search

Denvi / Candle

GRBL controller application with G-Code visualizer written in Qt.
GNU General Public License v3.0
1.35k stars 548 forks source link

Candle just stop send G code lines #566

Open vilian12306 opened 2 years ago

vilian12306 commented 2 years ago

Versions

PC info

Describe the bug When in Run state,I open a CNC G code file and touch Send command.Candle just send a few lines then stop. Attainments are G code file,Bus Hund traced files and Candle UI picture. So I want to know in what condition does Candle stop sending?

To Reproduce Steps to reproduce the behavior: Candle Test.zip

  1. Go to '...'
  2. Click on '....'
  3. Scroll down to '....'
  4. See error

Expected behavior A clear and concise description of what you expected to happen.

Screenshots If applicable, add screenshots to help explain your problem.

Example files Add G-code files that cause problems.

Additional context Add any other context about the problem here.

mar0x commented 2 years ago

Hello. Please enable program gcode output to console, reproduce the issue and share console output and your GRBL settings (response for '$$' command). The screenshot of the full Candle window after stop would be helpful too.

It is possible your machine reach the limit (hard or soft).

Playerarrs70 commented 1 year ago

same with me here. the program stops working and the servo spins insane. Tried to reset it and start over again but ended in exact line gcode and exact problem.

mar0x commented 1 year ago

@Playerarrs70, same for you up there.

Playerarrs70 commented 1 year ago

Here some screenshots. Screenshot 2022-10-29 165455

As you can see the program stop when I send input to draw the horizontal line. It doesn't happen in vertical line, at least yet. And last week (when my first comment) it's worse.

Screenshot 2022-10-29 165751

As you can see in the screenshot it stop on the red circle on T letter. I thought it was calibration error so I shrink the $100,101,102 value and it works. But it's happen again with longer line

And here's my settings Grbl 1.1h ['$' for help] $$ < $0=10 $1-25 $2=0 $3=0 $4-0 $5-0 $6=0 $10=1 $11-0.010 $12=0.002 $13-0 $20=0 $21-0 $22-0 $23-0 $24-25.000 $25=500.000 $26=250 $27=1.000 $30-1000 $31-0 $32=0 $100-781.250 $101-781.250 $102-78.000 $110-5000.000 $111-5000.000 $112-5000.000 $120-200.000 $121=10.000 $122-10.000 $130-200.000 $131-200.000 $132-200.000

mar0x commented 1 year ago

According to console output on the first screenshot, CNC report "error:22" which is caused by invalid feed rate (F0.0). Please fix your gcode program.

mar0x commented 1 year ago

Consider use "Check mode" (see the check box at the left bottom) before actual run. What software you are using to generate the gcode? Perhaps it requires configuration to generate proper gcode.

Playerarrs70 commented 1 year ago

Thanks for the reply and advice. I use this app called StickFont here's some screenshots of the app. This app can convert text to gcode instantly. I have seen some tutorial from the internet to convert text to gcode and I found this app. Any advice for app to convert text to gcode ?

IMG-20221030-WA0000

Lastly may i ask for proper nc file for just test ? I haven't make my machine running smoothly without error.

mar0x commented 1 year ago

It seems you need to adjust "Plunge feedrate" and "Feedrate" values. It's a spindle move speed in "mm/minute". Start from "50" and increase if you think your machine may mill faster.

I usually use Inkscape with Gcodetools. The user interface is not user-friendly and it requires some experience. It's a good idea to review (and fix) produced gcode files in text editor. See attached system_text.zip with .svg and produced .ngc files.