Closed GoogleCodeExporter closed 9 years ago
Which version of the GCS are you using? 8 or 9?
8 is for MAVLink 0.9,
9 is for MAVLink 1.0
Original comment by Bart.Ver...@gmail.com
on 4 Apr 2012 at 3:07
[deleted comment]
I have version 8 and arducopter 2.0.49 and it worked perfekt.
Since I update to 2.5.3 I testet with 8, but the mavlink symbole was
deaktivated,
I update to 9 and it was aktiv, and it says there is a link, but if I klick on
any botton nothing is shown.
Changed Bautrate in Arducopter compiling same as in module.
I use 115200
thx
druckgott
Original comment by druckgott
on 6 Apr 2012 at 8:43
Just saw your message. Does the system work without copter-gcs?
I can try to install 2.5.3 on mine, but its APM 1280. I will try to get to it
this week, but real-life is pretty hectic atm. The baud-rate doesn't affect
copter-gcs.
When you say version 8 had "mavlink symbol" disabled, what do you mean? It
should always be available.
Original comment by Orio...@gmail.com
on 9 Apr 2012 at 1:58
I just played around with the code. Could you try reloading version 8? It
really should be working...
Original comment by Orio...@gmail.com
on 12 Apr 2012 at 12:30
mhh on my Computer it also do not work, the light of the bluetooth modul is
always going on for some seconds and than it´s blinking again.
In version 8, it was dissabled and I can´t click the mavelink symbol.
I will take a look that I Upload an old firmware to my copter this week and
then try it again and will write you bag.
thx
druckgott
Original comment by druckgott
on 15 Apr 2012 at 9:30
ok now I can get it I always thinked that I have 115200bits and not 57600
I have changed it a time ago, because I don´t want to change the config of
arducopter.
In Version 8 it works perfekt now, but version 9 don´t work for me
Original comment by druckgott
on 17 Apr 2012 at 6:50
Ok I check it with version 2.5.3 don´t work.
then 2.5.4 not it works and baut 57600.
But only Version 8, on 9 I do get a connection, but no heartbeat, what could
be the problem?
Original comment by druckgott
on 22 Apr 2012 at 8:19
Version 8 is for MAVLink .9, Version 9 is for MAVLink 1.0
Only one of these will work, and I expect that version is 8.
The connection just means you have a bluetooth link (hardware only). The
heartbeat is MAVLink is working.
Can you confirm that version 8 works for 2.5.4? Thanks
Original comment by Orio...@gmail.com
on 22 Apr 2012 at 3:22
I can verify that version 8 works with 2.5.3 but not version 9. I haven't
uploaded 2.5.4 yet but will check this soon. Thanks for the awesome work!
Rob
Original comment by rv8...@gmail.com
on 24 Apr 2012 at 12:56
Got it! So apparently version 2.6 will support MAVLink 1.0
http://diydrones.com/forum/topics/arducopter-v2-5-3-mavlink-version?commentId=70
5844%3AComment%3A842303&xg_source=activity
Thanks again!
Rob
Original comment by rv8...@gmail.com
on 24 Apr 2012 at 1:11
Excellent, good to know. Thanks!
Now just need to figure out supporting both...
Original comment by Orio...@gmail.com
on 24 Apr 2012 at 1:15
Original issue reported on code.google.com by
druckgott
on 4 Apr 2012 at 3:04