GPRS/SMS Shield notable to control relay

GoogleCodeExporter commented 8 years ago

What steps will reproduce the problem?
1. i loaded the code and am not getting output
2. notable to see sms received or not through serial monitor

What is the expected output? What do you see instead?
expected output realy operation ;    am getting AT+CMGF=1

What version of the product are you using? On what operating system?

GPRS/GSM Shield v1.0 elcrow :     xp
Please provide any additional information below.

following is my code:

#include <SoftwareSerial.h>

// EN: String buffer for the GPRS shield message
String msg = String("");
// EN: Set to 1 when the next GPRS shield message will contains the SMS message
int SmsContentFlag = 0;
//control pins of relay.
int relay_a=4;
int relay_b=5;
int relay_c=6;
int relay_d=7;

// EN: Code PIN of the SIM card (if applied)
//String SIM_PIN_CODE = String( "XXXX" );

void setup()
{
  Serial.begin(9600);                 // the GPRS baud rate
  // Initialize  PINs
  pinMode( 4, OUTPUT ); 
  pinMode( 5, OUTPUT ); 
  pinMode( 6, OUTPUT ); 
  pinMode( 7, OUTPUT ); 
  digitalWrite( 4, LOW ); 
  digitalWrite( 5, LOW ); 
  digitalWrite( 6, LOW );
  digitalWrite( 7, LOW );
 Serial.println( "AT+CMGF=1" ); 
 delay(6000);
}

void loop()
{
    char SerialInByte;
    if(Serial.available())
    {       
        SerialInByte = (unsigned char)Serial.read();
       delay(5);

        // -------------------------------------------------------------------
        // EN: Program also listen to the GPRS shield message.
        // -------------------------------------------------------------------
       // EN: If the message ends with <CR> then process the message
        if( SerialInByte == 13 ){
          // EN: Store the char into the message buffer
          ProcessGprsMsg();
         }
         if( SerialInByte == 10 ){
            // EN: Skip Line feed
         }
         else {
           // EN: store the current character in the message string buffer
           msg += String(SerialInByte);
         }
     }   
}
// EN: Make action based on the content of the SMS. 
//     Notice than SMS content is the result of the processing of several GPRS 
shield messages.
void ProcessSms( String sms ){

  if( sms.indexOf("ona") >= 0 ){
    digitalWrite( relay_a, HIGH );
  }
   if( sms.indexOf("onb") >= 0 ){
    digitalWrite(  relay_b, HIGH );
  }
   if( sms.indexOf("onc") >= 0 ){
    digitalWrite(  relay_c, HIGH );
  }
  if( sms.indexOf("ond") >= 0 ){
    digitalWrite(  relay_d, HIGH );
  }
  if( sms.indexOf("offa") >= 0 ){
    digitalWrite(  relay_a, LOW );
  }
  if( sms.indexOf("offb") >= 0 ){
    digitalWrite(  relay_b, LOW );
  }
  if( sms.indexOf("offc") >= 0 ){
    digitalWrite(  relay_c, LOW );
  }
  if( sms.indexOf("offd") >= 0 ){
    digitalWrite(  relay_d, LOW );
  }
}
// EN: Request Text Mode for SMS messaging
void GprsTextModeSMS(){
  Serial.println( "AT+CMGF=1" );
}

void GprsReadSmsStore( String SmsStorePos ){
  Serial.print( "AT+CMGR=" );
  Serial.println( SmsStorePos );
}

// EN: Clear the GPRS shield message buffer
void ClearGprsMsg(){
  msg = "";
}

// EN: interpret the GPRS shield message and act appropiately
void ProcessGprsMsg() {
  if( msg.indexOf( "Call Ready" ) >= 0 ){
   //  Serial.println( "*** GPRS Shield registered on Mobile Network ***" );
     GprsTextModeSMS();
  }

  // EN: unsolicited message received when getting a SMS message
  if( msg.indexOf( "+CMTI" ) >= 0 ){
   //  Serial.println( "*** SMS Received ***" );
     // EN: Look for the coma in the full message (+CMTI: "SM",6)
     //     In the sample, the SMS is stored at position 6
     int iPos = msg.indexOf( "," );
     String SmsStorePos = msg.substring( iPos+1 );
   //  Serial.print( "SMS stored at " );
  //   Serial.println( SmsStorePos );     
     // EN: Ask to read the SMS store
     GprsReadSmsStore( SmsStorePos );
  }

  // EN: SMS store readed through UART (result of GprsReadSmsStore request)  
  if( msg.indexOf( "+CMGR:" ) >= 0 ){
    // EN: Next message will contains the BODY of SMS
    SmsContentFlag = 1;
    // EN: Following lines are essentiel to not clear the flag!
    ClearGprsMsg();
    return;
  }

  // EN: +CMGR message just before indicate that the following GRPS Shield message 
  //     (this message) will contains the SMS body 
  if( SmsContentFlag == 1 ){
 //   Serial.println( "*** SMS MESSAGE CONTENT ***" );
 //   Serial.println( msg );
 //   Serial.println( "*** END OF SMS MESSAGE ***" );
    ProcessSms( msg );
  }

  ClearGprsMsg();
  // EN: Always clear the flag
  SmsContentFlag = 0; 
}

 Hope you will help me

Original issue reported on code.google.com by jaa...@gmail.com on 16 Apr 2014 at 7:14

GoogleCodeExporter commented 8 years ago

I use the same code to control relay , but nothing happend. I use a arduino uno 
, gsm shield for this

Original comment by danielpd...@gmail.com on 5 Feb 2015 at 2:53

GoogleCodeExporter commented 8 years ago

FAKE CODE

Original comment by ilamulya...@gmail.com on 4 Jul 2015 at 8:09

GoogleCodeExporter commented 8 years ago


#include <SoftwareSerial.h>

// EN: String buffer for the GPRS shield message
String msg = String("");
// EN: Set to 1 when the next GPRS shield message will contains the SMS message
int SmsContentFlag = 0;
//control pins of relay.
int relay_a=4;
int relay_b=5;
int relay_c=6;
int relay_d=7;

// EN: Code PIN of the SIM card (if applied)
//String SIM_PIN_CODE = String( "XXXX" );

void setup()
{
  Serial.begin(9600);                 // the GPRS baud rate
  // Initialize  PINs
  pinMode( 4, OUTPUT ); 
  pinMode( 5, OUTPUT ); 
  pinMode( 6, OUTPUT ); 
  pinMode( 7, OUTPUT ); 
  digitalWrite( 4, LOW ); 
  digitalWrite( 5, LOW ); 
  digitalWrite( 6, LOW );
  digitalWrite( 7, LOW );
 Serial.println( "AT+CMGF=1" ); 
 delay(6000);
}

void loop()
{
    char SerialInByte;
    if(Serial.available())
    {       
        SerialInByte = (unsigned char)Serial.read();
       delay(5);

        // -------------------------------------------------------------------
        // EN: Program also listen to the GPRS shield message.
        // -------------------------------------------------------------------
       // EN: If the message ends with <CR> then process the message
        if( SerialInByte == 13 ){
          // EN: Store the char into the message buffer
          ProcessGprsMsg();
         }
         if( SerialInByte == 10 ){
            // EN: Skip Line feed
         }
         else {
           // EN: store the current character in the message string buffer
           msg += String(SerialInByte);
         }
     }   
}
// EN: Make action based on the content of the SMS. 
//     Notice than SMS content is the result of the processing of several GPRS 
shield messages.
void ProcessSms( String sms ){

  if( sms.indexOf("ona") >= 0 ){
    digitalWrite( relay_a, HIGH );
  }
   if( sms.indexOf("onb") >= 0 ){
    digitalWrite(  relay_b, HIGH );
  }
   if( sms.indexOf("onc") >= 0 ){
    digitalWrite(  relay_c, HIGH );
  }
  if( sms.indexOf("ond") >= 0 ){
    digitalWrite(  relay_d, HIGH );
  }
  if( sms.indexOf("offa") >= 0 ){
    digitalWrite(  relay_a, LOW );
  }
  if( sms.indexOf("offb") >= 0 ){
    digitalWrite(  relay_b, LOW );
  }
  if( sms.indexOf("offc") >= 0 ){
    digitalWrite(  relay_c, LOW );
  }
  if( sms.indexOf("offd") >= 0 ){
    digitalWrite(  relay_d, LOW );
  }
}
// EN: Request Text Mode for SMS messaging
void GprsTextModeSMS(){
  Serial.println( "AT+CMGF=1" );
}

void GprsReadSmsStore( String SmsStorePos ){
  Serial.print( "AT+CMGR=" );
  Serial.println( SmsStorePos );
}

// EN: Clear the GPRS shield message buffer
void ClearGprsMsg(){
  msg = "";
}

// EN: interpret the GPRS shield message and act appropiately
void ProcessGprsMsg() {
  if( msg.indexOf( "Call Ready" ) >= 0 ){
   //  Serial.println( "*** GPRS Shield registered on Mobile Network ***" );
     GprsTextModeSMS();
  }

  // EN: unsolicited message received when getting a SMS message
  if( msg.indexOf( "+CMTI" ) >= 0 ){
   //  Serial.println( "*** SMS Received ***" );
     // EN: Look for the coma in the full message (+CMTI: "SM",6)
     //     In the sample, the SMS is stored at position 6
     int iPos = msg.indexOf( "," );
     String SmsStorePos = msg.substring( iPos+1 );
   //  Serial.print( "SMS stored at " );
  //   Serial.println( SmsStorePos );     
     // EN: Ask to read the SMS store
     GprsReadSmsStore( SmsStorePos );
  }

  // EN: SMS store readed through UART (result of GprsReadSmsStore request)  
  if( msg.indexOf( "+CMGR:" ) >= 0 ){
    // EN: Next message will contains the BODY of SMS
    SmsContentFlag = 1;
    // EN: Following lines are essentiel to not clear the flag!
    ClearGprsMsg();
    return;
  }

  // EN: +CMGR message just before indicate that the following GRPS Shield message 
  //     (this message) will contains the SMS body 
  if( SmsContentFlag == 1 ){
 //   Serial.println( "*** SMS MESSAGE CONTENT ***" );
 //   Serial.println( msg );
 //   Serial.println( "*** END OF SMS MESSAGE ***" );
    ProcessSms( msg );
  }

  ClearGprsMsg();
  // EN: Always clear the flag
  SmsContentFlag = 0; 

I m using same code and connected my gsm module via software serial pin 9,10.
but when I send a message to on a relay nothing happens any ona can helpme.

Original comment by beerumah...@gmail.com on 10 Aug 2015 at 8:04

Adnantahir007 / gsm-shield-arduino

GPRS/SMS Shield notable to control relay #102