No matching manifest for linux/arm/v7

[Terrence77]

Azure IoT Edge LoRaWAN Starter Kit

I have installing AzureIotEdge to my Raspberry Pi with the Seeed Stuio Wm1002 lora concentrator.

I noticed in My IOTHub / Devices / MyGateway that LoRaWanNetworkSrvModule and LoRaBasicsStationModule were showing a runtime status as Error.

I went to my gateway and issued this command to look at the logs and found this error.

sudo iotedge system logs

2024-01-17T01:50:03Z [WARN] - Could not pull image loraedge/lorabasicsstationmodule:2.2.2 2024-01-17T01:50:03Z [WARN] - caused by: no matching manifest for linux/arm/v7 in the manifest list entries

No manifest for linux/arm/v7 ?? Doing research I noticed on this website that the linux/arm/v7 2.2.2 file does exist. https://hub.docker.com/r/loraedge/lorabasicsstationmodule/tags

Ideas on solving this issue?

Thank you.

[Terrence77]

I know this probably is not the place for tech support, but I have searched the net and can't find any forum answering questions about this great project.

Suggestions?

[kbeaugrand]

@Terrence77, is this a transient error ?

As far I know by looking in the manifest, there is a tag for linux/arm/v7:

Otherwise, you can manually specify to download the required image for testing purpose: loraedge/lorabasicsstationmodule:2.2.2-arm32v7

[Terrence77]

@kbeaugrand Thank you for your reply.

Yes, that is what I was trying to get across in my post, that the file DOES exist.

Doing research I noticed on this website that the linux/arm/v7 2.2.2 file does exist. https://hub.docker.com/r/loraedge/lorabasicsstationmodule/tags

is this a transient error

Well I am seeing the error in the Azure portal.

Otherwise, you can manually specify to download the required image for testing purpose: loraedge/lorabasicsstationmodule:2.2.2-arm32v7

I "think" I tried that but was not successful.

I am new to containers so I am sure I mangled my syntax.

[Terrence77]

@kbeaugrand

Otherwise, you can manually specify to download the required image for testing purpose: loraedge/lorabasicsstationmodule:2.2.2-arm32v7

Can I specify this in the Azure Portal, or do I need to do it in Bash on the gateway?

Thanks.

[kbeaugrand]

@kbeaugrand

Otherwise, you can manually specify to download the required image for testing purpose: loraedge/lorabasicsstationmodule:2.2.2-arm32v7

Can I specify this in the Azure Portal, or do I need to do it in Bash on the gateway?

Thanks.

Please share us the configuration you are using in the portal for the module.

[Terrence77]

Thank you for your continued support on my issue. I am very excited to get this working for my Lora IOT network.

I have been following these instructions. https://azure.github.io/iotedge-lorawan-starterkit/dev/quickstart/

Here is the hardware config and setup.

`Rasp Pi 2B Pi OS Lite 32bit Debian Bulllseye Seeed WM1302

sudo raspi-config Endable SPI interface Endable IC2 interface

sudo apt update sudo apt install -y git cd ~ git clone https://github.com/Lora-net/sx1302_hal cd ~/sx1302_hal make

curl https://packages.microsoft.com/config/debian/11/packages-microsoft-prod.deb > ./packages-microsoft-prod.deb sudo apt-get install ./packages-microsoft-prod.deb sudo apt-get update sudo apt-get install moby-engine sudo curl -L https://github.com/Azure/azure-iotedge/releases/download/1.2.5/aziot-identity-service_1.2.4-1_debian11_armhf.deb -o aziot-identity-service.deb && sudo apt-get install ./aziot-identity-service.deb sudo curl -L https://github.com/Azure/azure-iotedge/releases/download/1.2.5/aziot-edge_1.2.5-1_debian11_armhf.deb -o aziot-edge.deb && sudo apt-get install ./aziot-edge.deb

pi@raspberrypi:~ $ sudo iotedge system status System services: aziot-edged Running aziot-identityd Running aziot-keyd Running aziot-certd Running aziot-tpmd Ready `

[Terrence77]

[Terrence77]

The script that ran when I clicked "Deploy to Azure" setup the devices in my IOTHub. I note that one of the devices is a concentrator (my Seeed WM1302?). The device twin shows it being a 1301, NOT a 1302.

[Mandur]

Apologies for not seeing the issue earlier, are you still trying to fix it?

Did you try to run "docker pull loraedge/lorabasicsstationmodule:2.2.2-arm32v7" on your target device?

[Terrence77]

No, I bailed on the project.

[Mandur]

Understood, sorry we did not see the request earlier, have a great weekend!