Raspberry Pi 4 - Does this board work with AllSky

[spacemanbobby]

I remember when the 4 boards came out that there was some issues with it not working quite right....

Now that they have been out a while.. Has this been updated and does the AllSky work with them after installing all the normal files... I have copies of my older paths for FTP etc.. that I can just place after.

[Dentonknifeworks]

I have been running mine on a PI4 for 2 months now.

[Alex-developer]

Works 100%

[spacemanbobby]

I'm getting serious image corruption during the day.. Nothing at night but crazy scrambled images...

On Wed, Aug 12, 2020 at 12:36 PM Alex notifications@github.com wrote:

Works 100%

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673069713, or unsubscribe https://github.com/notifications/unsubscribe-auth/AK2MJOUFGVGBFWOZ3374QHDSALVNHANCNFSM4PWXH5XQ .

[thomasjacquin]

The Pi 4 works. Your issue is probably caused by something else such as slow wireless connection or frame rate too high during the day (increase daytime delay).

[spacemanbobby]

Ok... didn't have this with the Pi3 version. But I'll check things out this weekend. I have the daytime delay set to 30 seconds. I am going to turn off the stretch option. Also...

On Wed, Aug 12, 2020 at 1:26 PM Thomas Jacquin notifications@github.com wrote:

The Pi 4 works. Your issue is probably caused by something else such as slow wireless connection or frame rate too high during the day (increase daytime delay).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673093037, or unsubscribe https://github.com/notifications/unsubscribe-auth/AK2MJOTVAO3PAV7OT64CXB3SAL3GRANCNFSM4PWXH5XQ .

[curitsreno]

Don't know if this helps or not. I have an ASI120mc and tried it on both a PI3 and 4. Same results, or at least similar results. Good one second then weird scrambled picture, I would get bars across the screen or the screen would break up into 2 to 4 parts and be reassembled the wrong way. And what fixes it for me is changing resolution from 0, 0 on the height, width settings to 1200 x 950. Once I back down the resolution to those specific numbers it never fails again. I went to the PI 4 hoping it would fix the issue, thinking that usb2 was causing the issues, but it didn't fix it.

I think there are some serious issues with the canned drivers for this camera and raspberry PI boards. Wish the hardware manufacturer (ASI120mc) would step in and release proper drivers.

On Wed, Aug 12, 2020 at 5:04 PM spacemanbobby notifications@github.com wrote:

Ok... didn't have this with the Pi3 version. But I'll check things out this weekend. I have the daytime delay set to 30 seconds. I am going to turn off the stretch option. Also...

On Wed, Aug 12, 2020 at 1:26 PM Thomas Jacquin notifications@github.com wrote:

The Pi 4 works. Your issue is probably caused by something else such as slow wireless connection or frame rate too high during the day (increase daytime delay).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub < https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673093037 , or unsubscribe < https://github.com/notifications/unsubscribe-auth/AK2MJOTVAO3PAV7OT64CXB3SAL3GRANCNFSM4PWXH5XQ

.

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673109914, or unsubscribe https://github.com/notifications/unsubscribe-auth/AQIAZ4EV6P45WBN4IKMP2N3SAL7U5ANCNFSM4PWXH5XQ .

--

Curtis RenoSystems Administrator

Lorain County Public Health 9880 South Murray Ridge Rd., Elyria, OH 44035

Office: (440) 322-6367 Mobile: (440) 935-0447 Fax: (440) 322-0911

LorainCountyHealth.com https://www.loraincountyhealth.com/

[image: https://docs.google.com/uc?export=download&id=16PeTMPSqh3fLWOBU3bO-d0stmbqFddS3&revid=0B5ssixkst1F1b3VUNjI0aGV2cHEwd08zaUVyNlZjYXIveXJzPQ]

[spacemanbobby]

Ok... In my config I have an ASI185 and I uncommented that line out to use that in my Pi4 Board.. I looked at my old config in my Pi3 board and saw that even though I was using the asi185mc I was using the config for the the other asi camera.. So I changed it in the pi4 board to the original. Now I am getting images with no garbled lines in it.

On Thu, Aug 13, 2020 at 5:24 AM curitsreno notifications@github.com wrote:

Don't know if this helps or not. I have an ASI120mc and tried it on both a PI3 and 4. Same results, or at least similar results. Good one second then weird scrambled picture, I would get bars across the screen or the screen would break up into 2 to 4 parts and be reassembled the wrong way. And what fixes it for me is changing resolution from 0, 0 on the height, width settings to 1200 x 950. Once I back down the resolution to those specific numbers it never fails again. I went to the PI 4 hoping it would fix the issue, thinking that usb2 was causing the issues, but it didn't fix it.

I think there are some serious issues with the canned drivers for this camera and raspberry PI boards. Wish the hardware manufacturer (ASI120mc) would step in and release proper drivers.

On Wed, Aug 12, 2020 at 5:04 PM spacemanbobby notifications@github.com wrote:

Ok... didn't have this with the Pi3 version. But I'll check things out this weekend. I have the daytime delay set to 30 seconds. I am going to turn off the stretch option. Also...

On Wed, Aug 12, 2020 at 1:26 PM Thomas Jacquin <notifications@github.com

wrote:

The Pi 4 works. Your issue is probably caused by something else such as slow wireless connection or frame rate too high during the day (increase daytime delay).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <

https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673093037

, or unsubscribe <

https://github.com/notifications/unsubscribe-auth/AK2MJOTVAO3PAV7OT64CXB3SAL3GRANCNFSM4PWXH5XQ

.

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub < https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673109914 , or unsubscribe < https://github.com/notifications/unsubscribe-auth/AQIAZ4EV6P45WBN4IKMP2N3SAL7U5ANCNFSM4PWXH5XQ

.

--

Curtis RenoSystems Administrator

Lorain County Public Health 9880 South Murray Ridge Rd., Elyria, OH 44035

Office: (440) 322-6367 Mobile: (440) 935-0447 Fax: (440) 322-0911

LorainCountyHealth.com https://www.loraincountyhealth.com/

[image:

https://docs.google.com/uc?export=download&id=16PeTMPSqh3fLWOBU3bO-d0stmbqFddS3&revid=0B5ssixkst1F1b3VUNjI0aGV2cHEwd08zaUVyNlZjYXIveXJzPQ ]

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673446076, or unsubscribe https://github.com/notifications/unsubscribe-auth/AK2MJOQRYN6TU56T3WFV7P3SAPLOHANCNFSM4PWXH5XQ .

[spacemanbobby]

I have noticed that the Dark frame isn't taking or isn't being applied. My images have all sorts of heat noise on them. I have the dark frame option turned on at night and it just doesn't seem to be applied to any of the images. I am taking jpg images and quality is set to 100. I take the dark around 9pm my time and then switch it back to off. Here is a link to the days video for August 13th. The early part was before I changed the config to use the default asi camera... thus the bad images in the beginning. http://spacemanbob.com/allsksy/videos/allsky-20200813.mp4

This is the path... from the configs section

Path to the dark frame for hot pixels subtraction. Can be jpg or png.

DARK_FRAME="dark.jpg"

On Wed, Aug 12, 2020 at 1:26 PM Thomas Jacquin notifications@github.com wrote:

The Pi 4 works. Your issue is probably caused by something else such as slow wireless connection or frame rate too high during the day (increase daytime delay).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673093037, or unsubscribe https://github.com/notifications/unsubscribe-auth/AK2MJOTVAO3PAV7OT64CXB3SAL3GRANCNFSM4PWXH5XQ .

[DarKOrange75]

Ok... In my config I have an ASI185 and I uncommented that line out to use that in my Pi4 Board.. I looked at my old config in my Pi3 board and saw that even though I was using the asi185mc I was using the config for the the other asi camera.. So I changed it in the pi4 board to the original. Now I am getting images with no garbled lines in it. … On Thu, Aug 13, 2020 at 5:24 AM curitsreno @.> wrote: Don't know if this helps or not. I have an ASI120mc and tried it on both a PI3 and 4. Same results, or at least similar results. Good one second then weird scrambled picture, I would get bars across the screen or the screen would break up into 2 to 4 parts and be reassembled the wrong way. And what fixes it for me is changing resolution from 0, 0 on the height, width settings to 1200 x 950. Once I back down the resolution to those specific numbers it never fails again. I went to the PI 4 hoping it would fix the issue, thinking that usb2 was causing the issues, but it didn't fix it. I think there are some serious issues with the canned drivers for this camera and raspberry PI boards. Wish the hardware manufacturer (ASI120mc) would step in and release proper drivers. On Wed, Aug 12, 2020 at 5:04 PM spacemanbobby @.> wrote: > Ok... didn't have this with the Pi3 version. But I'll check things out this > weekend. I have the daytime delay set to 30 seconds. I am going to turn off > the stretch option. Also... > > On Wed, Aug 12, 2020 at 1:26 PM Thomas Jacquin @.** > > wrote: > > > The Pi 4 works. Your issue is probably caused by something else such as > > slow wireless connection or frame rate too high during the day (increase > > daytime delay). > > > > — > > You are receiving this because you authored the thread. > > Reply to this email directly, view it on GitHub > > < > #215 (comment) > >, > > or unsubscribe > > < > https://github.com/notifications/unsubscribe-auth/AK2MJOTVAO3PAV7OT64CXB3SAL3GRANCNFSM4PWXH5XQ > > > > . > > > > — > You are receiving this because you are subscribed to this thread. > Reply to this email directly, view it on GitHub > < #215 (comment) >, > or unsubscribe > < https://github.com/notifications/unsubscribe-auth/AQIAZ4EV6P45WBN4IKMP2N3SAL7U5ANCNFSM4PWXH5XQ > > . > -- Curtis RenoSystems Administrator Lorain County Public Health* 9880 South Murray Ridge Rd., Elyria, OH 44035 Office: (440) 322-6367 Mobile: (440) 935-0447 Fax: (440) 322-0911 LorainCountyHealth.com https://www.loraincountyhealth.com/ [image: https://docs.google.com/uc?export=download&id=16PeTMPSqh3fLWOBU3bO-d0stmbqFddS3&revid=0B5ssixkst1F1b3VUNjI0aGV2cHEwd08zaUVyNlZjYXIveXJzPQ ] — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#215 (comment)>, or unsubscribe https://github.com/notifications/unsubscribe-auth/AK2MJOQRYN6TU56T3WFV7P3SAPLOHANCNFSM4PWXH5XQ .

Hi, which line and in which file did you uncomment ?

[spacemanbobby]

I had uncommented out the old config where you would use the asi185 settings... I have since just wiped the buster pi software and started from scratch. New Pi software image... and new AllSky download. Looks like things are all working.. I think it was a combo of issues at first.. Old buster install and an older allsky download... combined with updating both...

Now I am just running my asi185 on the default installed software and everything seems to be working.

On Sun, Aug 16, 2020 at 11:29 PM DarKOrange75 notifications@github.com wrote:

Ok... In my config I have an ASI185 and I uncommented that line out to use that in my Pi4 Board.. I looked at my old config in my Pi3 board and saw that even though I was using the asi185mc I was using the config for the the other asi camera.. So I changed it in the pi4 board to the original. Now I am getting images with no garbled lines in it. … <#m-800220691939010648> On Thu, Aug 13, 2020 at 5:24 AM curitsreno @.> wrote: Don't know if this helps or not. I have an ASI120mc and tried it on both a PI3 and 4. Same results, or at least similar results. Good one second then weird scrambled picture, I would get bars across the screen or the screen would break up into 2 to 4 parts and be reassembled the wrong way. And what fixes it for me is changing resolution from 0, 0 on the height, width settings to 1200 x 950. Once I back down the resolution to those specific numbers it never fails again. I went to the PI 4 hoping it would fix the issue, thinking that usb2 was causing the issues, but it didn't fix it. I think there are some serious issues with the canned drivers for this camera and raspberry PI boards. Wish the hardware manufacturer (ASI120mc) would step in and release proper drivers. On Wed, Aug 12, 2020 at 5:04 PM spacemanbobby @.> wrote: > Ok... didn't have this with the Pi3 version. But I'll check things out this > weekend. I have the daytime delay set to 30 seconds. I am going to turn off > the stretch option. Also... > > On Wed, Aug 12, 2020 at 1:26 PM Thomas Jacquin @.*** > > wrote: > > > The Pi 4 works. Your issue is probably caused by something else such as > > slow wireless connection or frame rate too high during the day (increase >

daytime delay). > > > > — > > You are receiving this because you authored the thread. > > Reply to this email directly, view it on GitHub > > < > #215 (comment) https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673093037

, > > or unsubscribe > > < > https://github.com/notifications/unsubscribe-auth/AK2MJOTVAO3PAV7OT64CXB3SAL3GRANCNFSM4PWXH5XQ

. > > > > — > You are receiving this because you are subscribed to this thread. > Reply to this email directly, view it on GitHub > < #215 (comment) https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673109914 , > or unsubscribe > < https://github.com/notifications/unsubscribe-auth/AQIAZ4EV6P45WBN4IKMP2N3SAL7U5ANCNFSM4PWXH5XQ . > -- Curtis RenoSystems Administrator Lorain County Public Health 9880 South Murray Ridge Rd., Elyria, OH 44035 Office: (440) 322-6367 Mobile: (440) 935-0447 Fax: (440) 322-0911 LorainCountyHealth.com https://www.loraincountyhealth.com/ [image: https://docs.google.com/uc?export=download&id=16PeTMPSqh3fLWOBU3bO-d0stmbqFddS3&revid=0B5ssixkst1F1b3VUNjI0aGV2cHEwd08zaUVyNlZjYXIveXJzPQ ] — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#215 (comment) https://github.com/thomasjacquin/allsky/issues/215#issuecomment-673446076>, or unsubscribe https://github.com/notifications/unsubscribe-auth/AK2MJOQRYN6TU56T3WFV7P3SAPLOHANCNFSM4PWXH5XQ .

Hi, which line and in which file did you uncomment ?

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/thomasjacquin/allsky/issues/215#issuecomment-674686922, or unsubscribe https://github.com/notifications/unsubscribe-auth/AK2MJOT2UQWOP5E2XUKY5ILSBDE3JANCNFSM4PWXH5XQ .

[EricClaeys]

This issue is from an older release of the AllSky software. If you think it might still be relevant, please test it with the newest version and submit a new issue if needed. Thanks.