Axes lock on start up alarm stet

[Kim9999]

This just started out of the blue. Will not run just locks axes. Removed limit switch hook up still locks...Open software hooks up and locks up.

[Kim9999]

Thank you. I reset the eeprom and reloaded all settings so far it is moving going to test it out today.

On Thu, Apr 12, 2018 at 5:33 AM, ASHIT-AXAR notifications@github.com wrote:

do not touch hardware. it's a safety feature in the software [GRBL] provided to locate precise machine zero. i personally prefer to left it enabled. so during power loss or some kind of failure i can continue the job where i miss.

you can disable that in the Config.h file by commenting out line 88. and upload this new firmware.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-380774025, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3SZm2U1CbBV2rtZSGa8Zaa2fhmQCuks5tnztxgaJpZM4TQazK .

-- Kim Kottas

[Kim9999]

Today I ran a file once no problem now all I get is error 9. I am at a mental block here sorry. I can no longer run any project without error 9. Frustrated! Homes perfect. Limit swithces good, locks up at the first line of code. I jog to position of project 0 out and hit send. It throws an alarm and locks out code. I have read all here and have not found what I am doing wrong. alarm 2 gcode exceeds travel limits,,,but worked fine once then started this alarm on send file.

On Thu, Apr 12, 2018 at 8:15 AM, Kim Kottas klkottas@gmail.com wrote:

Thank you. I reset the eeprom and reloaded all settings so far it is moving going to test it out today.

On Thu, Apr 12, 2018 at 5:33 AM, ASHIT-AXAR notifications@github.com wrote:

do not touch hardware. it's a safety feature in the software [GRBL] provided to locate precise machine zero. i personally prefer to left it enabled. so during power loss or some kind of failure i can continue the job where i miss.

you can disable that in the Config.h file by commenting out line 88. and upload this new firmware.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-380774025, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3SZm2U1CbBV2rtZSGa8Zaa2fhmQCuks5tnztxgaJpZM4TQazK .

-- Kim Kottas

-- Kim Kottas

[Kim9999]

Thank you I found my problem. needed to change $20to 0. Sorry full mental block took some reading.

On Thu, Apr 12, 2018 at 10:34 AM, Kim Kottas klkottas@gmail.com wrote:

Today I ran a file once no problem now all I get is error 9. I am at a mental block here sorry.

On Thu, Apr 12, 2018 at 8:15 AM, Kim Kottas klkottas@gmail.com wrote:

Thank you. I reset the eeprom and reloaded all settings so far it is moving going to test it out today.

On Thu, Apr 12, 2018 at 5:33 AM, ASHIT-AXAR notifications@github.com wrote:

do not touch hardware. it's a safety feature in the software [GRBL] provided to locate precise machine zero. i personally prefer to left it enabled. so during power loss or some kind of failure i can continue the job where i miss.

you can disable that in the Config.h file by commenting out line 88. and upload this new firmware.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-380774025, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3SZm2U1CbBV2rtZSGa8Zaa2fhmQCuks5tnztxgaJpZM4TQazK .

-- Kim Kottas

-- Kim Kottas

-- Kim Kottas

[Kim9999]

Yes I changed these to many settings and all locked it up. I do have limit switches and stop unit. I set the machine to size of bed and just has a fit if I change $20. It did work but now it does not after windows did an update in the middle of a run. I turned off auto windows update! Running air cuts now and all is working. Will throw limit switches and check all of that today. Thank you very much!!! I will send you my set up when I copy the files to this computer.(lap top) HAVE A WONDERFUL DAY!

On Fri, Apr 13, 2018 at 5:46 AM, ASHIT-AXAR notifications@github.com wrote:

soft limits are a good safety feature. i left it enabled too. this assures machine will never damage itself. you need to set correct values for all axes, so machine can work well. related option's are : $130, $131, $132

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-381110774, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3ScJc6BxfGovpNu116SCutVjJa6LNks5toI_5gaJpZM4TQazK .

-- Kim Kottas

[Kim9999]

The lock up happened after a windows update during a run. The only way I found to fix it was to reset the eeprom and reset everything. However I had to turn off soft limits as it would throw an alarm code of 2 and an error code 9. I set the soft limits to several setting with no improvement. I set$20 to 0 now I am up and running. any thoughts on this?

[Kim9999]

Ok here are my settings. I use Vcrave Pro 6.9 I have to reverse X to get text to print correctly and I have to invert x to get the letters A and V to print correctly. Just starting out so may have some settings wrong still. It is working but with the X going reverse of the buttons. Left= right. Thank you for your help and advise.

$$ < $0=10 $1=25 $2=6 $3=6 $4=0 $5=0 $6=0 $10=1 $11=0.010 $12=0.002 $13=1 $20=0 $21=1 $22=1 $23=0 $24=250.000 $25=500.000 $26=250 $27=8.000 $30=500 $31=0 $32=0 $100=800.000 $101=800.000 $102=800.000 $110=500.000 $111=500.000 $112=500.000 $120=2.000 $121=2.000 $122=2.000 $130=600.000 $131=360.000 $132=30.000 ok

$# < [G54:0.0000,0.0000,0.0000] [G55:0.0000,0.0000,0.0000] [G56:0.0000,0.0000,0.0000] [G57:0.0000,0.0000,0.0000] [G58:0.0000,0.0000,0.0000] [G59:0.0000,0.0000,0.0000] [G28:0.0000,0.0000,0.0000] [G30:0.0000,0.0000,0.0000] [G92:0.0000,0.0000,0.0000] [TLO:0.0000] [PRB:0.0000,0.0000,0.0000:0] ok

$G < [GC:G0 G54 G17 G21 G90 G94 M5 M9 T0 F0.0 S200] ok

$I < [VER:1.1f.20170801:] [OPT:V,15,128] ok

$N < $N0= $N1= I over set the 130,31,and 32 settings to get this to work. I have a 300 mm x 180 mm bed or 7 x 12 inches.

Limit switches as shown in gnea/grbl in Wiki using NO switches in parallel with the optiocoupler circuit there. All that is working as it should. With the woodpecker board.

Kim

On Sun, Apr 15, 2018 at 12:55 PM, ASHIT-AXAR notifications@github.com wrote:

first of all, post your grbl settings here. grbl does not alter eeprom settings on its own. you do not need to change grbl source files by default everything you need to config is listed in $$ settings.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-381429323, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3SXEoQ2DDJENBCtbO8_Y1KccUtv1cks5to5ewgaJpZM4TQazK .

-- Kim Kottas

[Kim9999]

V crave Pro 6.0 not 6.9

On Sat, Apr 21, 2018 at 3:53 PM, Kim Kottas klkottas@gmail.com wrote:

Ok here are my settings. I use Vcrave Pro 6.9 I have to reverse X to get text to print correctly and I have to invert x to get the letters A and V to print correctly. Just starting out so may have some settings wrong still. It is working but with the X going reverse of the buttons. Left= right. Thank you for your help and advise.

$$ < $0=10 $1=25 $2=6 $3=6 $4=0 $5=0 $6=0 $10=1 $11=0.010 $12=0.002 $13=1 $20=0 $21=1 $22=1 $23=0 $24=250.000 $25=500.000 $26=250 $27=8.000 $30=500 $31=0 $32=0 $100=800.000 $101=800.000 $102=800.000 $110=500.000 $111=500.000 $112=500.000 $120=2.000 $121=2.000 $122=2.000 $130=600.000 $131=360.000 $132=30.000 ok

$# < [G54:0.0000,0.0000,0.0000] [G55:0.0000,0.0000,0.0000] [G56:0.0000,0.0000,0.0000] [G57:0.0000,0.0000,0.0000] [G58:0.0000,0.0000,0.0000] [G59:0.0000,0.0000,0.0000] [G28:0.0000,0.0000,0.0000] [G30:0.0000,0.0000,0.0000] [G92:0.0000,0.0000,0.0000] [TLO:0.0000] [PRB:0.0000,0.0000,0.0000:0] ok

$G < [GC:G0 G54 G17 G21 G90 G94 M5 M9 T0 F0.0 S200] ok

$I < [VER:1.1f.20170801:] [OPT:V,15,128] ok

$N < $N0= $N1= I over set the 130,31,and 32 settings to get this to work. I have a 300 mm x 180 mm bed or 7 x 12 inches.

Limit switches as shown in gnea/grbl in Wiki using NO switches in parallel with the optiocoupler circuit there. All that is working as it should. With the woodpecker board.

Kim

On Sun, Apr 15, 2018 at 12:55 PM, ASHIT-AXAR notifications@github.com wrote:

first of all, post your grbl settings here. grbl does not alter eeprom settings on its own. you do not need to change grbl source files by default everything you need to config is listed in $$ settings.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-381429323, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3SXEoQ2DDJENBCtbO8_Y1KccUtv1cks5to5ewgaJpZM4TQazK .

-- Kim Kottas

-- Kim Kottas

[Kim9999]

Yes I have to invert X for text print correctly but I have to mirror the text too. BUT it is not correct it is a work around. Reading about Machine positions and work piece position it has to be something I do not have correct yet

Thank you Kim Kottas

On Sun, Apr 22, 2018 at 10:02 AM, ASHIT-AXAR notifications@github.com wrote:

ok, step by step to solve the problem. here you inverted Y and Z. let's verify axes movements. on the panel: for X: pressing button right should move to the right "+X" "from negative to zero" or "from zero to positive", button left for opposite. for Y: pressing button up should move the machine head away from you "+Y" (to zero or positive). button down for opposite. for Z: pressing button up should move up "+Z" (to zero or positive). button down for opposite.

anything else is incorrect and you should invert direction mask ($3)

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-383391963, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3SUtRYyMd5e8oY7vqwqJRFXlGPjQiks5trKl_gaJpZM4TQazK .

-- Kim Kottas

[Kim9999]

I have tried several combinations to see what it would do and none work unless I mirror my project and do work around on X.

On Sun, Apr 22, 2018 at 8:11 PM, Kim Kottas klkottas@gmail.com wrote:

Yes I have to invert X for text print correctly but I have to mirror the text too. BUT it is not correct it is a work around. Reading about Machine positions and work piece position it has to be something I do not have correct yet

Thank you Kim Kottas

On Sun, Apr 22, 2018 at 10:02 AM, ASHIT-AXAR notifications@github.com wrote:

ok, step by step to solve the problem. here you inverted Y and Z. let's verify axes movements. on the panel: for X: pressing button right should move to the right "+X" "from negative to zero" or "from zero to positive", button left for opposite. for Y: pressing button up should move the machine head away from you "+Y" (to zero or positive). button down for opposite. for Z: pressing button up should move up "+Z" (to zero or positive). button down for opposite.

anything else is incorrect and you should invert direction mask ($3)

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/Denvi/Candle/issues/227#issuecomment-383391963, or mute the thread https://github.com/notifications/unsubscribe-auth/AiA3SUtRYyMd5e8oY7vqwqJRFXlGPjQiks5trKl_gaJpZM4TQazK .

-- Kim Kottas

-- Kim Kottas