LiteRadio 3 not saving settings

[GigaJul06]

I recently ordered a Nano TX V2 Module for my LiteRadio 3 ELRS and I cannot get it to work.

When I try to set the radio to external tx module via BetaFPV configurator, it stays in internal tx mode.

The radio is off when connected and yes I properly hit the « save and reboot » button.

I tried to flash the latest firmware to my radio but it changes nothing.

Did I missed something or is my radio broken ?

Thanks for the help !

[JanuszKr]

I have the same problem with LiteRadio 2 Se ELRS upgraded to version 3. Betafpv configurator connects to the right COM port, reads correctly the position of the gimbals and switches, but does not see ELRS nor the options. The Save & reboot button is grayed. When I try to restore the factory settings, everything seems to be alright, the Save and reboot button is ungreyed but it does not work.

[LeehotYuu]

If using ELRS3, it is better to update the firmware to the latest version. LR2 SE V2 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348908057-Lite-Radio-2-SE LR3 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348993177-Lite-Radio-3

The latest firmware has resumed sending data from the LR3 external ELRS3 channel, but modifying the parameters of the external ELRS3 is still not supported on the BETAFPV Configurator. You can only modify the power via buttons and there is no feedback on the results of any changes, which is really bad experience. In fact BETAFPV Configurator setting the parameters of the external ELRS3 has already been implemented, but due to the complex code framework of the LR3 it is currently difficult to add this feature.

[JanuszKr]

The problem is that after flashing elrs 3 Betaflight Configurator did not detect elrs at all and did not allow to save any changes in settings. I had to invert the cables connecting one of the gimbals to obtain the correct roll behavior.

pt., 20 wrz 2024, 10:21 użytkownik LeehotYuu @.***> napisał:

If using ELRS3, it is better to update the firmware to the latest version. LR2 SE V2 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348908057-Lite-Radio-2-SE LR3 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348993177-Lite-Radio-3

The latest firmware has resumed sending data from the LR3 external ELRS3 channel, but modifying the parameters of the external ELRS3 is still not supported on the BETAFPV Configurator. You can only modify the power via buttons and there is no feedback on the results of any changes, which is really bad experience. In fact BETAFPV Configurator setting the parameters of the external ELRS3 has already been implemented, but due to the complex code framework of the LR3 it is currently difficult to add this feature.

— Reply to this email directly, view it on GitHub https://github.com/BETAFPV/BETAFPV_Configurator/issues/53#issuecomment-2363148592, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGEUCURMZFVSQHIRUBTZXPLJHAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNRTGE2DQNJZGI . You are receiving this because you commented.Message ID: @.***>

[LeehotYuu]

The problem is that after flashing elrs 3 Betaflight Configurator did not detect elrs at all and did not allow to save any changes in settings. I had to invert the cables connecting one of the gimbals to obtain the correct roll behavior. pt., 20 wrz 2024, 10:21 użytkownik LeehotYuu @.> napisał: … If using ELRS3, it is better to update the firmware to the latest version. LR2 SE V2 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348908057-Lite-Radio-2-SE LR3 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348993177-Lite-Radio-3 The latest firmware has resumed sending data from the LR3 external ELRS3 channel, but modifying the parameters of the external ELRS3 is still not supported on the BETAFPV Configurator. You can only modify the power via buttons and there is no feedback on the results of any changes, which is really bad experience. In fact BETAFPV Configurator setting the parameters of the external ELRS3 has already been implemented, but due to the complex code framework of the LR3 it is currently difficult to add this feature. — Reply to this email directly, view it on GitHub <#53 (comment)>, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGEUCURMZFVSQHIRUBTZXPLJHAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNRTGE2DQNJZGI . You are receiving this because you commented.Message ID: @.>

I can't get enough information through your description. Was your LR2 SE V2 originally Frsky or ELRS? Version of BETAFPV Configurator? Is it possible to modify the mix control?

If your RC was originally Frsky, the LR2 SE V2 cannot use ELRS3 due to different hardware.

[JanuszKr]

Betafpv Configurator is v. 2.0 RC2 and the motherboard was originally ELRS2. By upgrading through this version of BETAFPV Configurator I made it work as ELRS3 and I can use it as such, except that BetaFPV Conf. does not detect it after connecting. I had to inverse the roll direction of the right gimble by swapping the cables for getting it right.

wt., 24 wrz 2024, 05:15 użytkownik LeehotYuu @.***> napisał:

The problem is that after flashing elrs 3 Betaflight Configurator did not detect elrs at all and did not allow to save any changes in settings. I had to invert the cables connecting one of the gimbals to obtain the correct roll behavior. pt., 20 wrz 2024, 10:21 użytkownik LeehotYuu @.

> napisał: … <#m-66205852389419338> If using ELRS3, it is better to update the firmware to the latest version. LR2 SE V2 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348908057-Lite-Radio-2-SE https://support.betafpv.com/hc/en-us/articles/4414348908057-Lite-Radio-2-SE LR3 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348993177-Lite-Radio-3 https://support.betafpv.com/hc/en-us/articles/4414348993177-Lite-Radio-3 The latest firmware has resumed sending data from the LR3 external ELRS3 channel, but modifying the parameters of the external ELRS3 is still not supported on the BETAFPV Configurator. You can only modify the power via buttons and there is no feedback on the results of any changes, which is really bad experience. In fact BETAFPV Configurator setting the parameters of the external ELRS3 has already been implemented, but due to the complex code framework of the LR3 it is currently difficult to add this feature. — Reply to this email directly, view it on GitHub <#53 (comment) https://github.com/BETAFPV/BETAFPV_Configurator/issues/53#issuecomment-2363148592>, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGEUCURMZFVSQHIRUBTZXPLJHAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNRTGE2DQNJZGI https://github.com/notifications/unsubscribe-auth/A6EAVGEUCURMZFVSQHIRUBTZXPLJHAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNRTGE2DQNJZGI . You are receiving this because you commented.Message ID: @.>

I can't get enough information through your description. Was your LR2 SE V2 originally Frsky or ELRS? Version of BETAFPV Configurator? Is it possible to modify the mix control?

If your RC was originally Frsky, the LR2 SE V2 cannot use ELRS3 due to different hardware.

— Reply to this email directly, view it on GitHub https://github.com/BETAFPV/BETAFPV_Configurator/issues/53#issuecomment-2370027161, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGGL66BKRMJUS64ZPZLZYDKNLAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNZQGAZDOMJWGE . You are receiving this because you commented.Message ID: @.***>

[LeehotYuu]

Betafpv Configurator is v. 2.0 RC2 and the motherboard was originally ELRS2. By upgrading through this version of BETAFPV Configurator I made it work as ELRS3 and I can use it as such, except that BetaFPV Conf. does not detect it after connecting. I had to inverse the roll direction of the right gimble by swapping the cables for getting it right. wt., 24 wrz 2024, 05:15 użytkownik LeehotYuu @.> napisał: … The problem is that after flashing elrs 3 Betaflight Configurator did not detect elrs at all and did not allow to save any changes in settings. I had to invert the cables connecting one of the gimbals to obtain the correct roll behavior. pt., 20 wrz 2024, 10:21 użytkownik LeehotYuu @. > napisał: … <#m-66205852389419338> If using ELRS3, it is better to update the firmware to the latest version. LR2 SE V2 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348908057-Lite-Radio-2-SE https://support.betafpv.com/hc/en-us/articles/4414348908057-Lite-Radio-2-SE LR3 (Frsky/ELRS): https://support.betafpv.com/hc/en-us/articles/4414348993177-Lite-Radio-3 https://support.betafpv.com/hc/en-us/articles/4414348993177-Lite-Radio-3 The latest firmware has resumed sending data from the LR3 external ELRS3 channel, but modifying the parameters of the external ELRS3 is still not supported on the BETAFPV Configurator. You can only modify the power via buttons and there is no feedback on the results of any changes, which is really bad experience. In fact BETAFPV Configurator setting the parameters of the external ELRS3 has already been implemented, but due to the complex code framework of the LR3 it is currently difficult to add this feature. — Reply to this email directly, view it on GitHub <#53 (comment) <#53 (comment)>>, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGEUCURMZFVSQHIRUBTZXPLJHAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNRTGE2DQNJZGI https://github.com/notifications/unsubscribe-auth/A6EAVGEUCURMZFVSQHIRUBTZXPLJHAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNRTGE2DQNJZGI . You are receiving this because you commented.Message ID: @.> I can't get enough information through your description. Was your LR2 SE V2 originally Frsky or ELRS? Version of BETAFPV Configurator? Is it possible to modify the mix control? If your RC was originally Frsky, the LR2 SE V2 cannot use ELRS3 due to different hardware. — Reply to this email directly, view it on GitHub <#53 (comment)>, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGGL66BKRMJUS64ZPZLZYDKNLAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNZQGAZDOMJWGE . You are receiving this because you commented.Message ID: @.>

Is it possible to provide a screenshot after connecting the RC?

[LeehotYuu]

Do you mean you are experiencing the situation in the picture? Recently I've been testing the operation of BETAFPV Configurator in Linux-Ubuntu environment and sometimes it runs fine, but sometimes it looks like the picture. If I unplug the USB cable and reconnect it to the PC, it may recover or it may not, like a roll of the dice. I haven't encountered anything like this with macOS or Windows.

[JanuszKr]

I suppose so, my page is in English and I can't read Chinese. But the picture corresponds to what I get, although I run Windows 11 64bits, and not Linux.

czw., 26 wrz 2024, 09:02 użytkownik LeehotYuu @.***> napisał:

2024-09-26.14-42-16.png (view on web) https://github.com/user-attachments/assets/69bfc0e4-6b83-48cd-b818-db9437a0c351 Do you mean you are experiencing the situation in the picture? Recently I've been testing the operation of BETAFPV Configurator in Linux-Ubuntu environment and sometimes it runs fine, but sometimes it looks like the picture. If I unplug the USB cable and reconnect it to the PC, it may recover or it may not, like a roll of the dice. I haven't encountered anything like this with macOS or Windows.

— Reply to this email directly, view it on GitHub https://github.com/BETAFPV/BETAFPV_Configurator/issues/53#issuecomment-2376094947, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGF2PZYBDNC72PU6D7LZYOWO3AVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNZWGA4TIOJUG4 . You are receiving this because you commented.Message ID: @.***>

[LeehotYuu]

I suppose so, my page is in English and I can't read Chinese. But the picture corresponds to what I get, although I run Windows 11 64bits, and not Linux. czw., 26 wrz 2024, 09:02 użytkownik LeehotYuu @.> napisał: … 2024-09-26.14-42-16.png (view on web) https://github.com/user-attachments/assets/69bfc0e4-6b83-48cd-b818-db9437a0c351 Do you mean you are experiencing the situation in the picture? Recently I've been testing the operation of BETAFPV Configurator in Linux-Ubuntu environment and sometimes it runs fine, but sometimes it looks like the picture. If I unplug the USB cable and reconnect it to the PC, it may recover or it may not, like a roll of the dice. I haven't encountered anything like this with macOS or Windows. — Reply to this email directly, view it on GitHub <#53 (comment)>, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGF2PZYBDNC72PU6D7LZYOWO3AVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNZWGA4TIOJUG4 . You are receiving this because you commented.Message ID: @.>

Sorry, I didn't notice switching languages. Fortunately, it didn't interfere with your judgment. Because of the lack of such experience, I can't tell what happened at the moment, I will do more tests with LR2 SE connecting to BETAFPV Configurator under win11 OS at our company, by the way is your win11 Pro or other version? Thank you very much for the information you provided!

[JanuszKr]

It is win11 home, but I don't think it really matters.

pt., 27 wrz 2024, 10:58 użytkownik LeehotYuu @.***> napisał:

I suppose so, my page is in English and I can't read Chinese. But the picture corresponds to what I get, although I run Windows 11 64bits, and not Linux. czw., 26 wrz 2024, 09:02 użytkownik LeehotYuu @.

> napisał: … <#m7122053114003578814> 2024-09-26.14-42-16.png (view on web) https://github.com/user-attachments/assets/69bfc0e4-6b83-48cd-b818-db9437a0c351 https://github.com/user-attachments/assets/69bfc0e4-6b83-48cd-b818-db9437a0c351 Do you mean you are experiencing the situation in the picture? Recently I've been testing the operation of BETAFPV Configurator in Linux-Ubuntu environment and sometimes it runs fine, but sometimes it looks like the picture. If I unplug the USB cable and reconnect it to the PC, it may recover or it may not, like a roll of the dice. I haven't encountered anything like this with macOS or Windows. — Reply to this email directly, view it on GitHub <#53 (comment) https://github.com/BETAFPV/BETAFPV_Configurator/issues/53#issuecomment-2376094947>, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGF2PZYBDNC72PU6D7LZYOWO3AVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNZWGA4TIOJUG4 https://github.com/notifications/unsubscribe-auth/A6EAVGF2PZYBDNC72PU6D7LZYOWO3AVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNZWGA4TIOJUG4 . You are receiving this because you commented.Message ID: @.>

Sorry, I didn't notice switching languages. Fortunately, it didn't interfere with your judgment. Because of the lack of such experience, I can't tell what happened at the moment, I will do more tests with LR2 SE connecting to BETAFPV Configurator under win11 OS at our company, by the way is your win11 Pro or other version? Thank you very much for the information you provided!

— Reply to this email directly, view it on GitHub https://github.com/BETAFPV/BETAFPV_Configurator/issues/53#issuecomment-2378794271, or unsubscribe https://github.com/notifications/unsubscribe-auth/A6EAVGGVPFB4XR6ER2YP3I3ZYUM4JAVCNFSM6AAAAABMPDQXTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNZYG44TIMRXGE . You are receiving this because you commented.Message ID: @.***>