-
### 您的功能请求是否与解决某些问题有关?请描述一下。/ Is your feature request related to a problem? Please describe.
希望能出一个用arduino写的air001的超低功耗模式的例程。
### 描述您想要的解决方案 / Describe the solution you'd like
希望能出一个用arduino写的air0…
-
Arduino boards manager link: https://github.com/Air-duino/Arduino-pack-json-ci/releases/download/Nightly/package_air_index.json
official site: https://wiki.luatos.com/chips/air001/index.html
wzwtt updated
11 months ago
-
如题,使用OpenOCD应该如何烧录程序近Air001呢,Openocd的.cfg文件应该怎么写呢
-
### 您的功能请求是否与解决某些问题有关?请描述一下。/ Is your feature request related to a problem? Please describe.
Air001增加Arduino增加产品唯一识别码功能chip
### 描述您想要的解决方案 / Describe the solution you'd like
Air001增加Arduino增加…
-
### 描述一下这个bug / Describe the bug
用eeprom.get读取只能读取128字节数据,用eeprom.put也是只能写入128字节数据,定义DATA_EEPROM_BASE和DATA_EEPROM_END也不能解决
### 复现步骤 / To Reproduce
#include
#include "Seeed_LDC1612.h"
#include
…
-
### 描述一下这个bug / Describe the bug
手里有一个ESP32和AIR001的板子,ESP32作主机,AIR001作为从机。ESP32用requestFrom方法,不能正常触发从机AIR001的onRequest注册的方法。但是两个ESP32分别作主机和从机,主机能够正常读取从机的数据。
### 复现步骤 / To Reproduce
从机先复位,然后主机复位,主机能…
-
### 描述一下这个bug / Describe the bug
两块板子,一块是ESP32C3,另一块是AIR001,用I2C连接,有接上拉电阻。ESP32C3作主机,AIR001作从机。ESP32C3主机用Wire.write方法发送操作多个字节的数据时,反馈结果是2,AIR001从机那边没有收到数据。之前 #34 这个bug有提过,但是没彻底解决。
### 复现步骤 / To R…
-
### 描述一下这个bug / Describe the bug
我想魔改HardwareSerial.cpp 以实现软件流控,发现函数_tx_complete_irq在返回0后,串口数据仍然没有传输完成,串口有波形输出
### 复现步骤 / To Reproduce
魔改HardwareSerial.cpp的部分内容如下:
```
int HardwareSerial::_tx_com…
-
### 描述一下这个bug / Describe the bug
项目中需要用到PB6的上拉输入状态,但是程序一直无法正常运行。后来发现是PB6的上拉输入状态有问题。
单独新建一个Arduino项目,3.3V供电,设置PB6为上拉输入状态,PB6在没有任何外部下拉的情况下用万用表测电压只有1.6V,处于不上不下的状态。
试过其他引脚都能在上拉输入状态维持接近3.3V的状态,包括设置PF4…
-
### 描述一下这个bug / Describe the bug
以下Arduino程序烧录后会导致刷写新程序异常困难,重复尝试十几次才能成功烧录一次。后来发现只要把舵机引脚PB6改为其他就可以正常刷写,说明程序对引脚的引用干扰了reset后boot模式的判断。如果无法修复的话建议直接禁用PB6作为输出功能使用,若使用则触发报错
### 复现步骤 / To Reproduce
···
#i…