12386ae247c)
VT(efifb): resolution 592x448
module firmware already present!
real memory  = 4147109888 (3954 MB)
avail memory = 4018868224 (3832 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
MAP 39c26000 mode 2 pages 1
MAP 39c2a000 mode 2 pages 1
MAP 39c2c000 mode 2 pages 2
MAP 39c2f000 mode 2 pages 4
MAP 3b040000 mode 2 pages 16
MAP fe100000 mode 0 pages 1
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
clk_fixed1: <Fixed clock> on ofw_clkbus0
clk_fixed2: <Fixed clock> on ofwbus0
clk_fixed3: <Fixed clock> on ofwbus0
simplebus1: <Flattened device tree simple bus> on ofwbus0
simplebus2: <Flattened device tree simple bus> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
simplebus3: <Flattened device tree simple bus> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0
bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
gpiobus1: <GPIO bus> on gpio1
regfix0: Cannot set GPIO pin: 6
REGNODE_INIT failed: 6
regfix0: Cannot register regulator.
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0
gpioregulator0: <GPIO controlled regulator> on ofwbus0
generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on simplebus0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0
uart0: console (115200,n,8,1)
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 31,32,33,34,35,36,37,38,39,40,41 on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on simplebus0
bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on simplebus0
gpioc1: <GPIO controller> on gpio1
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 73 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fb0: keeping existing fb bpp of 32
fbd0 on fb0
WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 14.0.
VT: Replacing driver "efifb" with new "fb".
fb0: 592x448(592x448@0,0) 32bpp
fb0: fbswap: 1, pitch 2368, base 0x3e9be000, screen_size 1060864
sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff irq 79 on simplebus1
mmc1: <MMC/SD bus> on sdhci_bcm1
pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
pcib0: <BCM2838-compatible PCI-express controller> mem 0x7d500000-0x7d50930f irq 80,81 on simplebus2
pcib0: hardware identifies as revision 0x304.
pci1: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 91 at device 0.0 on pci1
pci2: <PCI bus> on pcib1
bcm_xhci0: <VL805 USB 3.0 controller (on the Raspberry Pi 4b)> irq 92 at device 0.0 on pci2
bcm_xhci0: 32 bytes context size, 64-bit DMA
usbus0 on bcm_xhci0
pci0: <PCI bus> on pcib0
pci0: failed to allocate bus number
device_attach: pci0 attach returned 6
genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 82,83 on simplebus2
genet0: GENET version 5.0 phy 0x0000
miibus0: <MII bus> on genet0
brgphy0: <BCM54213PE 1000BASE-T media interface> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
genet0: Ethernet address: dc:a6:32:06:6a:ef
gpioled0: <GPIO LEDs> on ofwbus0
armv8crypto0: CPU lacks AES instructions
Timecounters tick every 1.000 msec
usbus0: 5.0Gbps Super Speed USB v3.0
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
ugen0.1: <(0x1106) XHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <(0x1106) XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
mmc0: No compatible cards found on bus
mmc1: No compatible cards found on bus
bcm2835_cpufreq0: ARM 600MHz, Core 200MHz, SDRAM 400MHz, Turbo OFF
CPU  0: ARM Cortex-A72 r0p3 affinity:  0
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG>
 Instruction Set Attributes 0 = <CRC32>
 Instruction Set Attributes 1 = <>
 Instruction Set Attributes 2 = <>
         Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <>
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA>
      Memory Model Features 1 = <8bit VMID>
      Memory Model Features 2 = <32bit CCIDX,48bit VA>
             Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
             Debug Features 1 = <>
         Auxiliary Features 0 = <>
         Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU  1: ARM Cortex-A72 r0p3 affinity:  1
CPU  2: ARM Cortex-A72 r0p3 affinity:  2
CPU  3: ARM Cortex-A72 r0p3 affinity:  3
Release APs...done
uhub0: 5 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/ufs/OPNsense [rw]...
ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on usbus0
Root mount waiting for: usbus0
uhub1: 4 ports with 4 removable, self powered
Root mount waiting for: usbus0
usb_msc_auto_quirk: UQ_MSC_NO_GETMAXLUN set for USB mass storage device VLI Manufacture String VLI Product String (0x2109:0x0715)
ugen0.3: <VLI Manufacture String VLI Product String> at usbus0
umass0 on uhub0
umass0: <VLI Manufacture String VLI Product String, class 0/0, rev 3.10/1.31, addr 2> on usbus0
umass0:  SCSI over Bulk-Only; quirks = 0x0100
umass0:0:0: Attached to scbus0
(probe0:umass-sim0:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command operation code)
(probe0:umass-sim0:0:0:0): Error 22, Unretryable error
da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
da0: <GLOWAY Y CT120GS3-S7 F30A> Fixed Direct Access SPC-4 SCSI device
da0: Serial Number 000000123ADA
da0: 400.000MB/s transfers
da0: 114473MB (234441648 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
WARNING: /: TRIM flag on fs but disk does not support TRIM
Warning: no time-of-day clock registered, system time will not be set accurately
Mounting filesystems...
tunefs: soft updates remains unchanged as enabled
tunefs: issue TRIM to the disk remains unchanged as enabled
** /dev/ufs/OPNsense
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 368342 free (646 frags, 45962 blocks, 0.1% fragmentation)
Setting hostuuid: 30303031-3030-3030-6134-386137303365.
Setting hostid: 0xa01eb9a4.
Configuring vt: blanktime.
Setting up /var/log memory disk...done.
Configuring crash dump device: /dev/null
.ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg /usr/local/lib/ipsec /usr/local/lib/perl5/5.34/mach/CORE
done.
>>> Invoking early script 'upgrade'
>>> Invoking early script 'configd'
Starting configd.
>>> Invoking early script 'templates'
Generating configuration: OK
>>> Invoking early script 'backup'
>>> Invoking backup script 'captiveportal'
>>> Invoking backup script 'dhcpleases'
>>> Invoking backup script 'duid'
>>> Invoking backup script 'netflow'
>>> Invoking backup script 'rrd'
>>> Invoking early script 'carp'
CARP event system: OK
Launching the init system...done.
Initializing...........done.
genet0: link state changed to UP
Starting device manager...done.
Configuring login behaviour...done.
Configuring loopback interface...lo0: link state changed to UP
done.
Configuring kernel modules...done.
Setting up extended sysctls...done.
Setting timezone: Etc/UTC
Writing firmware setting...done.
Writing trust files...done.
Setting hostname: OPNsense.localdomain
Generating /etc/resolv.conf...done.
Generating /etc/hosts...done.
Configuring system logging...done.
Configuring firewall.......done.
Configuring hardware interfaces...done.
Configuring loopback interface...done.
Configuring LAGG interfaces...done.
Configuring VLAN interfaces...done.
Configuring WAN interface...done.
Generating /etc/resolv.conf...done.
Generating /etc/hosts...done.
Configuring firewall.......done.
Starting web GUI...done.
Setting up routes...done.
Starting Unbound DNS...done.
Configuring firewall.......done.
Setting up gateway monitors...done.
Syncing OpenVPN settings...done.
Starting NTP service...done.
Starting Unbound DNS...done.
Generating RRD graphs...done.
>>> Invoking start script 'newwanip'
Reconfiguring IPv4 on genet0
Reconfiguring IPv6 on genet0
>>> Invoking start script 'freebsd'
Starting powerd.
>>> Invoking start script 'syslog'
>>> Invoking start script 'carp'
>>> Invoking start script 'cron'
Starting Cron: OK
>>> Invoking start script 'openvpn'
>>> Invoking start script 'sysctl'
Service `sysctl' has been restarted.
>>> Invoking start script 'beep'
>>> Error in start script '95-beep'
Root file system: /dev/ufs/OPNsense
Tue Nov 14 04:40:33 UTC 2023