OTAA activation not working on TTN

[mo-norant]

Hi,

when i am activating over OTAA the Activation frame gets recognized, but the payload frames are not transmitted because it's not connected on the TTN network. APB activation does work without any problems.

Theory, does the low RSSI of -119 mean something?

Here you can find my code.

`

include

include <TinyGPS++.h>

include

include <hal/hal.h>

include

include "WiFi.h"

include

define BUILTIN_LED 25

char s[32]; // used to sprintf for Serial output

TinyGPSPlus gps; static u1_t DEVEUI[8] = {0xF3, 0x4B, 0x37, 0x43, 0x98, 0x3B, 0xAC, 0x00}; static u1_t APPEUI[8] = {0x9C, 0x03, 0x03, 0xD0, 0x7E, 0xD5, 0xB3, 0x70}; static u1_t APPKEY[16] = {0x71, 0x3B, 0x80, 0x81, 0xB0, 0xA1, 0x7A, 0xEA, 0x5D, 0xD8, 0xBA, 0xCC, 0xCF, 0x13, 0xE6, 0x10};

RTC_NOINIT_ATTR int RTCseqnoUp, RTCseqnoDn; RTC_NOINIT_ATTR u4_t otaaDevAddr; RTC_NOINIT_ATTR u1_t otaaNetwKey[16]; RTC_NOINIT_ATTR u1_t otaaApRtKey[16];

void os_getDevEui(u1_t buf) { memcpy_P(buf, DEVEUI, 8); } void os_getArtEui(u1_t buf) { memcpy_P(buf, APPEUI, 8); } void os_getDevKey(u1_t *buf) { memcpy_P(buf, APPKEY, 16); }

static osjob_t sendjob; const unsigned TX_INTERVAL = 30;

const lmic_pinmap lmic_pins = { .nss = 18, .rxtx = LMIC_UNUSED_PIN, .rst = 14, .dio = {26, 33, 32}, };

unsigned long last_update = 0; String toLog; uint8_t txBuffer[] = "Hey mo alles goed.";

void storeFrameCounters() { RTCseqnoUp = LMIC.seqnoUp; RTCseqnoDn = LMIC.seqnoDn; sprintf(s, "Counters stored as %d/%d", LMIC.seqnoUp, LMIC.seqnoDn); Serial.println(s); }

void restoreFrameCounters() { LMIC.seqnoUp = RTCseqnoUp; LMIC.seqnoDn = RTCseqnoDn; sprintf(s, "Restored counters as %d/%d", LMIC.seqnoUp, LMIC.seqnoDn); Serial.println(s); }

void setOrRestorePersistentCounters() { esp_reset_reason_t reason = esp_reset_reason(); if ((reason != ESP_RST_DEEPSLEEP) && (reason != ESP_RST_SW)) { Serial.println(F("Counters both set to 0")); LMIC.seqnoUp = 0; LMIC.seqnoDn = 0; } else { restoreFrameCounters(); } } void do_send(osjob_t *j) { // Check if there is not a current TX/RX job running if (LMIC.opmode & OP_TXRXPEND) { Serial.println(F("OP_TXRXPEND, not sending")); } else {

    CayenneLPP lpp(160);

    lpp.reset();
    lpp.addDigitalInput(1, random(2));
    lpp.addDigitalOutput(2, 1);
    lpp.addAnalogInput(3, 1.23f);
    lpp.addAnalogOutput(4, 3.45f);
    lpp.addLuminosity(5, 20304);

    LMIC_setTxData2(1, txBuffer, sizeof(txBuffer), 1);
    // LMIC_setTxData2(1, lpp.getBuffer(), lpp.getSize(), 0);
    Serial.println(F("Packet queued"));
    digitalWrite(BUILTIN_LED, HIGH);
}
// Next TX is scheduled after TX_COMPLETE event.

}

void onEvent(ev_t ev) { switch (ev) { case EV_SCAN_TIMEOUT: Serial.println(F("EV_SCAN_TIMEOUT")); break; case EV_BEACON_FOUND: Serial.println(F("EV_BEACON_FOUND")); break; case EV_BEACON_MISSED: Serial.println(F("EV_BEACON_MISSED")); break; case EV_BEACON_TRACKED: Serial.println(F("EV_BEACON_TRACKED")); break; case EV_JOINING: Serial.println(F("EV_JOINING")); break; case EV_JOINED: Serial.println(F("EV_JOINED")); // Disable link check validation (automatically enabled // during join, but not supported by TTN at this time). LMIC_setLinkCheckMode(0); break; case EV_RFU1: Serial.println(F("EV_RFU1")); break; case EV_JOIN_FAILED: Serial.println(F("EV_JOIN_FAILED")); break; case EV_REJOIN_FAILED: Serial.println(F("EV_REJOIN_FAILED")); //break; break; case EV_TXCOMPLETE: Serial.println(F("EV_TXCOMPLETE (includes waiting for RX windows)")); digitalWrite(BUILTIN_LED, LOW); if (LMIC.txrxFlags & TXRX_ACK) { Serial.println(F("Received ack")); } if (LMIC.dataLen) { Serial.println(F("Received ")); Serial.println(LMIC.dataLen); Serial.println(F(" bytes of payload")); } storeFrameCounters();

    // Schedule next transmission
    os_setTimedCallback(&sendjob, os_getTime() + sec2osticks(TX_INTERVAL), do_send);
    break;
case EV_LOST_TSYNC:
    Serial.println(F("EV_LOST_TSYNC"));
    break;
case EV_RESET:
    Serial.println(F("EV_RESET"));
    break;
case EV_RXCOMPLETE:
    // data received in ping slot
    Serial.println(F("EV_RXCOMPLETE"));
    break;
case EV_LINK_DEAD:
    Serial.println(F("EV_LINK_DEAD"));
    break;
case EV_LINK_ALIVE:
    Serial.println(F("EV_LINK_ALIVE"));
    break;
default:
    Serial.println(F("Unknown event"));
    break;
}

}

void setup() { Serial.begin(115200); //Turn off WiFi and Bluetooth WiFi.mode(WIFI_OFF); btStop();

SPI.begin(5, 19, 27);
// LMIC init
os_init();
// Reset the MAC state. Session and pending data transfers will be discarded.
LMIC_reset();

esp_reset_reason_t reason = esp_reset_reason();
if ((reason == ESP_RST_DEEPSLEEP) || (reason == ESP_RST_SW))
{
    LMIC_setSession(0x1, otaaDevAddr, otaaNetwKey, otaaApRtKey);
}

LMIC_setupChannel(0, 868100000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI);  // g-band
LMIC_setupChannel(1, 868300000, DR_RANGE_MAP(DR_SF12, DR_SF7B), BAND_CENTI); // g-band
LMIC_setupChannel(2, 868500000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI);  // g-band
LMIC_setupChannel(3, 867100000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI);  // g-band
LMIC_setupChannel(4, 867300000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI);  // g-band
LMIC_setupChannel(5, 867500000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI);  // g-band
LMIC_setupChannel(6, 867700000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI);  // g-band
LMIC_setupChannel(7, 867900000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI);  // g-band
LMIC_setupChannel(8, 868800000, DR_RANGE_MAP(DR_FSK, DR_FSK), BAND_MILLI);   // g2-band

// TTN uses SF9 for its RX2 window.
LMIC.dn2Dr = DR_SF9;
LMIC_setClockError(MAX_CLOCK_ERROR * 1 / 100);

// Disable link check validation
LMIC_setLinkCheckMode(0);

// Set data rate and transmit power for uplink (note: txpow seems to be ignored by the library)
LMIC_setDrTxpow(DR_SF7, 14);
setOrRestorePersistentCounters();

// Start job
do_send(&sendjob);
pinMode(BUILTIN_LED, OUTPUT);
digitalWrite(BUILTIN_LED, LOW);

}

void loop() { os_runloop_once(); }`

[vincegre]

OTAA is confirmed not working: https://github.com/DeuxVis/Lora-TTNMapper-T-Beam/issues/21#issuecomment-670556202 only ABP !

[mo-norant]

Yeah indeed, does somebody has an answer to the code?

[vincegre]

Yeah indeed, does somebody has an answer to the code?

Hum not sure to understand what is your problem as you stated it works fine in ABP mode no ? Which version of board do you have ? mine is 1.1 and not working with that code (no TTN connection and OLED display doesn't work too :(

[DeuxVis]

OTAA was working with the supported versions of the boards (up to V0.7) last time I checked.

Let's concentrate on the support of the newer (V1.0 / V1.1) board versions before talking about OTAA, see #21 #19