issues
search
CraneSoftwrights
/
revenge
A peg and card game for the whole family
BSD 3-Clause "New" or "Revised" License
0
stars
0
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Add glue guides to level 3
#37
gkholman
opened
2 days ago
0
Incorporate push checksum in all download file names
#36
gkholman
closed
3 hours ago
0
Increase compartment size by 1/8" all around
#35
gkholman
closed
3 days ago
0
Rotate the shared directory copy of the play surface for use on the landing page
#34
gkholman
closed
3 days ago
0
Review the joker card graphics
#33
gkholman
closed
3 days ago
0
Repair the 7 card graphic faults
#32
gkholman
closed
3 days ago
0
Holes are too large
#31
gkholman
closed
6 days ago
1
Fix 10x10 from larger cut pattern
#30
gkholman
closed
6 days ago
0
Increase peg storage hole size
#29
gkholman
closed
1 week ago
0
Create SBF/SBB with and without holes but with perimeter without alignment holes
#28
gkholman
closed
1 week ago
0
Why is the image shifting down when not using "=!" for the numbered layers?
#27
gkholman
opened
1 week ago
0
Add reference to https://www.makeplayingcards.com/sell/cranesoftwrights
#26
gkholman
opened
2 weeks ago
0
Swap front and back for instruction cards
#25
gkholman
closed
1 week ago
0
Replace edge panel pulls with centred panel pulls
#24
gkholman
closed
2 weeks ago
0
Angle safe area to the start of the target area
#23
gkholman
closed
1 week ago
1
Rule notes
#22
gkholman
opened
2 weeks ago
2
Rename layer "5678" to be just "5" because extra layers may be needed
#21
gkholman
closed
1 week ago
1
Adjust "Revenge" on back cover to make room for rubber foot in top right corner
#20
gkholman
closed
1 week ago
0
Document the peg hole bit size as 1/8"
#19
gkholman
opened
3 weeks ago
0
Fewer checks in checkered flag
#18
gkholman
closed
1 week ago
0
L2 panel outer edges hidden by L1 overhang
#17
gkholman
closed
1 week ago
0
Reorder icons on left L4
#16
gkholman
closed
1 week ago
0
Move pegs farther from source and target in icons
#15
gkholman
closed
1 week ago
0
Change layer 4 thumb holes to single opposite centred semicircle on all four panels
#14
gkholman
closed
2 weeks ago
1
Wider outer oval on target
#13
gkholman
closed
1 week ago
0
Increase peg hole size and add hidable targets for drilling
#12
gkholman
closed
1 week ago
0
Detect non-cut-stroke strokes of less than .002in
#11
gkholman
closed
3 weeks ago
1
Add notches to level three guiding the placement of the doors in level two
#10
gkholman
closed
2 weeks ago
1
Add black raster around door slide areas
#9
gkholman
closed
1 week ago
0
Use narrow font for card indexes
#8
gkholman
closed
1 week ago
0
Clarify in the documentation that copyright is claimed on the appearance and not on the rules
#7
gkholman
opened
3 weeks ago
0
Card making ideas
#6
gkholman
closed
1 week ago
1
Use joker's cap for joker icon in card list
#5
gkholman
closed
3 weeks ago
0
Add weight-loss cut-outs
#4
gkholman
closed
3 weeks ago
0
Consider adding character images in start directions
#3
gkholman
closed
4 weeks ago
0
Add alignment notches to sliding doors for unambiguous placement during build
#2
gkholman
closed
4 weeks ago
0
Add tick marks along pathways, every 4 holes
#1
gkholman
closed
4 weeks ago
1