`Bug` Cant upload tft in version v4.3.12.dev1

[Mauricewillemstein]

TFT Version

v4.3.11

Firmware Version

v4.3.12.dev1

Blueprint Version

v4.3.12.dev1

Panel Model

EU

What is the bug?

When i try to update the tft it wont do it. I have 2 panels and they have the same issue. Tried the blank one and the eu version. When try to update it says nextion not connected, then it reboots and working fine on old version (v4.3.11)

Steps to Reproduce

No response

Your Panel's YAML

No response

ESPHome Logs

[10:21:01][I][app:100]: ESPHome version 2024.9.0-dev compiled on Aug 29 2024, 06:12:12 [10:21:01][I][app:102]: Project esphome.NSPanel_HA_Blueprint version 4.3.12.dev1

[10:21:01][C][wifi:428]: Local MAC: E4:65:B8:1C:11:74 [10:21:01][C][wifi:433]: SSID: [redacted] [10:21:01][C][wifi:436]: IP Address: 192.168.2.22 [10:21:01][C][wifi:440]: BSSID: [redacted]

[10:21:01][C][wifi:443]: Signal strength: -60 dB ▂▄▆█ [10:21:01][C][wifi:447]: Channel: 8 [10:21:01][C][wifi:448]: Subnet: 255.255.255.0 [10:21:01][C][wifi:449]: Gateway: 192.168.2.254 [10:21:01][C][wifi:450]: DNS1: 192.168.2.3 [10:21:01][C][wifi:451]: DNS2: 192.168.2.62

[10:21:01][C][logger:186]: Level: DEBUG [10:21:01][C][logger:188]: Log Baud Rate: 0 [10:21:01][C][logger:189]: Hardware UART: UART0 [10:21:01][C][uart.idf:159]: UART Bus 0: [10:21:01][C][uart.idf:160]: TX Pin: GPIO16 [10:21:01][C][uart.idf:161]: RX Pin: GPIO17 [10:21:01][C][uart.idf:163]: RX Buffer Size: 256 [10:21:01][C][uart.idf:165]: Baud Rate: 115200 baud [10:21:01][C][uart.idf:166]: Data Bits: 8 [10:21:01][C][uart.idf:167]: Parity: NONE [10:21:01][C][uart.idf:168]: Stop bits: 1 [10:21:01][C][ledc.output:180]: LEDC Output: [10:21:01][C][ledc.output:181]: Pin GPIO21 [10:21:01][C][ledc.output:182]: LEDC Channel: 0 [10:21:01][C][ledc.output:183]: PWM Frequency: 1319.0 Hz [10:21:01][C][ledc.output:184]: Phase angle: 0.0° [10:21:01][C][ledc.output:185]: Bit depth: 15 [10:21:01][C][template.binary_sensor:028]: Template Binary Sensor 'Nextion display' [10:21:01][C][template.binary_sensor:028]: Device Class: 'connectivity' [10:21:01][C][template.number:050]: Template Number 'Display Brightness' [10:21:01][C][template.number:050]: Unit of Measurement: '%' [10:21:01][C][template.number:051]: Optimistic: YES [10:21:01][C][template.number:052]: Update Interval: 60.0s [10:21:01][C][template.number:050]: Template Number 'Display Brightness Dimdown' [10:21:01][C][template.number:050]: Unit of Measurement: '%' [10:21:01][C][template.number:051]: Optimistic: YES [10:21:01][C][template.number:052]: Update Interval: 60.0s [10:21:01][C][template.number:050]: Template Number 'Display Brightness Sleep' [10:21:01][C][template.number:050]: Unit of Measurement: '%' [10:21:01][C][template.number:051]: Optimistic: YES [10:21:01][C][template.number:052]: Update Interval: 60.0s [10:21:01][C][template.number:050]: Template Number 'Temperature Correction' [10:21:01][C][template.number:050]: Unit of Measurement: '°C' [10:21:01][C][template.number:051]: Optimistic: YES [10:21:01][C][template.number:052]: Update Interval: 60.0s [10:21:01][C][template.number:050]: Template Number 'Timeout Page'

[10:21:01][C][template.number:050]: Unit of Measurement: 's' [10:21:01][C][template.number:051]: Optimistic: YES [10:21:01][C][template.number:052]: Update Interval: 60.0s [10:21:01][C][template.number:050]: Template Number 'Timeout Dimming'

[10:21:01][C][template.number:050]: Unit of Measurement: 's' [10:21:01][C][template.number:051]: Optimistic: YES [10:21:01][C][template.number:052]: Update Interval: 60.0s [10:21:01][C][template.number:050]: Template Number 'Timeout Sleep'

[10:21:01][C][template.number:050]: Unit of Measurement: 's' [10:21:01][C][template.number:051]: Optimistic: YES [10:21:01][C][template.number:052]: Update Interval: 60.0s [10:21:01][C][template.select:065]: Template Select 'Baud rate'

[10:21:01][C][template.select:066]: Update Interval: 60.0s [10:21:01][C][template.select:069]: Optimistic: YES [10:21:01][C][template.select:070]: Initial Option: 115200 [10:21:01][C][template.select:071]: Restore Value: YES [10:21:01][C][template.select:065]: Template Select 'Wake-up page'

[10:21:01][C][template.select:066]: Update Interval: 60.0s [10:21:01][C][template.select:069]: Optimistic: YES [10:21:01][C][template.select:070]: Initial Option: home [10:21:01][C][template.select:071]: Restore Value: YES [10:21:01][C][template.select:065]: Template Select 'Update TFT display - Model'

[10:21:01][C][template.select:066]: Update Interval: 60.0s [10:21:01][C][uptime.sensor:033]: Uptime Sensor 'Uptime seconds' [10:21:01][C][uptime.sensor:033]: Device Class: 'duration' [10:21:01][C][uptime.sensor:033]: State Class: 'total_increasing' [10:21:01][C][uptime.sensor:033]: Unit of Measurement: 's' [10:21:01][C][uptime.sensor:033]: Accuracy Decimals: 0

[10:21:01][C][uptime.sensor:034]: Type: Seconds [10:21:01][C][template.sensor:022]: Template Sensor 'API uptime' [10:21:01][C][template.sensor:022]: Device Class: 'timestamp' [10:21:01][C][template.sensor:022]: State Class: '' [10:21:01][C][template.sensor:022]: Unit of Measurement: '' [10:21:01][C][template.sensor:022]: Accuracy Decimals: 0 [10:21:01][C][template.sensor:023]: Update Interval: never [10:21:01][C][template.sensor:022]: Template Sensor 'Device uptime' [10:21:01][C][template.sensor:022]: Device Class: 'timestamp' [10:21:01][C][template.sensor:022]: State Class: '' [10:21:01][C][template.sensor:022]: Unit of Measurement: '' [10:21:01][C][template.sensor:022]: Accuracy Decimals: 0 [10:21:01][C][template.sensor:023]: Update Interval: never [10:21:01][C][switch.gpio:068]: GPIO Switch 'Nextion display - Power' [10:21:01][C][switch.gpio:091]: Restore Mode: always ON [10:21:01][C][switch.gpio:031]: Pin: GPIO4 [10:21:01][C][template.text_sensor:020]: Template Sensor 'Device Name'

[10:21:01][C][template.text_sensor:020]: Template Sensor 'Detailed Entity'

[10:21:01][C][template.text_sensor:020]: Template Sensor 'Notification Label' [10:21:01][C][template.text_sensor:020]: Template Sensor 'Notification Text' [10:21:02][C][template.text_sensor:020]: Template Sensor 'Version Blueprint'

[10:21:02][C][template.text_sensor:020]: Template Sensor 'Version ESPHome'

[10:21:02][C][template.sensor:022]: Template Sensor 'Blueprint' [10:21:02][C][template.sensor:022]: State Class: '' [10:21:02][C][template.sensor:022]: Unit of Measurement: '%' [10:21:02][C][template.sensor:022]: Accuracy Decimals: 1

[10:21:02][C][template.sensor:023]: Update Interval: 60.0s [10:21:02][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'Left Button' [10:21:02][C][gpio.binary_sensor:016]: Pin: GPIO14 [10:21:02][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'Right Button' [10:21:02][C][gpio.binary_sensor:016]: Pin: GPIO27 [10:21:02][C][switch.gpio:068]: GPIO Switch 'Relay 1' [10:21:02][C][switch.gpio:091]: Restore Mode: restore defaults to OFF [10:21:02][C][switch.gpio:031]: Pin: GPIO22 [10:21:02][C][switch.gpio:068]: GPIO Switch 'Relay 2' [10:21:02][C][switch.gpio:091]: Restore Mode: restore defaults to OFF [10:21:02][C][switch.gpio:031]: Pin: GPIO19 [10:21:02][C][template.switch:068]: Template Switch 'Notification unread' [10:21:02][C][template.switch:091]: Restore Mode: always OFF [10:21:02][C][template.switch:057]: Optimistic: YES [10:21:02][C][template.switch:068]: Template Switch 'Notification sound' [10:21:02][C][template.switch:091]: Restore Mode: restore defaults to OFF [10:21:02][C][template.switch:057]: Optimistic: YES [10:21:02][C][template.switch:068]: Template Switch 'Update TFT automatically'

[10:21:02][C][template.switch:091]: Restore Mode: restore defaults to OFF [10:21:02][C][template.switch:057]: Optimistic: YES

[10:21:02][C][psram:021]: Available: YES [10:21:02][C][psram:024]: Size: 2035 KB

[10:21:02][C][nextion:129]: Device Model: NX4832F035_011C [10:21:02][C][nextion:130]: Firmware Version: 72 [10:21:02][C][nextion:131]: Serial Number: CCB33401746EE755 [10:21:02][C][nextion:132]: Flash Size: 16777216 [10:21:02][C][nextion:133]: Wake On Touch: YES [10:21:02][C][nextion:134]: Exit reparse: YES [10:21:02][D][sensor:094]: 'Uptime seconds': Sending state 398.54800 s with 0 decimals of accuracy [10:21:02][C][factory_reset.button:011]: Factory Reset Button 'Factory reset'

[10:21:02][C][homeassistant.time:010]: Home Assistant Time:

[10:21:03][C][esp32_ble:391]: ESP32 BLE: [10:21:03][C][esp32_ble:393]: MAC address: E4:65:B8:1C:11:76 [10:21:03][C][esp32_ble:394]: IO Capability: none [10:21:03][C][esp32_ble_tracker:653]: BLE Tracker: [10:21:03][C][esp32_ble_tracker:654]: Scan Duration: 300 s [10:21:03][C][esp32_ble_tracker:655]: Scan Interval: 320.0 ms [10:21:03][C][esp32_ble_tracker:656]: Scan Window: 30.0 ms [10:21:03][C][esp32_ble_tracker:657]: Scan Type: ACTIVE [10:21:03][C][esp32_ble_tracker:658]: Continuous Scanning: True [10:21:03][C][captive_portal:089]: Captive Portal: [10:21:03][C][web_server:145]: Web Server: [10:21:03][C][web_server:146]: Address: zolder.local:80

[10:21:03][C][mdns:117]: Hostname: zolder [10:21:03][C][esphome.ota:073]: Over-The-Air updates: [10:21:03][C][esphome.ota:074]: Address: zolder.local:3232 [10:21:03][C][wifi_signal.sensor:010]: WiFi Signal 'RSSI' [10:21:04][D][text_sensor:064]: 'Device Name': Sending state 'zolder' [10:21:11][D][sensor:094]: 'ntc_source': Sending state 1.34050 V with 2 decimals of accuracy [10:21:11][D][resistance:039]: 'resistance_sensor' - Resistance 7662.0Ω [10:21:11][D][sensor:094]: 'resistance_sensor': Sending state 7661.95508 Ω with 1 decimals of accuracy [10:21:11][D][ntc:026]: 'Temperature' - Temperature: 31.1°C [10:21:11][D][sensor:094]: 'Temperature': Sending state 31.11634 °C with 1 decimals of accuracy [10:21:11][C][nspanel_ha_blueprint:2224]: Wi-Fi: Fair (-60 dBm) [10:21:11][C][nspanel_ha_blueprint:2235]: API: Connected

[10:21:11][C][nspanel_ha_blueprint:2245]: Version: 4.3.12.dev1 [10:21:11][C][nspanel_ha_blueprint:2246]: Init steps: 62 (100.0%)

[10:21:11][C][nspanel_ha_blueprint:2256]: Version: 4.3.12.dev1 [10:21:11][C][nspanel_ha_blueprint:2257]: Compiler: 2024.9.0-dev [10:21:11][C][nspanel_ha_blueprint:2262]: Framework: ESP-IDF [10:21:11][C][nspanel_ha_blueprint:2267]: Free heap: [10:21:11][C][nspanel_ha_blueprint:2271]: Internal: 75216 bytes (26.2%) [10:21:11][C][nspanel_ha_blueprint:2281]: PSRAM: 1981855 bytes (95.1%)

[10:21:11][C][nspanel_ha_blueprint:2289]: Baud rate: 115200 bps [10:21:11][C][nspanel_ha_blueprint:2290]: Queue size: 0

[10:21:14][D][button:010]: 'Update TFT display' Pressed. [10:21:14][D][text_sensor:064]: 'Current Page': Sending state 'home' [10:21:14][D][script.page_changed:2644]: New page: home [10:21:14][D][text_sensor:064]: 'Detailed Entity': Sending state '' [10:21:14][D][nextion_textsensor:014]: Processed text_sensor "current_page" state "home" [10:21:16][D][addon_upload_tft.script.open_upload_dialog:134]: Showing upload dialog page [10:21:16][D][text_sensor:064]: 'Current Page': Sending state 'confirm' [10:21:16][D][script.page_changed:2644]: New page: confirm

[10:21:16][D][nextion_textsensor:014]: Processed text_sensor "current_page" state "confirm" [10:21:16][D][addon_upload_tft.script.report_upload_progress:158]: Set Nextion unavailable for blueprint calls [10:21:16][D][binary_sensor:036]: 'Nextion display': Sending state OFF [10:21:16][D][addon_upload_tft.script.report_upload_progress:158]: Preparing for upload... [10:21:16][D][script.nextion_status:107]: Nextion status: [10:21:16][D][script.nextion_status:108]: Is detected: YES [10:21:16][D][script.nextion_status:109]: Is setup: YES [10:21:16][D][script.nextion_status:110]: Queue size: 13 [10:21:16][D][addon_upload_tft.script.upload_tft:220]: Starting the upload script [10:21:16][D][addon_upload_tft.script.upload_tft:221]: Valid TFT: YES [10:21:16][D][addon_upload_tft.script.upload_tft:222]: Current baud rate: 115200 bps [10:21:16][D][addon_upload_tft.script.upload_tft:223]: Target upload baud rate: 921600 bps [10:21:16][D][addon_upload_tft.script.upload_tft:224]: Upload URL: https://raw.githubusercontent.com/Blackymas/NSPanel_HA_Blueprint/dev/hmi/nspanel_eu.tft [10:21:16][C][esp32_ble_tracker:653]: BLE Tracker: [10:21:16][C][esp32_ble_tracker:654]: Scan Duration: 300 s [10:21:16][C][esp32_ble_tracker:655]: Scan Interval: 320.0 ms [10:21:16][C][esp32_ble_tracker:656]: Scan Window: 30.0 ms [10:21:16][C][esp32_ble_tracker:657]: Scan Type: ACTIVE [10:21:16][C][esp32_ble_tracker:658]: Continuous Scanning: True [10:21:16][D][addon_upload_tft.script.upload_tft:241]: Disable BLE [10:21:16][D][addon_upload_tft.script.upload_tft:245]: Bluetooth proxy: Passive [10:21:16][D][addon_upload_tft.script.upload_tft:253]: Stopping BLE Tracker scan... [10:21:16][D][esp32_ble_tracker:237]: Stopping scan. [10:21:16][D][addon_upload_tft.script.upload_tft:257]: Disabling BLE Tracker scan... [10:21:16][D][addon_upload_tft.script.upload_tft:262]: Disabling BLE... [10:21:17][C][esp32_ble_tracker:653]: BLE Tracker: [10:21:17][C][esp32_ble_tracker:654]: Scan Duration: 300 s [10:21:17][C][esp32_ble_tracker:655]: Scan Interval: 320.0 ms [10:21:17][C][esp32_ble_tracker:656]: Scan Window: 30.0 ms [10:21:17][C][esp32_ble_tracker:657]: Scan Type: PASSIVE [10:21:17][C][esp32_ble_tracker:658]: Continuous Scanning: False [10:21:17][W][component:237]: Component script took a long time for an operation (1332 ms). [10:21:17][W][component:238]: Components should block for at most 30 ms. [10:21:17][D][esp32_ble:269]: Disabling BLE... [10:21:17][D][esp-idf:000][BTU_TASK]: E (415330) BT_BTM: BTM_BleScan scan not active

[10:21:17][D][esp-idf:000][BTU_TASK]: W (415334) BT_APPL: bta_dm_ble_scan stop scan failed, status=0x6

[10:21:17][D][esp-idf:000][BTU_TASK]: W (415340) BT_APPL: bta_dm_disable BTA_DISABLE_DELAY set to 200 ms

[10:21:17][W][component:237]: Component esp32_ble took a long time for an operation (232 ms). [10:21:17][W][component:238]: Components should block for at most 30 ms. [10:21:19][D][addon_upload_tft.script.open_upload_dialog:134]: Showing upload dialog page [10:21:19][D][addon_upload_tft.script.report_upload_progress:158]: Stopping other scripts [10:21:19][D][text_sensor:064]: 'Current Page': Sending state 'confirm' [10:21:19][D][nextion_textsensor:014]: Processed text_sensor "current_page" state "confirm" [10:21:20][D][script.nextion_status:107]: Nextion status: [10:21:20][D][script.nextion_status:108]: Is detected: YES [10:21:20][D][script.nextion_status:109]: Is setup: YES [10:21:20][D][script.nextion_status:110]: Queue size: 0 [10:21:20][D][addon_upload_tft.script.report_upload_progress:158]: Setting baud rate [10:21:20][D][script.set_baud_rate:3022]: Baud rate changing from 115200 to 921600 bps [10:21:20][D][script.set_baud_rate:3023]: Flush UART [10:21:20][D][script.set_baud_rate:3029]: Sending instruction 'baud=921600' to Nextion [10:21:20][D][script.set_baud_rate:3031]: Flush UART [10:21:20][D][script.set_baud_rate:3037]: Set ESPHome new baud rate to 921600 bps [10:21:20][C][uart.idf:153]: UART 0 was reloaded. [10:21:20][C][uart.idf:159]: UART Bus 0: [10:21:20][C][uart.idf:160]: TX Pin: GPIO16 [10:21:20][C][uart.idf:161]: RX Pin: GPIO17 [10:21:20][C][uart.idf:163]: RX Buffer Size: 256 [10:21:20][C][uart.idf:165]: Baud Rate: 921600 baud [10:21:20][C][uart.idf:166]: Data Bits: 8 [10:21:20][C][uart.idf:167]: Parity: NONE [10:21:20][C][uart.idf:168]: Stop bits: 1 [10:21:20][D][script.set_baud_rate:3040]: Current baud rate: 921600 bps [10:21:20][W][nextion:755]: Received unknown event from nextion: 0x80 [10:21:21][D][sensor:094]: 'ntc_source': Sending state 1.34117 V with 2 decimals of accuracy [10:21:21][D][resistance:039]: 'resistance_sensor' - Resistance 7668.4Ω [10:21:21][D][sensor:094]: 'resistance_sensor': Sending state 7668.37354 Ω with 1 decimals of accuracy [10:21:21][D][ntc:026]: 'Temperature' - Temperature: 31.1°C [10:21:21][D][sensor:094]: 'Temperature': Sending state 31.09672 °C with 1 decimals of accuracy [10:21:22][D][main:403]: Attempting to upload TFT [10:21:22][D][addon_upload_tft.script.report_upload_progress:158]: Attempt #1 at 921600 bps [10:21:23][D][addon_upload_tft.script.nextion_upload:118]: Waiting for empty UART and Nextion queues [10:21:28][D][sensor:094]: 'RSSI': Sending state -60.00000 dBm with 0 decimals of accuracy [10:21:31][D][sensor:094]: 'ntc_source': Sending state 1.34200 V with 2 decimals of accuracy [10:21:31][D][resistance:039]: 'resistance_sensor' - Resistance 7676.4Ω [10:21:31][D][sensor:094]: 'resistance_sensor': Sending state 7676.40479 Ω with 1 decimals of accuracy [10:21:31][D][ntc:026]: 'Temperature' - Temperature: 31.1°C [10:21:31][D][sensor:094]: 'Temperature': Sending state 31.07219 °C with 1 decimals of accuracy [10:21:35][D][addon_upload_tft.script.nextion_upload:126]: Starting TFT upload... [10:21:35][D][nextion.upload.idf:157]: Nextion TFT upload requested [10:21:35][D][nextion.upload.idf:158]: Exit reparse: NO [10:21:35][D][nextion.upload.idf:159]: URL: https://raw.githubusercontent.com/Blackymas/NSPanel_HA_Blueprint/dev/hmi/nspanel_eu.tft [10:21:35][D][nextion.upload.idf:188]: Baud rate: 921600 WARNING zolder @ 192.168.2.22: Connection error occurred: [Errno 104] Connection reset by peer INFO Processing unexpected disconnect from ESPHome API for zolder @ 192.168.2.22 WARNING Disconnected from API INFO Successfully connected to zolder @ 192.168.2.22 in 0.013s INFO Successful handshake with zolder @ 192.168.2.22 in 0.076s [10:22:02][W][nextion:081]: Nextion is not connected! [10:22:02][D][sensor:094]: 'ntc_source': Sending state 1.34267 V with 2 decimals of accuracy [10:22:02][D][resistance:039]: 'resistance_sensor' - Resistance 7682.8Ω [10:22:02][D][sensor:094]: 'resistance_sensor': Sending state 7682.83350 Ω with 1 decimals of accuracy [10:22:02][D][ntc:026]: 'Temperature' - Temperature: 31.1°C [10:22:02][D][sensor:094]: 'Temperature': Sending state 31.05257 °C with 1 decimals of accuracy [10:22:02][W][nextion:081]: Nextion is not connected! [10:22:03][W][nextion:081]: Nextion is not connected! [10:22:03][W][nextion:081]: Nextion is not connected! [10:22:04][W][nextion:081]: Nextion is not connected! [10:22:04][W][nextion:081]: Nextion is not connected! [10:22:05][W][nextion:081]: Nextion is not connected! [10:22:05][W][nextion:081]: Nextion is not connected! [10:22:06][W][nextion:081]: Nextion is not connected! [10:22:06][W][nextion:081]: Nextion is not connected! [10:22:07][W][nextion:081]: Nextion is not connected! [10:22:07][W][nextion:081]: Nextion is not connected! [10:22:08][W][nextion:081]: Nextion is not connected! [10:22:08][W][nextion:081]: Nextion is not connected! [10:22:09][W][nextion:081]: Nextion is not connected! [10:22:09][D][api:102]: Accepted 192.168.2.96 [10:22:09][D][api.connection:1398]: Home Assistant 2024.8.3 (192.168.2.96): Connected successfully

[10:22:09][D][time:051]: Synchronized time: 2024-08-29 10:22:09 [10:22:09][D][time.on_time_sync:211]: System clock synchronized [10:22:09][D][time.on_time_sync:212]: Timezone: CET-1CEST,M3.5.0,M10.5.0/3 [10:22:09][D][sensor:094]: 'API uptime': Sending state 1724919680.00000 with 0 decimals of accuracy [10:22:09][D][sensor:094]: 'Device uptime': Sending state 1724919680.00000 with 0 decimals of accuracy [10:22:09][W][nextion:081]: Nextion is not connected! [10:22:10][W][nextion:081]: Nextion is not connected! [10:22:10][W][nextion:081]: Nextion is not connected! [10:22:11][W][nextion:081]: Nextion is not connected! [10:22:11][W][nextion:081]: Nextion is not connected! [10:22:12][W][nextion:081]: Nextion is not connected! [10:22:12][D][script.timer_page:3256]: Fallback to page Home [10:22:12][D][sensor:094]: 'ntc_source': Sending state 1.34175 V with 2 decimals of accuracy [10:22:12][D][resistance:039]: 'resistance_sensor' - Resistance 7674.0Ω [10:22:12][D][sensor:094]: 'resistance_sensor': Sending state 7673.99414 Ω with 1 decimals of accuracy [10:22:12][D][ntc:026]: 'Temperature' - Temperature: 31.1°C [10:22:12][D][sensor:094]: 'Temperature': Sending state 31.07955 °C with 1 decimals of accuracy [10:22:12][W][nextion:081]: Nextion is not connected! [10:22:13][W][nextion:081]: Nextion is not connected! [10:22:13][W][nextion:081]: Nextion is not connected!

Home Assistant Logs

No response

[edwardtfn]

Could you please share a bit more of your log? Ideally from the moment you press "Update TFT" to a few seconds after the panel restarts.

[Mauricewillemstein]

logs_zolder_logs.txt

Here it is.

[Mauricewillemstein]

Also tried it with ble disabeld, clean build files and flashed with serial. But the same result. Also the screen responds to touch, but for example the lights cant be dimmed anymore. HW buttond works fine.

[Mauricewillemstein]

An other update: Flashed the nextion with serial and nextion editor. The tft now is version 4.3.12-dev1. When the panal is starting it says the right version, but in home assistant it says 4.3.11. In the log it says 4.3.12-dev1 Updating from home assistant still fails

[edwardtfn]

This is odd... My panel is reporting correctly on it's device page on Home Assistant:

[edwardtfn]

I see you are compiling with ESPHome v2024.9.0-DEV:

[20:00:20][C][nspanel_ha_blueprint:2257]:   Compiler:    2024.9.0-dev

I will try the same tomorrow. Maybe it is related to something new coming with the next version.

Meanwhile, could you please share updated logs after installing the new TFT?

[Mauricewillemstein]

I have 2 panels. The "zolder" one is on 4.3.12-dev1, copiled with esphome-dev. This one is running fine, exept updating screen wont work. The "scherm" one is on 4.3.11, compiled with the normal esphome 2024.8.1. The tft one this one is 4.3.12-dev1 so i want to flash with 4.3.11 with use of home-assistant. Strangely it makes the same errors as the dev one logs_scherm_logs.txt logs_zolder_logs (2).txt

[Mauricewillemstein]

A little update... Ik i install the tft local (downloaded and in the www forlder) it will upload the display. But even then this is done it wont update from internet. With the display installd i can switch a light on or of, but not the brightness

[vsatmydynipnet]

I run into probably the same. Already enabled changing the baud rate tried different setting. But watching the panel it reboots while setting baud rate is displayed. Home Assistant OS latest version + 4.3.11. Also tried to use dev instead of main. Same result.

[vsatmydynipnet]

Add: Thank you for the hint with local. I put the file into /config/www and then using "update url" it writes the tft out to the panel. Internet is not working even the HA server has access. wget https to /home/hassio , then moving the file to /config/www works.