Closed StephaneG38 closed 2 years ago
ca revient
Faut voir avec un autre module d1 mini, ou vérifier que son alim est correcte aussi
Je vais être obligé de te laisser merci pour ton aide A demain si tu es dispo Bonne soirée Stéphane
Je vais essayer
idem
Je te laisse Bonne soirée !
Hello, Le montage que j'utilise fonctionne bien avec mes 3 autres compteurs sagem.
Quel en est le schéma?
C'est un wifinfo réalisé par rolrider
Ci-dessous le schémas
Coté schéma, tout à l'air bon. Je viens de contacter Enedis, et en 2 minutes, ils ont passé mon compteur en mode Standard.
De mon coté, tout fonctionne bien :
Pas de lettre q (j'ai bien un 1 dans mon ADSC). l'url getAllLabel fonctionne aussi correctement :
Réactif Enedis !! De mon coté j'ai rebranché mon RPI avec Jeedom et téléinfo avec un modem USB carte electronique et tout fonctionne bien.
un défaut d'affichage ? :
Je comprends pas !
Par contre les valeurs des phases ne sont pas bonnes :
UMOY1 et URMS3 sont 2 étiquettes différentes. et une puissance de 40000W sur la phase3 parait délirant oui
Je vais refaire une config propre jeedom juste avec le teleinfo
Sinon en mode historique cela fonctionne ? Je peux voir avec enedis pour rebasculer. J'étais passé en standard pour avoir la production mais apparemment il faut faire encore une demande pour passer en producteur. Hors je suis en autoconso donc pas producteur et ils ne veulent pas faire la modif chez enedis. Donc EAIT est toujours à 0 en téléinfo alors que sur le compteur il indique 146 kwh
Oui, En Historique, ça fonctionne aussi.
Du coup je ne sais plus quoi faire !
avec le RPi et Jeedom, en recréant l'équipement, y a-t-il toujours des étiquettes incorrectes?
J'ai ca !
Pour l'intensité instantanée je pense qu'il faut prendre :
Ce qui me semble correspondre au compteur
J'utilise le dernier doc d'Enedis : Enedis-NOI-CPT_54E.pdf As-tu un besoin particulier d'avoir l'intensité?
En passant le plugin en débug, ca sort du log interessant je pense
tout à l'air OK Attention, il te faut supprimer ce log car il contient des infos sensibles!
Je te conseille de faire un test avec tasmota : https://tasmota.github.io/docs/Teleinfo/
Je vais tester avec Tasmota dans l'après midi
Hello, Test avec Tasmota
Aprés j'ai fait dans les commandes : EnergyConfig standard
00:00:00.001 HDW: ESP8266EX 00:00:00.050 CFG: Loaded from flash at F5, Count 31 00:00:00.055 QPC: Count 1 00:00:00.064 Project tasmota - Tasmota Version 2022.01.3(teleinfo)-2_7_4_9(2022-02-01T14:35:17) 00:00:00.064 TIC: RX on GPIO13, baudrate 9600 00:00:00.106 SNS: Hardware Serial 00:00:00.106 TIC: using hardware serial 00:00:00.521 WIF: Connecting to AP1 SG Channel 6 BSSId 60:35:C0:C4:2A:96 in mode 11n as tasmota-9F52DB-4827... 00:00:03.501 WIF: Connected 00:00:03.752 HTP: Web server active on tasmota-9F52DB-4827 with IP address 192.168.1.16 16:40:19.298 MQT: Attempting connection... 16:40:19.317 MQT: Connected 16:40:19.319 MQT: tele/tasmota_9F52DB/LWT = Online (retained) 16:40:19.321 MQT: cmnd/tasmota_9F52DB/POWER = 16:40:19.331 MQT: tele/tasmota_9F52DB/INFO1 = {"Info1":{"Module":"Generic","Version":"2022.01.3(teleinfo)","FallbackTopic":"cmnd/DVES_9F52DB_fb/","GroupTopic":"cmnd/tasmotas/"}} 16:40:19.335 MQT: tele/tasmota_9F52DB/INFO2 = {"Info2":{"WebServerMode":"Admin","Hostname":"tasmota-9F52DB-4827","IPAddress":"192.168.1.16"}} 16:40:19.338 MQT: tele/tasmota_9F52DB/INFO3 = {"Info3":{"RestartReason":"Software/System restart"}} 16:40:21.455 QPC: Reset 16:40:24.417 MQT: tele/tasmota_9F52DB/STATE = {"Time":"2022-02-01T16:40:24","Uptime":"0T00:00:11","UptimeSec":11,"Vcc":2.832,"Heap":26,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"Wifi":{"AP":1,"SSId":"SG","BSSId":"60:35:C0:C4:2A:96","Channel":6,"Mode":"11n","RSSI":100,"Signal":-27,"LinkCount":1,"Downtime":"0T00:00:05"}} 16:40:24.427 MQT: tele/tasmota_9F52DB/SENSOR = {"Time":"2022-02-01T16:40:24","ENERGY":{"TotalStartTime":"2022-02-01T16:07:50","Total":0.000,"Yesterday":0.000,"Today":0.000,"Period": 0,"Power": 0,"Current":0.000},"TIC":{}} 16:41:48.269 CMD: EnergyConfig 16:41:48.273 TIC: Settings Mode:standard, RX:GPIO13, EN:None, Raw:noraw, Skip:0, Limit:0 16:41:48.277 MQT: stat/tasmota_9F52DB/RESULT = {"EnergyConfig":"Done"}
Mais toujours rien !!
Dans MQTT
Je viens de tester avec le firmware de Teleinfo 9.1.1 by Nicolas Bernaerts https://github.com/NicolasBernaerts/tasmota/tree/master/teleinfo
J'ai 230 v !! Super !!
Et des messages de partout dans MQTT
Je dois vraiment être nul !!!!
EUREKA !!!! J'ai fait un proto suivant le schéma V2.2 et utilisé la dernière release WirelessTeleInfo.v1.4.1-3.4.1 et tout semble fonctionner !!
GRAND MERCI pour ta patience et ton aide. Stéphane
cool!!!! ça, c'est la persévérence. :-D
Effectivement j'ai pas lâché sur ce coup la mais beaucoup de temps passé ! Encore merci pour ton aide et bravo pour le travail que tu as fait sur ce projet. A bientôt Stéphane
Bonjour, Bravo pour ce projet qui m'intéresse fortement car j'ai 3 compteurs à monitorer. Pouvez vous m'indiquer ou trouver le PCB pour ce projet ? Merci par avance Stéphane