Donderda
commented
5 years ago My User_config.h:
/*
OpenMQTTGateway - ESP8266 or Arduino program for home automation
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
Send and receiving command by MQTT
This program enables to:
- receive MQTT data from a topic and send RF 433Mhz signal corresponding to the received MQTT data
- publish MQTT data to a different topic related to received 433Mhz signal
- receive MQTT data from a topic and send IR signal corresponding to the received MQTT data
- publish MQTT data to a different topic related to received IR signal
- publish MQTT data to a different topic related to BLE devices rssi signal
Copyright: (c)Florian ROBERT
This file is part of OpenMQTTGateway.
OpenMQTTGateway is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
OpenMQTTGateway is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*-------------------VERSION----------------------*/
#define OMG_VERSION "0.8"
/*-------------DEFINE YOUR MQTT PARAMETERS BELOW----------------*/
//MQTT Parameters definition
//#define mqtt_server_name "www.mqtt_broker.com" // instead of defining the server by its IP you can define it by its name, uncomment this line and set the correct MQTT server host name
char mqtt_user[20] = "your_username"; // not compulsory only if your broker needs authentication
char mqtt_pass[20] = "your_password"; // not compulsory only if your broker needs authentication
char mqtt_server[40] = "192.168.1.17";
char mqtt_port[6] = "1883";
#define Gateway_Name "OpenMQTTGateway"
#define Base_Topic "home/"
#define version_Topic Base_Topic Gateway_Name "/version"
#define will_Topic Base_Topic Gateway_Name "/LWT"
#define will_QoS 0
#define will_Retain true
#define will_Message "Offline"
#define Gateway_AnnouncementMsg "Online"
/*-------------DEFINE YOUR NETWORK PARAMETERS BELOW----------------*/
//#define ESPWifiManualSetup true //uncomment you don't want to use wifimanager for your credential settings on ESP
#define WifiManager_password "your_password"
//#define MDNS_SD //uncomment if you want to use mdns for discovering automatically your ip server, please note that MDNS with ESP32 can cause the BLE to not work
//#define cleanFS true //uncomment if you want to clean the ESP memory and reenter your credentials
#define maxMQTTretry 4 //maximum MQTT connection attempts before going to wifi setup
//set minimum quality of signal so it ignores AP's under that quality
#define MinimumWifiSignalQuality 8
// Update these with values suitable for your network.
#if defined(ESP32) || defined(ESPWifiManualSetup) // for nodemcu, weemos and esp8266
#define wifi_ssid "wifi ssid"
#define wifi_password "wifi password"
#else // for arduino + W5100
const byte mac[] = { 0xDE, 0xED, 0xBA, 0xFE, 0x54, 0x95 }; //W5100 ethernet shield mac adress
#endif
const byte ip[] = { 192, 168, 1, 99 }; //ip adress
const byte gateway[] = { 0, 0, 0, 0 }; //ip adress, if first value is different from 0 advanced config network will be used and you should fill gateway & dns
const byte Dns[] = { 0, 0, 0, 0 }; //ip adress, if first value is different from 0 advanced config network will be used and you should fill gateway & dns
const byte subnet[] = { 255, 255, 255, 0 }; //ip adress
/*-------------DEFINE YOUR OTA PARAMETERS BELOW----------------*/
#define ota_hostname Gateway_Name
#define ota_password "OTAPASSWORD"
#define ota_port 8266
/*-------------DEFINE PINs FOR STATUS LEDs----------------*/
#define led_receive 40
#define led_send 42
#define led_error 44
// VCC ------------D|-----------/\/\/\/\ ----------------- Arduino PIN
// LED Resistor 270-510R
/*-------------DEFINE THE MODULES YOU WANT BELOW----------------*/
//Addons and module management, comment the Z line
//#define ZgatewayRF "RF" //ESP8266, Arduino, ESP32
//#define ZgatewayRF315 "RF315" //ESP8266, Arduino, ESP32
//#define ZgatewayIR "IR" //ESP8266, Arduino, Sonoff RF Bridge
//#define ZgatewayIR
// #include "config_IR.h"
//#define ZgatewayBT "BT" //ESP8266, Arduino, ESP32
//#define ZgatewayRF2 "RF2" //ESP8266, Arduino, ESP32
//#define ZgatewaySRFB "SRFB" // Sonoff RF Bridge
// #include "config_SRFB.h"
//#define Zgateway2G "2G" //ESP8266, Arduino, ESP32
//#define ZactuatorONOFF "ONOFF" //ESP8266, Arduino, ESP32, Sonoff RF Bridge
//#define ZsensorINA226 "INA226" //ESP8266, Arduino, ESP32
//#define ZsensorHCSR501 "HCSR501" //ESP8266, Arduino, ESP32, Sonoff RF Bridge
//#define ZsensorADC "ADC" //ESP8266, Arduino, ESP32
//#define ZsensorBH1750 "BH1750" //ESP8266, Arduino, ESP32
//#define ZsensorTSL2561 "TSL2561" //ESP8266, Arduino, ESP32
//#define ZsensorBME280 "BME280" //ESP8266, Arduino, ESP32
//#define ZsensorDHT "DHT" //ESP8266, Arduino, ESP32, Sonoff RF Bridge
//#define ZgatewayRFM69 "RFM69" //ESP8266, Arduino, ESP32
//#define ZgatewayRF
//#include "config_RF.h"
//#define ZgatewayRF2
#define ZgatewaySRFB
#include "config_SRFB.h"
#define ZgatewayIR
#include "config_IR.h"
//#define ZgatewayBT
//#include "config_BT.h"
//#define ZsensorINA226
/*----------------------------OTHER PARAMETERS-----------------------------*/
/*-------------------CHANGING THEM IS NOT COMPULSORY-----------------------*/
/*----------------------------USER PARAMETERS-----------------------------*/
#ifdef ZgatewaySRFB
#define SERIAL_BAUD 19200
#else
#define SERIAL_BAUD 115200
#endif
/*--------------MQTT general topics-----------------*/
// global MQTT subject listened by the gateway to execute commands (send RF, IR or others)
#define subjectMQTTtoX Base_Topic Gateway_Name "/commands/#"
#define subjectMultiGTWKey "toMQTT"
//variables to avoid duplicates
#define time_avoid_duplicate 3000 // if you want to avoid duplicate mqtt message received set this to > 0, the value is the time in milliseconds during which we don't publish duplicates
//uncomment to use multicore function of ESP32 for BLE
#ifdef ESP32
#define multiCore //comment to don't use multicore function of ESP32 for BLE
#endif
#define TimeBetweenReadingSYS 120000 // time between system readings (like memory)
#define subjectSYStoMQTT Base_Topic Gateway_Name "/SYStoMQTT"
/*-------------------ACTIVATE TRACES----------------------*/
#define TRACE 1 // 0= trace off 1 = trace on
Describe the bug I'm trying to flash my Sonoff RF-Bridge with OpenMQTTGateway. I enabled the IR Features following this page: https://1technophile.blogspot.com/2018/02/adding-infrared-emitter-to-sonoff-rf.html
When I try to compile the sourcecode, I get this error message:
Environment (please complete the following information):
lib-folder to my Arduino-lib folder.