search

EVA-3D / eva-main

Main repository of the EVA project
https://main.eva-3d.page/
Other
274 stars 50 forks source link

[EP] EVA 3 E3D Revo Six and E3D V6 Support #87

Open githubcura35 opened 2 years ago

githubcura35 commented 2 years ago

EVA 3 now supports the E3D Revo Voron. Are there any plans to support the E3D Revo Six? (https://e3d-online.com/products/revo-six) Any plans to support V6 based hotends at all?

pkucmus commented 2 years ago

This would also mean support for V6, right? Not sure about the timing but something I'd like to address

huzargarden commented 2 years ago

Definitely, something that I'll be looking for. I like the EVA design and I'm very happy with my V6 Hot End.

a937983423 commented 2 years ago

I would like to ask why the most popular E3D_ V6 does not support

pkucmus commented 2 years ago

I would like to ask why the most popular E3D_ V6 does not support

According to the EVA survey taken more than a year ago, V6 had 11.5% of the usage I can only imagine that number being lower now. It's an old and relatively underperforming hotend, it's popularity overall means nothing in terms of popularity in the scope of EVA users. Also you asked the question in the ticket that is here to add support for that hotend so in case you just wanted to see an answer it's as above, otherwise, it's just patience.

fj-guy commented 2 years ago

The old e3d v6 served me well for quite awhile. Since the Revo 6 was a direct drop-in replacement I switched to that. And I would imaginge a lot of V6 users did the same. Not all of us care to print at 300mm/s with crazy accel values. I recently upgraded to the V-CORE-3.1 but had retained the older 2.4 carriage because I didn't want to upgrade to a HF hotend just yet. Luckily someone did a V6 mount for EVA 3. Do your survey on REVO 6 users instead of V6 users.

MechanizedMedic commented 2 years ago

I just got done drawing up a to-spec remix that is compatible with Volcano/V6 (if push fitting is removed). It should allow the Volcano and v6 to use the same hotend block with the standard cooling duct.

I also made a cable mount for the BMG extruder but it is only compatible with the single 50mm blower for now.

Feedback and collaboration are welcome! :)

githubcura35 commented 2 years ago

@MechanizedMedic Thanks a lot. I am unable to export to STL. Can you grand permissions in Onshape?

MechanizedMedic commented 2 years ago

@githubcura35, yep sorry about that. Should be good now.

githubcura35 commented 2 years ago

@MechanizedMedic Thanks a lot. I will check it out but feedback will take some time.

githubcura35 commented 2 years ago

@MechanizedMedic The V6 fits perfectly but I am having some trouble with the cooling. The duct from the default bottom reaches furhter down than the tip of the nozzle eva3-v6

MechanizedMedic commented 2 years ago

@githubcura35 It should line up if you move the "hotend_volcano" block down one slot in the "universal_front" reciever. I tried to size it so the Volcano or V6 would fit by moving this mounting location

Like this.

githubcura35 commented 2 years ago

@MechanizedMedic There is no way to move "hotend_volcano" further down as the zip tie holder collides with the "universal_front". colision

To make that work the zip tie holder needs to be moved further up in the "hotend_volcano" or we need a new "v6_front". As a workaround I could grind of a little bit from the "universal_front".

MechanizedMedic commented 2 years ago

Okay, thanks for testing. I'll fix it up later this evening and repost.

olivbd commented 2 years ago

Why not use this Printables model? https://www.printables.com/model/201093-eva-30-e3dv6-revo-revo-micro-hotends-mount

I printed and used it for several months without any problem...

MechanizedMedic commented 2 years ago

@githubcura35, I updated the design this morning to move the hotend down 7.5mm. This should put the v6 in the correct spot for the standard duct. The Volcano hotend will now need the Volcano duct.

githubcura35 commented 2 years ago

@MechanizedMedic Thanks a lot for your effort. The "hotend_volcano" now perfectly fits the "universal_front". I have not done any actual printing as my custom printer is currently not ready for printing. This will take some time but from what I can tell this looks very promissing.

TekuSP commented 1 year ago

Why not use this Printables model? https://www.printables.com/model/201093-eva-30-e3dv6-revo-revo-micro-hotends-mount

I printed and used it for several months without any problem...

That is REVO V6 and not V6 standard

olivbd commented 1 year ago

Why not use this Printables model? https://www.printables.com/model/201093-eva-30-e3dv6-revo-revo-micro-hotends-mount I printed and used it for several months without any problem...

That is REVO V6 and not V6 standard

No, there are two versions: Revo V6 and V6 standard.