Hi. Can someone help me please. I flashed bootloader successfully, but now I have this error:
U-Boot 2013.07-gba03eeb (Dec 04 2018 - 21:41:16)
Bootloader-Version: Dafanghacks v2
Board: Dafang 128MB (Ingenic XBurst T20 SoC)
DRAM: 128 MiB
Top of RAM usable for U-Boot at: 84000000
Reserving 419k for U-Boot at: 83f94000
Reserving 32784k for malloc() at: 81f90000
Reserving 32 Bytes for Board Info at: 81f8ffe0
Reserving 124 Bytes for Global Data at: 81f8ff64
Reserving 128k for boot params() at: 81f6ff64
Stack Pointer at: 81f6ff48
Now running in RAM - U-Boot at: 83f94000
MMC: msc: 0
the manufacturer c8
SF: Detected GD25Q128
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Setting yellow_gpio to off:
gpio_request lable = cmd_gpio gpio = 38
gpio: pin 38 (gpio 38) value is 1
Setting blue_gpio to off:
gpio_request lable = cmd_gpio gpio = 39
gpio: pin 39 (gpio 39) value is 1
Setting night_gpios:
gpio_request lable = cmd_gpio gpio = 81
gpio: pin 81 (gpio 81) value is 0
gpio_request lable = cmd_gpio gpio = 49
gpio: pin 49 (gpio 49) value is 0
gpio_request lable = cmd_gpio gpio = 25
gpio: pin 25 (gpio 25) value is 0
Setting USB enable:
gpio_request lable = cmd_gpio gpio = 47
gpio: pin 47 (gpio 47) value is 1
Setting Speaker enable:
gpio_request lable = cmd_gpio gpio = 63
gpio: pin 63 (gpio 63) value is 1
Setting Enable SDCARD:
gpio_request lable = cmd_gpio gpio = 43
gpio: pin 43 (gpio 43) value is 1
gpio_request lable = cmd_gpio gpio = 48
gpio: pin 48 (gpio 48) value is 0
Running SDupdate....
Card did not respond to voltage select!
sdupdate - auto upgrade file from mmc to flash
Usage:
sdupdate LOAD_ID ADDR_START ADDR_END
LOAD_ID: 0-->u-boot
1-->kernel
2-->rootfs
3-->demo.bin
ex:
sdupdate (update all)
or
sdupdate 0 0x0 0x40000
Hit any key to stop autoboot: 0
Card did not respond to voltage select!
MMC not found....
Booting from NAND....
gpio_request lable = cmd_gpio gpio = 38
gpio: pin 38 (gpio 38) value is 0
the manufacturer c8
SF: Detected GD25Q128
--->probe spend 4 ms
SF: 2621440 bytes @ 0x40000 Read: OK
--->read spend 380 ms
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Hi. Can someone help me please. I flashed bootloader successfully, but now I have this error:
U-Boot 2013.07-gba03eeb (Dec 04 2018 - 21:41:16)
Bootloader-Version: Dafanghacks v2 Board: Dafang 128MB (Ingenic XBurst T20 SoC) DRAM: 128 MiB Top of RAM usable for U-Boot at: 84000000 Reserving 419k for U-Boot at: 83f94000 Reserving 32784k for malloc() at: 81f90000 Reserving 32 Bytes for Board Info at: 81f8ffe0 Reserving 124 Bytes for Global Data at: 81f8ff64 Reserving 128k for boot params() at: 81f6ff64 Stack Pointer at: 81f6ff48 Now running in RAM - U-Boot at: 83f94000 MMC: msc: 0 the manufacturer c8 SF: Detected GD25Q128
*** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Setting yellow_gpio to off: gpio_request lable = cmd_gpio gpio = 38 gpio: pin 38 (gpio 38) value is 1 Setting blue_gpio to off: gpio_request lable = cmd_gpio gpio = 39 gpio: pin 39 (gpio 39) value is 1 Setting night_gpios: gpio_request lable = cmd_gpio gpio = 81 gpio: pin 81 (gpio 81) value is 0 gpio_request lable = cmd_gpio gpio = 49 gpio: pin 49 (gpio 49) value is 0 gpio_request lable = cmd_gpio gpio = 25 gpio: pin 25 (gpio 25) value is 0 Setting USB enable: gpio_request lable = cmd_gpio gpio = 47 gpio: pin 47 (gpio 47) value is 1 Setting Speaker enable: gpio_request lable = cmd_gpio gpio = 63 gpio: pin 63 (gpio 63) value is 1 Setting Enable SDCARD: gpio_request lable = cmd_gpio gpio = 43 gpio: pin 43 (gpio 43) value is 1 gpio_request lable = cmd_gpio gpio = 48 gpio: pin 48 (gpio 48) value is 0 Running SDupdate.... Card did not respond to voltage select! sdupdate - auto upgrade file from mmc to flash
Usage: sdupdate LOAD_ID ADDR_START ADDR_END LOAD_ID: 0-->u-boot 1-->kernel 2-->rootfs 3-->demo.bin ex: sdupdate (update all) or sdupdate 0 0x0 0x40000 Hit any key to stop autoboot: 0 Card did not respond to voltage select! MMC not found.... Booting from NAND.... gpio_request lable = cmd_gpio gpio = 38 gpio: pin 38 (gpio 38) value is 0 the manufacturer c8 SF: Detected GD25Q128
--->probe spend 4 ms SF: 2621440 bytes @ 0x40000 Read: OK --->read spend 380 ms Wrong Image Format for bootm command ERROR: can't get kernel image!