gptp daemons is not loading due to this erro : GPTP [17:42:25:660] Failed to configure timestamping: Operation not supported

[iamdharm20]

Hi,

i am not able to load the gptp daemons due to the below errors:

root@KOR1064342VM:/gitweb/OpenAvnu-open-avb-next/daemons/gptp/linux/build# /home/dus5cob/gitweb/OpenAvnu-open-avb-next/daemons/gptp/linux/build/obj/daemon_cl eth1 > ptp.log & [4] 13897 root@KOR1064342VM:/gitweb/OpenAvnu-open-avb-next/daemons/gptp/linux/build# INFO : GPTP [17:42:25:659] gPTP starting ERROR : GPTP [17:42:25:660] Failed to configure timestamping: Operation not supported ERROR : GPTP [17:42:25:660] post_init failed

ERROR : GPTP [17:42:25:660] failed to initialize port ^C

this issue is already resolved by this patch https://review.tizen.org/gerrit/24785 but still i am facing the same problem.

setup : ubuntu 14lts intel 210-T1 gbi NIC network adapter :

eth1 Link encap:Ethernet HWaddr 08:00:27:e3:7c:d9 inet addr:172.17.0.8 Bcast:172.17.0.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fee3:7cd9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:898 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2208 (2.2 KB) TX bytes:83495 (83.4 KB)

i am following this procedure to compile the source code:

cloned this branch : OpenAvnu-open-avb-next make EXTRA_CFLAGS="-DIGB_PTP"

then i have loaded all these module. sudo modprobe i2c_algo_bit sudo modprobe dca sudo modprobe ptp sudo insmod /home/dus5cob/gitweb/OpenAvnu-open-avb-next/kmod/igb/igb_avb.ko

finaly i run this gptp daemons /home/dus5cob/gitweb/OpenAvnu-open-avb-next/daemons/gptp/linux/build/obj/daemon_cl eth1 > ptp.log & but i face this error : ERROR : GPTP [17:42:25:660] Failed to configure timestamping: Operation not supported ERROR : GPTP [17:42:25:660] Failed to configure timestamping: Operation not supported ERROR : GPTP [17:42:25:660] post_init failed

could you please guide me what is the problem and what should be the solution for this ?

Regrads, Dharmender sharma

[christopher-s-hall]

Did you unload all of the drivers (e.g. igb) managing that interface? If that doesn't work, please post the dmesg output generated when the driver is loaded.

[iamdharm20]

yes i have unloaded all the drivers properly.

[iamdharm20]

sorry i am not able to upload the dmesg file but please find the logs :

[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.13.0-112-generic (buildd@lcy01-02) (gcc version 4.8.4 (Ubuntu 4.8.4-2ubuntu1~14.04.3) ) #159-Ubuntu SMP Fri Mar 3 15:26:07 UTC 2017 (Ubuntu 3.13.0-112.159-generic 3.13.11-ckt39) [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.13.0-112-generic root=/dev/mapper/kor1030612--vg-root ro quiet splash vt.handoff=7 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dffeffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000dfff0000-0x00000000dfffffff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000002e45fffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.5 present. [ 0.000000] DMI: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x2e4600 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR variable ranges disabled: [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] CPU MTRRs all blank - virtualized system. [ 0.000000] e820: last_pfn = 0xdfff0 max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x0009fff0-0x0009ffff] mapped at [ffff88000009fff0] [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576 [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] BRK [0x01fe3000, 0x01fe3fff] PGTABLE [ 0.000000] BRK [0x01fe4000, 0x01fe4fff] PGTABLE [ 0.000000] BRK [0x01fe5000, 0x01fe5fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x2e4400000-0x2e45fffff] [ 0.000000] [mem 0x2e4400000-0x2e45fffff] page 2M [ 0.000000] BRK [0x01fe6000, 0x01fe6fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x2e4000000-0x2e43fffff] [ 0.000000] [mem 0x2e4000000-0x2e43fffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x280000000-0x2e3ffffff] [ 0.000000] [mem 0x280000000-0x2e3ffffff] page 2M [ 0.000000] BRK [0x01fe7000, 0x01fe7fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x00100000-0xdffeffff] [ 0.000000] [mem 0x00100000-0x001fffff] page 4k [ 0.000000] [mem 0x00200000-0xdfdfffff] page 2M [ 0.000000] [mem 0xdfe00000-0xdffeffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x100000000-0x27fffffff] [ 0.000000] [mem 0x100000000-0x27fffffff] page 2M [ 0.000000] BRK [0x01fe8000, 0x01fe8fff] PGTABLE [ 0.000000] RAMDISK: [mem 0x357f6000-0x36bf2fff] [ 0.000000] ACPI: RSDP 00000000000e0000 000024 (v02 VBOX ) [ 0.000000] ACPI: XSDT 00000000dfff0030 00003C (v01 VBOX VBOXXSDT 00000001 ASL 00000061) [ 0.000000] ACPI: FACP 00000000dfff00f0 0000F4 (v04 VBOX VBOXFACP 00000001 ASL 00000061) [ 0.000000] ACPI: DSDT 00000000dfff0480 001B96 (v01 VBOX VBOXBIOS 00000002 INTL 20100528) [ 0.000000] ACPI: FACS 00000000dfff0200 000040 [ 0.000000] ACPI: APIC 00000000dfff0240 000064 (v02 VBOX VBOXAPIC 00000001 ASL 00000061) [ 0.000000] ACPI: SSDT 00000000dfff02b0 0001CC (v01 VBOX VBOXCPUT 00000002 INTL 20100528) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x00000002e45fffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x2e45fffff] [ 0.000000] NODE_DATA [mem 0x2e45f2000-0x2e45f6fff] [ 0.000000] [ffffea0000000000-ffffea000b9fffff] PMD -> [ffff8802d8a00000-ffff8802e3bfffff] on node 0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x2e45fffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x0009efff] [ 0.000000] node 0: [mem 0x00100000-0xdffeffff] [ 0.000000] node 0: [mem 0x100000000-0x2e45fffff] [ 0.000000] On node 0 totalpages: 2901390 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 21 pages reserved [ 0.000000] DMA zone: 3998 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14272 pages used for memmap [ 0.000000] DMA32 zone: 913392 pages, LIFO batch:31 [ 0.000000] Normal zone: 31000 pages used for memmap [ 0.000000] Normal zone: 1984000 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 3, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] smpboot: Allowing 3 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xdfff0000-0xdfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xfffbffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfffc0000-0xffffffff] [ 0.000000] e820: [mem 0xe0000000-0xfffbffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:3 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff8802e4200000 s81536 r8192 d20864 u524288 [ 0.000000] pcpu-alloc: s81536 r8192 d20864 u524288 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 - [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2856033 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.13.0-112-generic root=/dev/mapper/kor1030612--vg-root ro quiet splash vt.handoff=7 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Memory: 11319764K/11605560K available (7432K kernel code, 1147K rwdata, 3424K rodata, 1340K init, 1448K bss, 285796K reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=3, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=3. [ 0.000000] Offload RCU callbacks from all CPUs [ 0.000000] Offload RCU callbacks from CPUs: 0-2. [ 0.000000] NR_IRQS:16640 nr_irqs:704 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 46661632 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 3555.912 MHz processor [ 0.004006] Calibrating delay loop (skipped), value calculated using timer frequency.. 7111.82 BogoMIPS (lpj=14223648) [ 0.004009] pid_max: default: 32768 minimum: 301 [ 0.004031] Security Framework initialized [ 0.004045] AppArmor: AppArmor initialized [ 0.004047] Yama: becoming mindful. [ 0.004877] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.008337] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.009640] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.009654] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.009826] Initializing cgroup subsys memory [ 0.009831] Initializing cgroup subsys devices [ 0.009833] Initializing cgroup subsys freezer [ 0.009836] Initializing cgroup subsys blkio [ 0.009838] Initializing cgroup subsys perf_event [ 0.009841] Initializing cgroup subsys hugetlb [ 0.009910] CPU: Physical Processor ID: 0 [ 0.009912] CPU: Processor Core ID: 0 [ 0.009916] mce: CPU supports 0 MCE banks [ 0.009943] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.009943] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0 [ 0.009943] tlb_flushall_shift: 6 [ 0.010075] Freeing SMP alternatives memory: 32K (ffffffff81e6f000 - ffffffff81e77000) [ 0.015264] ACPI: Core revision 20131115 [ 0.015771] ACPI: All ACPI Tables successfully acquired [ 0.015799] ftrace: allocating 28674 entries in 113 pages [ 0.028295] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.068657] smpboot: CPU0: Intel(R) Core(TM) i7-4790 CPU @ 3.60GHz (fam: 06, model: 3c, stepping: 03) [ 0.072000] Performance Events: unsupported p6 CPU model 60 no PMU driver, software events only. [ 0.072000] x86: Booting SMP configuration: [ 0.080728] NMI watchdog: disabled (cpu0): hardware events not enabled [ 0.072000] mce: CPU supports 0 MCE banks [ 0.082899] mce: CPU supports 0 MCE banks [ 0.072000] .... node #0, CPUs: #1 #2 [ 0.096039] x86: Booted up 1 node, 3 CPUs [ 0.096042] smpboot: Total of 3 processors activated (21335.47 BogoMIPS) [ 0.096508] devtmpfs: initialized [ 0.098416] EVM: security.selinux [ 0.098419] EVM: security.SMACK64 [ 0.098421] EVM: security.ima [ 0.098423] EVM: security.capability [ 0.100604] pinctrl core: initialized pinctrl subsystem [ 0.100660] regulator-dummy: no parameters [ 0.100692] RTC time: 12:51:03, date: 03/29/17 [ 0.100718] NET: Registered protocol family 16 [ 0.100790] cpuidle: using governor ladder [ 0.100792] cpuidle: using governor menu [ 0.100815] ACPI: bus type PCI registered [ 0.100818] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.100887] PCI: Using configuration type 1 for base access [ 0.101528] bio: create slab at 0 [ 0.101528] ACPI: Added _OSI(Module Device) [ 0.101528] ACPI: Added _OSI(Processor Device) [ 0.101528] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.101528] ACPI: Added _OSI(Processor Aggregator Device) [ 0.101528] ACPI: Executed 1 blocks of module-level executable AML code [ 0.104398] ACPI: Interpreter enabled [ 0.104403] ACPI Exception: AE_NOTFOUND, While evaluating Sleep State [_S1] (20131115/hwxface-580) [ 0.104407] ACPI Exception: AE_NOTFOUND, While evaluating Sleep State [_S2] (20131115/hwxface-580) [ 0.104410] ACPI Exception: AE_NOTFOUND, While evaluating Sleep State [_S3] (20131115/hwxface-580) [ 0.104414] ACPI Exception: AE_NOTFOUND, While evaluating Sleep State [_S4] (20131115/hwxface-580) [ 0.104419] ACPI: (supports S0 S5) [ 0.104421] ACPI: Using IOAPIC for interrupt routing [ 0.104531] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug [ 0.104558] ACPI: No dock devices found. [ 0.106159] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.106164] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI] [ 0.106169] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM [ 0.106218] acpi PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored) [ 0.106221] acpi PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored) [ 0.106223] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) [ 0.106226] acpi PNP0A03:00: host bridge window [mem 0xe0000000-0xffdfffff] (ignored) [ 0.106228] PCI: root bus 00: using default resources [ 0.106231] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. [ 0.106359] PCI host bridge to bus 0000:00 [ 0.106362] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.106365] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.106367] pcibus 0000:00: root bus resource [mem 0x00000000-0x7fffffffff] [ 0.106396] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 [ 0.106731] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100 [ 0.107168] pci 0000:00:01.1: [8086:7111] type 00 class 0x01018a [ 0.107433] pci 0000:00:01.1: reg 0x20: [io 0xd000-0xd00f] [ 0.107607] pci 0000:00:02.0: [80ee:beef] type 00 class 0x030000 [ 0.112244] pci 0000:00:02.0: reg 0x10: [mem 0xe0000000-0xe0ffffff pref] [ 0.141067] pci 0000:00:03.0: [8086:100e] type 00 class 0x020000 [ 0.145564] pci 0000:00:03.0: reg 0x10: [mem 0xf0000000-0xf001ffff] [ 0.157102] pci 0000:00:03.0: reg 0x18: [io 0xd010-0xd017] [ 0.176899] pci 0000:00:04.0: [80ee:cafe] type 00 class 0x088000 [ 0.180529] pci 0000:00:04.0: reg 0x10: [io 0xd020-0xd03f] [ 0.185836] pci 0000:00:04.0: reg 0x14: [mem 0xf0400000-0xf07fffff] [ 0.188666] pci 0000:00:04.0: reg 0x18: [mem 0xf0800000-0xf0803fff pref] [ 0.208555] pci 0000:00:05.0: [8086:2415] type 00 class 0x040100 [ 0.208627] pci 0000:00:05.0: reg 0x10: [io 0xd100-0xd1ff] [ 0.208675] pci 0000:00:05.0: reg 0x14: [io 0xd200-0xd23f] [ 0.209043] pci 0000:00:06.0: [106b:003f] type 00 class 0x0c0310 [ 0.212767] pci 0000:00:06.0: reg 0x10: [mem 0xf0804000-0xf0804fff] [ 0.240692] pci 0000:00:07.0: [8086:7113] type 00 class 0x068000 [ 0.241223] pci 0000:00:08.0: [8086:100e] type 00 class 0x020000 [ 0.248588] pci 0000:00:08.0: reg 0x10: [mem 0xf0820000-0xf083ffff] [ 0.257178] pci 0000:00:08.0: reg 0x18: [io 0xd240-0xd247] [ 0.276246] pci 0000:00:0b.0: [8086:265c] type 00 class 0x0c0320 [ 0.277937] pci 0000:00:0b.0: reg 0x10: [mem 0xf0840000-0xf0840fff] [ 0.306737] pci 0000:00:0d.0: [8086:2829] type 00 class 0x010601 [ 0.310903] pci 0000:00:0d.0: reg 0x10: [io 0xd248-0xd24f] [ 0.320055] pci 0000:00:0d.0: reg 0x18: [io 0xd258-0xd25f] [ 0.330294] pci 0000:00:0d.0: reg 0x20: [io 0xd270-0xd27f] [ 0.334824] pci 0000:00:0d.0: reg 0x24: [mem 0xf0842000-0xf0843fff] [ 0.340870] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 9 10 11) [ 0.341024] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 9 10 11) [ 0.341079] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 9 10 11) [ 0.341135] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 9 10 11) [ 0.341222] ACPI: Enabled 1 GPEs in block 00 to 07 [ 0.341228] ACPI: _SB.PCI0: notify handler is installed [ 0.341237] Found 1 acpi root devices [ 0.344018] vgaarb: setting as boot device: PCI:0000:00:02.0 [ 0.344021] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 0.344024] vgaarb: loaded [ 0.344027] vgaarb: bridge control possible 0000:00:02.0 [ 0.344147] SCSI subsystem initialized [ 0.344228] libata version 3.00 loaded. [ 0.344228] ACPI: bus type USB registered [ 0.344228] usbcore: registered new interface driver usbfs [ 0.344228] usbcore: registered new interface driver hub [ 0.344228] usbcore: registered new device driver usb [ 0.344228] PCI: Using ACPI for IRQ routing [ 0.344228] PCI: pci_cache_line_size set to 64 bytes [ 0.344228] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff] [ 0.344228] e820: reserve RAM buffer [mem 0xdfff0000-0xdfffffff] [ 0.344228] e820: reserve RAM buffer [mem 0x2e4600000-0x2e7ffffff] [ 0.344271] NetLabel: Initializing [ 0.344273] NetLabel: domain hash size = 128 [ 0.344275] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.344286] NetLabel: unlabeled traffic allowed by default [ 0.344321] Switched to clocksource refined-jiffies [ 0.349959] AppArmor: AppArmor Filesystem Enabled [ 0.349973] pnp: PnP ACPI init [ 0.349980] ACPI: bus type PNP registered [ 0.350034] pnp 00:00: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.350042] pnp 00:01: [dma 4] [ 0.350053] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.350108] pnp 00:02: Plug and Play ACPI device, IDs PNP0f03 (active) [ 0.350140] pnp 00:03: Plug and Play ACPI device, IDs PNP0400 (active) [ 0.350433] pnp: PnP ACPI: found 4 devices [ 0.350435] ACPI: bus type PNP unregistered [ 0.361291] Switched to clocksource acpi_pm [ 0.361300] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 0.361303] pci_bus 0000:00: resource 5 [mem 0x00000000-0x7fffffffff] [ 0.361324] NET: Registered protocol family 2 [ 0.361487] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.361826] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.361921] TCP: Hash tables configured (established 131072 bind 65536) [ 0.361933] TCP: reno registered [ 0.361947] UDP hash table entries: 8192 (order: 6, 262144 bytes) [ 0.361983] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes) [ 0.362038] NET: Registered protocol family 1 [ 0.362045] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 0.362065] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 0.362086] pci 0000:00:02.0: Video device with shadowed ROM [ 0.363519] PCI: CLS 0 bytes, default 64 [ 0.363578] Trying to unpack rootfs image as initramfs... [ 0.569939] Freeing initrd memory: 20468K (ffff8800357f6000 - ffff880036bf3000) [ 0.569946] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.569949] software IO TLB [mem 0xdbff0000-0xdfff0000] (64MB) mapped at [ffff8800dbff0000-ffff8800dffeffff] [ 0.570160] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.570335] microcode: CPU0 sig=0x306c3, pf=0x2, revision=0x19 [ 0.570382] microcode: CPU1 sig=0x306c3, pf=0x2, revision=0x19 [ 0.570388] microcode: CPU2 sig=0x306c3, pf=0x2, revision=0x19 [ 0.570536] microcode: Microcode Update Driver: v2.00 tigran@aivazian.fsnet.co.uk, Peter Oruba [ 0.570539] Scanning for low memory corruption every 60 seconds [ 0.570764] Initialise system trusted keyring [ 0.570793] audit: initializing netlink socket (disabled) [ 0.570802] type=2000 audit(1490791862.567:1): initialized [ 0.588414] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.589576] zbud: loaded [ 0.589848] VFS: Disk quotas dquot_6.5.2 [ 0.589875] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.590450] fuse init (API version 7.22) [ 0.590619] msgmni has been set to 22148 [ 0.590666] Key type big_key registered [ 0.593213] Key type asymmetric registered [ 0.593216] Asymmetric key parser 'x509' registered [ 0.593245] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.593402] io scheduler noop registered [ 0.593406] io scheduler deadline registered (default) [ 0.593428] io scheduler cfq registered [ 0.593475] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.593483] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.593509] vesafb: mode is 640x480x32, linelength=2560, pages=0 [ 0.593511] vesafb: scrolling: redraw [ 0.593514] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [ 0.593519] mtrr: your processor doesn't support write-combining [ 0.593577] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90001b80000, using 1216k, total 1216k [ 0.594767] Console: switching to colour frame buffer device 80x30 [ 0.595191] fb0: VESA VGA frame buffer device [ 0.595203] intel_idle: does not run on family 6 model 60 [ 0.595210] ipmi message handler version 39.2 [ 0.595260] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.595305] ACPI: AC Adapter [AC] (on-line) [ 0.595366] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.595371] ACPI: Power Button [PWRF] [ 0.595414] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input1 [ 0.595417] ACPI: Sleep Button [SLPF] [ 0.595568] GHES: HEST is not enabled! [ 0.595669] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.599264] Linux agpgart interface v0.103 [ 0.601477] brd: module loaded [ 0.602614] loop: module loaded [ 0.602715] ata_piix 0000:00:01.1: version 2.13 [ 0.603270] scsi0 : ata_piix [ 0.603449] scsi1 : ata_piix [ 0.603470] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xd000 irq 14 [ 0.603473] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xd008 irq 15 [ 0.603646] libphy: Fixed MDIO Bus: probed [ 0.603696] tun: Universal TUN/TAP device driver, 1.6 [ 0.603698] tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com [ 0.603807] PPP generic driver version 2.4.2 [ 0.603910] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.603915] ehci-pci: EHCI PCI platform driver [ 0.604380] ehci-pci 0000:00:0b.0: EHCI Host Controller [ 0.604386] ehci-pci 0000:00:0b.0: new USB bus registered, assigned bus number 1 [ 0.604520] ehci-pci 0000:00:0b.0: irq 19, io mem 0xf0840000 [ 0.616083] ehci-pci 0000:00:0b.0: USB 2.0 started, EHCI 1.00 [ 0.616133] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.616136] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.616139] usb usb1: Product: EHCI Host Controller [ 0.616142] usb usb1: Manufacturer: Linux 3.13.0-112-generic ehci_hcd [ 0.616144] usb usb1: SerialNumber: 0000:00:0b.0 [ 0.616801] hub 1-0:1.0: USB hub found [ 0.616809] hub 1-0:1.0: 8 ports detected [ 0.616937] ehci-platform: EHCI generic platform driver [ 0.616944] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.616946] ohci-pci: OHCI PCI platform driver [ 0.617298] ohci-pci 0000:00:06.0: OHCI PCI host controller [ 0.617303] ohci-pci 0000:00:06.0: new USB bus registered, assigned bus number 2 [ 0.617344] ohci-pci 0000:00:06.0: irq 22, io mem 0xf0804000 [ 0.672410] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.672414] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.672417] usb usb2: Product: OHCI PCI host controller [ 0.672420] usb usb2: Manufacturer: Linux 3.13.0-112-generic ohci_hcd [ 0.672422] usb usb2: SerialNumber: 0000:00:06.0 [ 0.672721] hub 2-0:1.0: USB hub found [ 0.672735] hub 2-0:1.0: 8 ports detected [ 0.672933] ohci-platform: OHCI generic platform driver [ 0.672942] uhci_hcd: USB Universal Host Controller Interface driver [ 0.672984] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 0.673722] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.673730] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.674110] mousedev: PS/2 mouse device common for all mice [ 0.675867] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 0.676072] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram [ 0.676098] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2 [ 0.676119] device-mapper: uevent: version 1.0.3 [ 0.676267] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com [ 0.676273] ledtrig-cpu: registered to indicate activity on CPUs [ 0.676413] TCP: cubic registered [ 0.676471] NET: Registered protocol family 10 [ 0.676585] NET: Registered protocol family 17 [ 0.676593] Key type dns_resolver registered [ 0.677205] Loading compiled-in X.509 certificates [ 0.677702] Loaded X.509 cert 'Magrathea: Glacier signing key: f50a65a6eee1644cbc1c2ef17b37cf4f6d2b2119' [ 0.677714] registered taskstats version 1 [ 0.680499] Key type trusted registered [ 0.684673] Key type encrypted registered [ 0.684677] AppArmor: AppArmor sha1 policy hashing enabled [ 0.684680] IMA: No TPM chip found, activating TPM-bypass! [ 0.684920] regulator-dummy: disabling [ 0.685209] Magic number: 9:771:886 [ 0.685331] rtc_cmos rtc_cmos: setting system clock to 2017-03-29 12:51:03 UTC (1490791863) [ 0.685535] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.685538] EDD information not available. [ 0.685556] PM: Hibernation image not present or could not be loaded. [ 0.756606] ata1.00: ATAPI: VBOX CD-ROM, 1.0, max UDMA/133 [ 0.757089] ata1.00: configured for UDMA/33 [ 0.757693] scsi 0:0:0:0: CD-ROM VBOX CD-ROM 1.0 PQ: 0 ANSI: 5 [ 0.758474] sr0: scsi3-mmc drive: 32x/32x xa/form2 tray [ 0.758477] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 0.758692] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 0.758801] sr 0:0:0:0: Attached scsi generic sg0 type 5 [ 0.760772] Freeing unused kernel memory: 1340K (ffffffff81d20000 - ffffffff81e6f000) [ 0.760775] Write protecting the kernel read-only data: 12288k [ 0.761205] Freeing unused kernel memory: 748K (ffff880001745000 - ffff880001800000) [ 0.762152] Freeing unused kernel memory: 672K (ffff880001b58000 - ffff880001c00000) [ 0.774278] systemd-udevd[112]: starting version 204 [ 0.786043] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 0.786046] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.080133] usb 2-1: new full-speed USB device number 2 using ohci-pci [ 1.099516] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input4 [ 1.131823] e1000 0000:00:03.0 eth0: (PCI:33MHz:32-bit) 08:00:27:ee:48:59 [ 1.131831] e1000 0000:00:03.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.333098] usb 2-1: New USB device found, idVendor=80ee, idProduct=0021 [ 1.333102] usb 2-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0 [ 1.333105] usb 2-1: Product: USB Tablet [ 1.333108] usb 2-1: Manufacturer: VirtualBox [ 1.338436] hidraw: raw HID events driver (C) Jiri Kosina [ 1.347231] usbcore: registered new interface driver usbhid [ 1.347235] usbhid: USB HID core driver [ 1.351248] input: VirtualBox USB Tablet as /devices/pci0000:00/0000:00:06.0/usb2/2-1/2-1:1.0/input/input5 [ 1.351623] hid-generic 0003:80EE:0021.0001: input,hidraw0: USB HID v1.10 Mouse [VirtualBox USB Tablet] on usb-0000:00:06.0-1/input0 [ 1.480089] e1000 0000:00:08.0 eth1: (PCI:33MHz:32-bit) 08:00:27:e3:7c:d9 [ 1.480094] e1000 0000:00:08.0 eth1: Intel(R) PRO/1000 Network Connection [ 1.480172] ahci 0000:00:0d.0: version 3.0 [ 1.480666] ahci 0000:00:0d.0: SSS flag set, parallel bus scan disabled [ 1.480757] ahci 0000:00:0d.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode [ 1.480761] ahci 0000:00:0d.0: flags: 64bit ncq stag only ccc [ 1.481121] scsi2 : ahci [ 1.481157] ata3: SATA max UDMA/133 abar m8192@0xf0842000 port 0xf0842100 irq 21 [ 1.569291] tsc: Refined TSC clocksource calibration: 3555.917 MHz [ 1.800196] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.800358] ata3.00: ATA-6: VBOX HARDDISK, 1.0, max UDMA/133 [ 1.800362] ata3.00: 734003200 sectors, multi 128: LBA48 NCQ (depth 31/32) [ 1.800622] ata3.00: configured for UDMA/133 [ 1.800914] scsi 2:0:0:0: Direct-Access ATA VBOX HARDDISK 1.0 PQ: 0 ANSI: 5 [ 1.801138] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 1.801163] sd 2:0:0:0: [sda] 734003200 512-byte logical blocks: (375 GB/350 GiB) [ 1.801482] sd 2:0:0:0: [sda] Write Protect is off [ 1.801486] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.801662] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.832075] sda: sda1 sda2 < sda5 > [ 1.833099] sd 2:0:0:0: [sda] Attached SCSI disk [ 1.903358] random: lvm urandom read with 27 bits of entropy available [ 1.922574] bio: create slab at 1 [ 2.084001] EXT4-fs (dm-0): INFO: recovery required on readonly filesystem [ 2.084043] EXT4-fs (dm-0): write access will be enabled during recovery [ 2.568848] Switched to clocksource tsc [ 2.588619] random: nonblocking pool is initialized [ 3.191283] EXT4-fs (dm-0): orphan cleanup on readonly fs [ 3.191737] EXT4-fs (dm-0): 17 orphan inodes deleted [ 3.191740] EXT4-fs (dm-0): recovery complete [ 3.249076] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 4.496389] init: plymouth-upstart-bridge main process (191) terminated with status 1 [ 4.496399] init: plymouth-upstart-bridge main process ended, respawning [ 4.499635] init: plymouth-upstart-bridge main process (202) terminated with status 1 [ 4.499644] init: plymouth-upstart-bridge main process ended, respawning [ 4.501741] init: plymouth-upstart-bridge main process (204) terminated with status 1 [ 4.501750] init: plymouth-upstart-bridge main process ended, respawning [ 4.504757] init: plymouth-upstart-bridge main process (205) terminated with status 1 [ 4.504766] init: plymouth-upstart-bridge main process ended, respawning [ 4.509329] init: plymouth-upstart-bridge main process (207) terminated with status 1 [ 4.509337] init: plymouth-upstart-bridge main process ended, respawning [ 17.446370] Adding 11608060k swap on /dev/mapper/kor1030612--vg-swap_1. Priority:-1 extents:1 across:11608060k FS [ 17.607229] systemd-udevd[314]: starting version 204 [ 17.751481] parport_pc 00:03: reported by Plug and Play ACPI [ 17.757713] [drm] Initialized drm 1.1.0 20060810 [ 17.757940] vboxvideo: module verification failed: signature and/or required key missing - tainting kernel [ 17.758764] [drm] Initialized vboxvideo 1.0.0 20090303 for 0000:00:02.0 on minor 0 [ 17.759420] lp: driver loaded but no devices found [ 17.765450] input: Unspecified device as /devices/pci0000:00/0000:00:04.0/input/input6 [ 17.765884] vboxguest: major 0, IRQ 20, I/O port d020, MMIO at 00000000f0400000 (size 0x400000) [ 17.765888] vboxguest: Successfully loaded version 4.3.20 (interface 0x00010004) [ 17.768818] device-mapper: multipath: version 1.6.0 loaded [ 17.769012] ppdev: user-space parallel port driver [ 17.778547] piix4_smbus 0000:00:07.0: SMBus base address uninitialized - upgrade BIOS or use force_addr=0xaddr [ 18.097441] type=1400 audit(1490791880.909:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=451 comm="apparmor_parser" [ 18.097448] type=1400 audit(1490791880.909:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=451 comm="apparmor_parser" [ 18.097452] type=1400 audit(1490791880.909:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=451 comm="apparmor_parser" [ 18.097459] type=1400 audit(1490791880.909:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=453 comm="apparmor_parser" [ 18.097465] type=1400 audit(1490791880.909:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=453 comm="apparmor_parser" [ 18.097469] type=1400 audit(1490791880.909:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=453 comm="apparmor_parser" [ 18.098022] type=1400 audit(1490791880.909:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=452 comm="apparmor_parser" [ 18.098028] type=1400 audit(1490791880.909:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=452 comm="apparmor_parser" [ 18.098032] type=1400 audit(1490791880.909:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=452 comm="apparmor_parser" [ 18.256094] intel8x0_measure_ac97_clock: measured 55614 usecs (8472 samples) [ 18.256098] intel8x0: measured clock 152335 rejected [ 18.427695] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 18.616192] intel8x0_measure_ac97_clock: measured 56048 usecs (7200 samples) [ 18.616196] intel8x0: measured clock 128461 rejected [ 18.976193] intel8x0_measure_ac97_clock: measured 56050 usecs (7200 samples) [ 18.976197] intel8x0: measured clock 128456 rejected [ 18.976199] intel8x0: clocking to 48000 [ 20.531273] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 20.579842] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null) [ 25.352494] init: failsafe main process (682) killed by TERM signal [ 25.672522] Bluetooth: Core ver 2.17 [ 25.672535] NET: Registered protocol family 31 [ 25.672538] Bluetooth: HCI device and connection manager initialized [ 25.672545] Bluetooth: HCI socket layer initialized [ 25.672548] Bluetooth: L2CAP socket layer initialized [ 25.672551] Bluetooth: SCO socket layer initialized [ 25.676548] Bluetooth: RFCOMM TTY layer initialized [ 25.676557] Bluetooth: RFCOMM socket layer initialized [ 25.676562] Bluetooth: RFCOMM ver 1.11 [ 25.681382] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 25.681386] Bluetooth: BNEP filters: protocol multicast [ 25.681394] Bluetooth: BNEP socket layer initialized [ 25.688795] type=1400 audit(1490791888.501:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=818 comm="apparmor_parser" [ 25.688802] type=1400 audit(1490791888.501:12): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=818 comm="apparmor_parser" [ 25.903583] init: cups main process (819) killed by HUP signal [ 25.903594] init: cups main process ended, respawning [ 26.354625] init: plymouth-upstart-bridge main process ended, respawning [ 26.354807] init: plymouth main process (208) killed by ABRT signal [ 26.587061] type=1400 audit(1490791889.397:13): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=911 comm="apparmor_parser" [ 26.587068] type=1400 audit(1490791889.397:14): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=911 comm="apparmor_parser" [ 26.587072] type=1400 audit(1490791889.397:15): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=911 comm="apparmor_parser" [ 26.587339] type=1400 audit(1490791889.397:16): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=910 comm="apparmor_parser" [ 26.587345] type=1400 audit(1490791889.397:17): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chromium" pid=910 comm="apparmor_parser" [ 26.589181] type=1400 audit(1490791889.401:18): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=915 comm="apparmor_parser" [ 26.590538] type=1400 audit(1490791889.401:19): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/telepathy/mission-control-5" pid=914 comm="apparmor_parser" [ 26.590543] type=1400 audit(1490791889.401:20): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/telepathy/telepathy-*" pid=914 comm="apparmor_parser" [ 28.126768] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX [ 28.145587] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 28.148590] e1000: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX [ 28.148856] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 28.581551] vboxdrv: Found 3 processor cores. [ 28.583242] vboxdrv: fAsync=0 offMin=0x18b3 offMax=0x14fd3a [ 28.583383] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. [ 28.583385] vboxdrv: Successfully loaded version 4.3.10_Ubuntu (interface 0x001a0007). [ 28.595737] vboxpci: IOMMU not found (not registered) [ 28.701183] vboxsf: Successfully loaded version 4.3.20 (interface 0x00010004) [ 29.105973] init: samba-ad-dc main process (1267) terminated with status 1 [ 29.147356] symap_custom_3_13_0_112_generic_x86_64: module license 'Proprietary' taints kernel. [ 29.147360] Disabling lock debugging due to kernel taint [ 55.890461] audit_printk_skb: 39 callbacks suppressed [ 55.890465] type=1400 audit(1490791918.702:34): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=3293 comm="apparmor_parser" [ 55.890471] type=1400 audit(1490791918.702:35): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=3293 comm="apparmor_parser" [61767.032538] WARNING! power/level is deprecated; use power/control instead [61771.636513] rtvscand: The scan_unevictable_pages sysctl/node-interface has been disabled for lack of a legitimate use case. If you have one, please send an email to linux-mm@kvack.org. [62838.013387] e1000: eth1 NIC Link is Down [62844.024468] e1000: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX [75669.666376] dca service started, version 1.12.1 [75676.316711] pps_core: LinuxPPS API ver. 1 registered [75676.316715] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [75676.321414] PTP clock support registered [75683.318369] Intel(R) Gigabit Ethernet Network Driver - version 5.3.2_AVB [75683.318375] Copyright (c) 2007-2015 Intel Corporation.

[iamdharm20]

followed steps : unloaded all the driver. then loaded all the drivers

[pinealservo]

It looks like you're running in a virtual machine? I guess the avb i210 driver is loading because the virtualized e1000 is similar enough to the i210 to make it happy, but I wouldn't expect it to actually work in that situation.

Running this stuff from inside VirtualBox is not supported. If you've got an i210 installed in the host machine, try running from the host Linux environment. If the host environment is not Linux, I don't think we have anything that will work for you.

[christopher-s-hall]

Good catch @pinealservo. The only way this might work is directly assigning the HW device (I210) to the VM. I don't know if that's possible with your configuration/VMM. There could also be performance issues with TSC virtualization. That depends upon the VM configuration.

As noted above, VMs are not supported at this time.