ASL 2.0.0 Beta 6 to ASL 3.0 Upgrade Question

[NU5D]

First and foremost THANK YOU All for the hard work and diligence that went into and continues with ASL 3. GOD SPEED.

My question.

I have a working repeater/node. The particulars - GE Mastr III - C-Media CM108 sound card - using a Wyse Dell 3040 (8gb) running ASL 2.0.0 beta 6 and all is well. USB Radio - the dsp handles squelch and ctcss encode and decode. I have discriminator (vol/sq hi) for receive, LOCAL PTT and HSD (GE’s High Speed Data - direct modulation input used with EDACS, DMR, etc) and GND.

Using the CLI Setup on 2.0.0 for USB radio there was plenty of digital pot range for my sound card config. I honestly cannot remember if I had 20 db boost enabled or not - but whichever, there was plenty of range for both send and receive. Also this is a test bed repeater - not at a site so I can tinker at will. I am using an HP8921 to look at the output and generate the input signals.

Now for the meat and potatoes - I installed Deb 12 latest and greatest on the Wyse Dell 3040 - Net Install - web server and ssh - had to add net-tools and followed the add repo / install recommendations - really nice setup.

I no longer have sufficient range in the Transmit direction - the #6 TX Voice is at 999 to get just at +/- 3 kHz transmitter deviation and the CTCSS is at 200 for +/- 750 ctcss (88.5)… and works just great !!! My question / concern - having the TX level set at max and the TX boost seems to make no difference -

This is not a gripe or complaint - just an observation and wondering if I may be missing something in my setup. Again Great Work and thanks again, steve nu5d

rpt.conf and usbradio.conf - the site would not allow attaching .conf files..

rpt dot conf

;* ;**** Template-tized rpt.conf **** ;* ; Note to editors: set tabs to 4 space characters. No wrap to keep comments neat. ; vim: tabstop=4 ; ; Radio Repeater configuration file for use with app_rpt ASL3 ;

[general] node_lookup_method = both ;method used to lookup nodes ;both = dns lookup first, followed by external file (default) ;dns = dns lookup only ;file = external file lookup only

[nodes] ; If you are using automatic update for allstar link nodes, and you probably are, ; no allstar remote nodes should be defined here. Only place a definition ; for your local nodes, and private (not on allstar directory) nodes here.

; Sample nodes on this server. These are required. Use IP 127.0.0.1 ; IAX port number if not the default 4569. ;1998 = radio@127.0.0.1/1998,NONE

; Sample public or private node behind your router. ;1001 = radio@192.168.1.8:4568/1001,NONE

; Sample private node on the internet. ;1000 = radio@8.8.8.8:4569/1000,NONE

559827 = radio@127.0.0.1/559827,NONE

node-main ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;; Template for all your nodes ;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Set the defaults for your node(s) here. ; Add your nodes below the line that says ; Add you nodes below.

;;; rxchannel ;;; ; Must also be enabled in modules.conf ; Enable the selected channel driver in modules.conf !!! ; Rx/Tx audio/signalling channel. Choose ONLY 1 per node stanza. ; rxchannel = dahdi/pseudo ; No radio (hub) ; rxchannel = SimpleUSB/1999 ; SimpleUSB ; rxchannel = Radio/1999 ; USBRadio (DSP) ; rxchannel = Voter/1999 ; RTCM device ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001 ;GNU Radio interface USRP

rxchannel = Radio/1999 ; No radio (hub)

duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional)

linkmongain = -22 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db.

erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) ;eannmode = 1 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects

;echolinkdefault = 2 ; 0 = Telemetry output off ; 1 = Telemetry output on ; 2 = Timed telemetry output on command execution and for a short time thereafter ; 3 = Follow local telemetry mode

;echolinkdynamic = 1 ; 0 = Disallow users to change current echolink telemetry setting with a COP command ; 1 = Allow users to change the setting with a COP command

controlstates = controlstates ; system control state stanza

scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza

telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza

;inxlat = *,#,0123456789ABCD,Y ; The Y is for dialtone on function, a la CACTUS ; https://wiki.allstarlink.org/wiki/Rpt.conf#inxlat.3D

context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional)

hangtime = 500 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 1000 ; longer squelch tail totime = 90000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

idrecording = |iNOTSET ; id recording or morse string ;idtalkover = ; Talkover ID (optional) default is none idtime = 540000 ; id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

;tailmessagelist=/etc/asterisk/sounds/yourtailmessage ;tailsquashedtime=900000 ; 15 minutes ;tailmessagetime=21600000 ; 6 hours (200000000 ms, 55.5555 hours is the max value possible)

unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct8 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them)

;events=events ; Events Management https://wiki.allstarlink.org/wiki/Event_Management

;lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

;lnkacttime = 1800 ; Link activity timer time in seconds. ;lnkactmacro = *52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn = 30seconds ; Message to play when the link activity timer has 30 seconds left.

;remote_inact_timeout = ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60)

;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays.

holdofftelem = 1 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node.

telemnomdb = -3 ; Telemetry Nominal Amplitude reference in dB telemduckdb = -15 ; Telemetry Ducking in dB when local or link voice tx in progress

telemdefault = 0 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter.

telemdynamic = yes ; yes = disallow users to change the local telemetry setting with a COP command ; 1 = Allow users to change the setting with a COP command. (default = 1)

;beaconing = 0 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

parrotmode = 0 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command

parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received

;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option

;startup_macro = ; Best use in your node stanza (below) when more than one node

;nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory

; Status Reporting ; Uncomment the statpost line to report the status of your node to stats.allstarlink.org ;statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

;;; End of node-main template

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;; Configure your nodes here ;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; ; Note: there is no need to duplicate entire settings. Only ; place settings that are different than the template. ;

559827 idrecording = |iK5CRA/R statpost_url = http://stats.allstarlink.org/uhandler rxchannel = Radio/559827 ;;;;;;;;;;;;;;;;;;; Your node settings here ;;;;;;;;;;;;;;;;;;; ;startup_macro = *8132000

;1998 ;;;;;;;;;;;;;;;;;;; Another node settings here ;;;;;;;;;;;;;;;;;;; ;startup_macro = *8132000 ;morse = morse_1998 ; Sample morse stanza for node 1998

[functions] ;;;;;;;;;;;;;;;;;;; functions stanza ;;;;;;;;;;;;;;;;;;; ; Prefix Functions 1 Disconnect Link 2 Monitor Link 3 Connect Link 4 Command Mode 5 Macros ; 6 User Functions 7 Connection Status/Functions 8 User Functions ; 9 User Functions ; 0 User Functions

; A User Functions ; B User Functions ; C User Functions ; D User Functions

;;;;;; Mandatory Command Codes ;;;;; 1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status 99 = cop,6 ; PTT (phone mode only)

;;;;; Macro Commands ;;;;; 5 = macro

;;;;; Autopatch Commands ;;;;; ; Note, This may be a good place for other 2 digit frequently used commands ;61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up ;62 = autopatchdn ; Autopatch down

; autopatchup can optionally take comma delimited setting=value pairs: ; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

;;;;; Status Commands ;;;;; ; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only)

721 = status,1 ; Force ID (global) 722 = status,2 ; Give Time of Day (global) 723 = status,3 ; Give software Version (global) 724 = status,4 ; Give GPS location info 725 = status,5 ; Last (dtmf) user 711 = status,11 ; Force ID (local only) 712 = status,12 ; Give Time of Day (local only)

;;;;; Link Commands ;;;;; ; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only

;;;;; ilink commands ;;;;; ; commands 1 through 5 are defined in the Mandatory Command section

; 806 = ilink,6 ; Disconnect all links ; 807 = ilink,7 ; Last Node to Key Up ; 808 = ilink,8 ; Connect specified link -- local monitor only ; 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes ; 810 = ilink,10 ; Disconnect all RANGER links (except permalinks) ; 811 = ilink,11 ; Disconnect a previously permanently connected link ; 812 = ilink,12 ; Permanently connect specified link -- monitor only ; 813 = ilink,13 ; Permanently connect specified link -- tranceive ; 815 = ilink,15 ; Full system status (all nodes) ; 816 = ilink,16 ; Reconnect links disconnected with "disconnect all links" ; 817 = ilink,17 ; MDC test (for diag purposes) ; 818 = ilink,18 ; Permanently Connect specified link -- local monitor only

;;;;; Control operator (cop) functions. ;;;;; ;Change these to something other than these codes listed below!

;901 = cop,1 ; System warm boot ;902 = cop,2 ; System enable ;903 = cop,3 ; System disable

;904 = cop,4 ; Test tone on/off (toggle) ;905 = cop,5 ; Dump system variables on console (debug use only)

;907 = cop,7 ; Time out timer enable ;908 = cop,8 ; Time out timer disable

;909 = cop,9 ; Autopatch enable ;910 = cop,10 ; Autopatch disable

;911 = cop,11 ; User linking functions enable ;912 = cop,12 ; User linking functions disable

;913 = cop,13 ; Query system control state ;914 = cop,14 ; Set system control state

;915 = cop,15 ; Scheduler enable ;916 = cop,16 ; Scheduler disable

;917 = cop,17 ; User functions enable (time, id, etc) ;918 = cop,18 ; User functions disable

;919 = cop,19 ; Select alternate hang time (althangtime) ;920 = cop,20 ; Select standard hangtime (hangtime)

;921 = cop,21 ; Enable Parrot Mode ;922 = cop,22 ; Disable Parrot Mode ;923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush)

;924 = cop,24 ; Flush all telemetry ;925 = cop,25 ; Query last node un-keyed ;926 = cop,26 ; Query all nodes keyed/unkeyed ;930 = cop,30 ; Recall Memory Setting in Attached Xcvr

;931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr

;932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed

;933 = cop,33 ; Local Telemetry Output Enable ;934 = cop,34 ; Local Telemetry Output Disable ;935 = cop,35 ; Local Telemetry Output on Demand

;936 = cop,36 ; Foreign Link Local Output Path Enable ;937 = cop,37 ; Foreign Link Local Output Path Disable ;938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry ;939 = cop,39 ; Foreign Link Local Output Path on Demand

;942 = cop,42 ; Echolink announce node # only ;943 = cop,43 ; Echolink announce node Callsign only ;944 = cop,44 ; Echolink announce node # & Callsign

;945 = cop,45 ; Link Activity timer enable ;945 = cop,46 ; Link Activity timer disable ;947 = cop,47 ; Reset "Link Config Changed" Flag

;948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis)

; 949 = cop,49 ; Disable incoming connections (control state noice) ; 950 = cop,50 ; Enable incoming connections (control state noicd)

; 951 = cop,51 ; Enable sleep mode ; 952 = cop,52 ; Disable sleep mode ; 953 = cop,53 ; Wake up from sleep ; 954 = cop,54 ; Go to sleep ; 955 = cop,55 ; Parrot Once if parrot mode is disabled

; 956 = cop,56 ; Rx CTCSS Enable ; 957 = cop,57 ; Rx CTCSS Disable

; 958 = cop.58 ; Tx CTCSS On Input only Enable ; 959 = cop,59 ; Tx CTCSS On Input only Disable

; 960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; DestID and subcode are only specified for the 'C' type message. ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; the radio being called, and the subcodes are as follows: ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; Astro-Saber('Call') ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

; 961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) ; 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

; 963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) ; 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) ; 965 = cop,65 ; Send POCSAG page (equipped channel types only)

; [functions-remote] ;;;;; Functions for remote bases ;;;;; ; ; 0 = remote,1 ; Retrieve Memory ; 1 = remote,2 ; Set freq. ; 2 = remote,3 ; Set tx PL tone ; 3 = remote,4 ; Set rx PL tone ; 40 = remote,100 ; Rx PL off ; 41 = remote,101 ; Rx PL on ; 42 = remote,102 ; Tx PL off ; 43 = remote,103 ; Tx PL on ; 44 = remote,104 ; Low Power ; 45 = remote,105 ; Medium Power ; 46 = remote,106 ; High Power ; 711 = remote,107 ; Bump -20 ; 714 = remote,108 ; Bump -100 ; 717 = remote,109 ; Bump -500 ; 713 = remote,110 ; Bump +20 ; 716 = remote,111 ; Bump +100 ; 719 = remote,112 ; Bump +500 ; 721 = remote,113 ; Scan - slow ; 724 = remote,114 ; Scan - quick ; 727 = remote,115 ; Scan - fast ; 723 = remote,116 ; Scan + slow ; 726 = remote,117 ; Scan + quick ; 729 = remote,118 ; Scan + fast ; 79 = remote,119 ; Tune ; 51 = remote,5 ; Long status query ; 52 = remote,140 ; Short status query ; 67 = remote,210 ; Send a * ; 69 = remote,211 ; Send a # ; 91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. ; 85 = cop,6 ; Remote base telephone key

[telemetry] ;;;;; Telemetry ;;;;; ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ;

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ct9 = |t(1633,0,50,1000)(0,0,30,0)(1209,0,50,1000); ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated

; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

[morse] ;;;;; Mores code ;;;;; ; Morse code parameters, these are common to all repeaters. speed = 20 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude

;[morse] ;speed = 35 ; Not leagle in the USA ;frequency = 800 ; Morse Telemetry Frequency Changed ;amplitude = 4096 ; Morse Telemetry Amplitude ;idfrequency = 750 ; Morse ID Frequency Changed ;idamplitude = 512 ; Morse ID Amplitude *Changed

[wait-times] ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater telemwait = 0500 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 0500 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 0500 ; Time to wait before announcing "call terminated"

[wait-times_hd] ; Sample for half-duplex telemwait = 100 ; Time to wait before sending most telemetry idwait = 100 ; Time to wait before starting ID unkeywait = 100 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 2000 ; Time to wait before announcing "call terminated"

[memory] ;;;;; Remote base memories ;;;;; ; Memories for remote bases (not for repeaters or hotspots). Seldom used. ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m

[macro] ;;;;; Macro commands ;;;;; ;1 = 812000 ;2 = 822000 ;3 = 832000 ;4 = 31998*32000

;[daq-list] ;;;;; Data Acquisition configuration ;;;;; ;Where: device_name1 and device_name2 are stanzas you define in this file ;device = daq-cham-1 ;device = device_name1 ;device = device_name2

;[daq-cham-1] ; Defined in [daq-list] ; Device name ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out

;[meter-faces] ; ;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,?

;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,7,- ;pwrfail = daq-cham-1,10,0,2017,911111,-

;[events] ;;;;; Events Management ;;;;; ;status,2 = c|f|RPT_NUMLINKS ; Say time of day when all links disconnect.

[controlstates] ;;;;; Control states ;;;;; ; Allow several control operator functions to be changed at once using one command (good for scheduling) ;statenum = copcmd,[copcmd]... https://wiki.allstarlink.org/wiki/Rpt.conf#Control_States_Stanza 0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation 1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation 2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation

[schedule] ;;;;; Scheduler - execute a macro at a given time ;;;;; ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;2 = 00 00 * ; at midnight, execute macro 2.

#########################################################################################

usbradio.conf

;! ;! Automatically generated configuration file ;! Filename: usbradio.conf (/etc/asterisk/usbradio.conf) ;! Generator: chan_usbradio ;! Creation Date: Wed Jul 3 17:52:24 2024 ;! ;** ;**** Template-tized usbradio.conf **** ;** ; Note to editors: set tabs to 4 space characters. No wrap to keep comments neat. ; vim: tabstop=4 ; ; USBRadio channel driver Configuration File ; ;;;;; New to ASL3 ;;;;; ;;;;; The USBRadio "tune" settings have moved to ;;;;; ;;;;; this file. The usbradio_tune_usb_1999.conf ;;;;; ;;;;; file is no longer used. ;;;;;

; If you are going to use this channel driver, you MUST enable it in modules.conf ; noload => chan_usbradio.so ; CM1xx USB Cards with Radio Interface Channel Driver (DSP) ; noload => res_usbradio.so ; Required for both simpleusb and usbradio ; to: ; load => chan_usbradio.so ; CM1xx USB Cards with Radio Interface Channel Driver (DSP) ; load => res_usbradio.so ; Required for both simpleusb and usbradio

[general] ;------------------------------ JITTER BUFFER CONFIGURATION -------------------------- ; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of an ; USBRADIO channel. Defaults to "no". An enabled jitterbuffer will ; be used only if the sending side can create and the receiving ; side can not accept jitter. The USBRADIO channel can't accept jitter, ; thus an enabled jitterbuffer on the receive USBRADIO side will always ; be used if the sending side can create jitter.

; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.

; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is ; resynchronized. Useful to improve the quality of the voice, with ; big jumps in/broken timestamps, usualy sent from exotic devices ; and programs. Defaults to 1000.

; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of an USBRADIO ; channel. Two implementations are currenlty available - "fixed" ; (with size always equals to jbmax-size) and "adaptive" (with ; variable size, actually the new jb of IAX2). Defaults to fixed.

; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no". ;-----------------------------------------------------------------------------------

node-main ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;; Template for all your USBRadio nodes ;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

eeprom = 0 ; EEPROM installed: 0,1 ; 0 = no (default) ; 1 = yes

hdwtype = 0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces.

rxboost = yes ; no - 20db attenuator inserted ; yes - 20db attenuator removed ; Set to yes for additonal gain if using a low-level receiver output ; CM119B devices are hard coded to rxboost 20dB attenuator removed

rxctcssrelax = 1 ; reduce talkoff from radios w/o CTCSS TX HPF ; Do not change this, leave this as a 1

rxsqhyst = 500 ; Setting Squelch Hysteresis ; 3000 is the default amount. ; An amount of 500 seems good. ; Then set the squelch to the highest number revealed when doing a "radio ; tune rxsquelch" - running the command multiple (like 20) times in a row.

txctcssdefault = 88.5 ; default TX CTCSS frequency, any frequency permitted rxctcssfreqs = 88.5 ; RX CTCSS frequencies list in floating point. must be in table txctcssfreqs = 88.5 ; TX CTCSS frequencies list. any frequency permitted. will follow RX CTCSS frequency rxctcssoverride = no ; Set to yes to start out in carrier squelch mode

carrierfrom = dsp ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the USB sound fob (Active high) ; usbinvert - from the inverted COR line on the USB sound fob (Active low) ; dsp - from RX noise using DSP techniques ; vox - voice activated from RX audio

ctcssfrom = dsp ; no,usb,usbinvert,dsp ; no - no CTCSS decoding, system will be carrier squelch ; usb - from the CTCSS line on the USB sound fob (Active high) ; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work.

rxdemod = flat ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio

rxsquelchdelay = 30 ; delayline in ms carrier squelch tail eliminator

rxondelay = 0 ; Number of 20mSec intervals following the release of PTT. ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". A positive value here will instruct the usbradio ; driver to ignore the COR line for a specified number of 20mSec ; intervals following the release of PTT. Use this ONLY on simplex ; nodes, and leave commented out for repeaters or other full duplex nodes.

txoffdelay = 0 ; Ignore the reciever for a specified number of 20 millisecond ; intervals after the transmitter unkeys. ; This is useful when setting up a half-duplex link with an existing ; repeater, where you need to ignore the repeater's hangtime.

txboost = no ; Add transmitter audio gain boost: no,yes

txprelim = yes ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; (suitable for use on a microphone input) ; yes - Audio is pre-emphasized and limited. ; (suitable for direct connection to an FM modulator)

txlimonly = yes ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis.

txtoctype = notone ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst")

txmixa = composite ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring

txmixb = no ; Right channel output: no,voice,tone,composite, auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring

; Audio filters rxlpf = 0 ; Receiver Audio Low Pass Filter 0,1 2 ; 0 - 3.0 kHz cutoff (Default) value for reduced noise and increased intelligibility. ; 1 - 3.3 kHz cutoff for increased high end, sibilance and brightness. ; 2 - 3.5 kHz cutoff for even more high end, sibilance and brightness. rxhpf = 0 ; Receiver Audio High Pass Filter 0,1 ; 0 - 300 Hz cutoff. (Default) value to reduce sub-audible signals for retransmission and in the receiver speaker. ; 1 - 250 Hz cutoff for additional received and retransmitted bass response. ; recommend using this filter with a CTCSS tone no higher than 186.2 Hz. txlpf = 0 ; Transmitter Audio Low Pass Filter 0,1 ; 0 - 3.0 kHz cutoff. (Default) value. ; 1 - 3.3 kHz cutoff for increased high end, sibilance and brightness. txhpf = 0 ; Transmitter Audio High Pass Filter 0,1,2 ; 0 - 300 Hz cutoff. (Default) value to reduce interference between voice and sub-audible signaling tones and codes. ; 1 - 250 Hz cutoff for increased bass response in transmitted audio. ; 2 - 120 Hz cutoff for special applications requiring additional bass response in transmitted audio. ; Not recommended due to the increased possibility of voice energy interfering with sub-audible signaling

invertptt = no ; Invert PTT: no,yes ; no - ground to transmit ; yes - open to transmit

duplex = 1 ; Duplex 0,1 ; 0 - half duplex ; 1 - full duplex duplex3 = 0 ; duplex 3 gain setting (0 to disable) ???

;;; End of node-main template

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;; Configure your nodes here ;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; ; Note: there is no need to duplicate entire settings. Only ; place settings that are different than the template. ; ; Note: the device string is automatically found when the ; USB setting "devstr=" is empty. ; ; Note: the interface "tune" settings will be added to the ; per-node settings (below).

559827

txboost = yes

;;;;; ASL3 Tune settings ;;;;; devstr = 1-1:1.0 rxmixerset = 875 txmixaset = 999 txmixbset = 990 rxvoiceadj = 1.000000 rxctcssadj = 0.908583 txctcssadj = 200 rxsquelchadj = 851

These are the new Version 3 files - I will have to do some digging to get the version 2.0.0 beta 6 files.

steve nu5d

[tsawyer]

@KB4MDD This might be a question you can address. Please take a look.

[KB4MDD]

I will take a look.

[NU5D]

I made a mistake. Please forgive my error - This morning I set up a 2nd Wyse Dell 3040 - with ASL 2.0.0 Beta 6, and I had the very same results. There is nothing wrong with Rev 3. Rev 2.0.0 required the same settings. TX 990 for almost 3 kHz Transmitter deviation. There is no issue. Thank all for the very prompt response and again I am very sorry for the false alarm. 73, Steve NU5D..

[KB4MDD]

Closing no action needed.