Problem starting

[trombose009]

Hello,

I have a new problem during boot process.

D: SD Card Mount Failed! D: Create list with acceptable WiFi networks D: Added fritzboxdampf to list of networks D: Added dampfmaschine2 to list of networks D: End adding networks

Brownout detector was triggered

ets Jun 8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:1216 ho 0 tail 12 room 4 load:0x40078000,len:10864 load:0x40080400,len:6432 entry 0x400806b8

D: Starting ESP32-radio running on CPU 1 at 240 MHz. Version Tue, 14 Jul 2020 09:40:00 GMT. Free memory 247920 D: Display type is BLUETFT D: Partition nvs found, 20480 bytes D: Read 43 keys from NVS D: pin_ir set to 35 D: pin_enc_clk set to 25 D: pin_enc_dt set to 26 D: pin_enc_sw set to 27 D: pin_tft_cs set to 15 D: pin_tft_dc set to 2 D: pin_tft_scl set to -1 D: pin_tft_sda set to -1 D: pin_tft_bl set to -1 D: pin_tft_blx set to -1 D: pin_sd_cs set to 21 D: pin_ch376_cs set to -1 D: pin_ch376_int set to -1 D: pin_vs_cs set to 5 D: pin_vs_dcs set to 16 D: pin_vs_dreq set to 4 D: pin_shutdown set to -1 D: pin_shutdownx set to -1 D: pin_spi_sck set to 18 D: pin_spi_miso set to 19 D: pin_spi_mosi set to 23 D: GPIO0 is HIGH D: GPIO2 is LOW, probably no PULL-UP D: GPIO4 is HIGH D: GPIO5 is HIGH D: GPIO12 is HIGH D: GPIO13 is HIGH D: GPIO14 is HIGH D: GPIO15 is HIGH D: GPIO16 is HIGH D: GPIO17 is HIGH D: GPIO18 is LOW, probably no PULL-UP D: GPIO19 is HIGH D: GPIO21 is HIGH D: GPIO22 is HIGH D: GPIO23 is HIGH D: GPIO25 is HIGH D: GPIO26 is HIGH D: GPIO27 is HIGH D: GPIO32 is HIGH D: GPIO33 is HIGH D: GPIO34 is LOW, probably no PULL-UP D: GPIO35 is LOW, probably no PULL-UP D: GPIO39 is LOW, probably no PULL-UP D: gpio_00 will execute uppreset = 1 D: gpio_12 will execute upvolume = 2 D: gpio_13 will execute downvolume = 2 D: Enable pin 35 for IR D: Start display D: SD Card Mount Failed! D: Create list with acceptable WiFi networks D: Added fritzboxdampf to list of networks D: Added dampfmaschine2 to list of networks D: End adding networks

Brownout detector was triggered

ets Jun 8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:1216 ho 0 tail 12 room 4 load:0x40078000,len:10864 load:0x40080400,len:6432 entry 0x400806b8

D: Starting ESP32-radio running on CPU 1 at 240 MHz. Version Tue, 14 Jul 2020 09:40:00 GMT. Free memory 247920 D: Display type is BLUETFT .......

During the last days, I tried to connect the radio to my wifi. I added 2 wifi credentials to the ESP32_radio_init.ino, uploaded it and the upload the esp32_radio.ino. After that, in the log, the two SSIDs shwon up but it just did not connect to wifi. Today, I wanted to give it another try but now I have some error during boot process (boot loop). Does anyone has an idea what'S the problem?

greetings

[Edzelf]

"brownout" means that the voltage of the power source is lower than a certain limit. In other words: the power source is too weak.

[trombose009]

ok. that was easy :-P

but now, the first problem. It does not connect to the wifi:

D: SD Card Mount Failed! D: Create list with acceptable WiFi networks D: Added fritzboxdampf to list of networks D: Added dampfmaschine2 to list of networks D: End adding networks D: Scan Networks D: Scan completed D: Number of available networks: 2 D: 1 - dampfmaschine2 Signal: -77 dBm, Encryption WPA2_PSK, Acceptable D: 2 - fritzboxdampf Signal: -84 dBm, Encryption WPA_WPA2_PSK, Acceptable D: End of list D: Command: clk_dst with parameter 1 D: Command: clk_offset with parameter 1 D: Command: clk_server with parameter pool.ntp.org D: Command: gpio_00 with parameter uppreset = 1 D: Command: gpio_12 with parameter upvolume = 2 D: Command: gpio_13 with parameter downvolume = 2 D: Command: ir_40bf with parameter upvolume = 2 D: Command: ir_c03f with parameter downvolume = 2 D: Command: mqttbroker with parameter none D: Command: mqttpasswd with parameter *** D: Command: mqttport with parameter 1883 D: Command: mqttprefix with parameter none D: Command: mqttuser with parameter none D: Command: pin_enc_clk with parameter 25 D: Command: pin_enc_dt with parameter 26 D: Command: pin_enc_sw with parameter 27 D: Command: pin_ir with parameter 35 D: Command: pin_sd_cs with parameter 21 D: Command: pin_tft_cs with parameter 15 D: Command: pin_tft_dc with parameter 2 D: Command: pin_vs_cs with parameter 5 D: Command: pin_vs_dcs with parameter 16 D: Command: pin_vs_dreq with parameter 4 D: Command: preset with parameter 6 D: Command: preset_00 with parameter 109.206.96.34:8100 D: Command: preset_01 with parameter airspectrum.cdnstream1.com:8114/1648_128 D: Command: preset_02 with parameter us2.internet-radio.com:8050 D: Command: preset_03 with parameter airspectrum.cdnstream1.com:8000/1261_192 D: Command: preset_04 with parameter airspectrum.cdnstream1.com:8008/1604_128 D: Command: preset_05 with parameter us1.internet-radio.com:8105 D: Command: preset_06 with parameter icecast.omroep.nl:80/radio1-bb-mp3 D: Command: preset_07 with parameter 205.164.62.15:10032 D: Command: preset_08 with parameter skonto.ls.lv:8002/mp3 D: Command: preset_09 with parameter 94.23.66.155:8106 D: Command: preset_10 with parameter ihr/IHR_IEDM D: Command: preset_11 with parameter ihr/IHR_TRAN D: Command: toneha with parameter 0 D: Command: tonehf with parameter 0 D: Command: tonela with parameter 0 D: Command: tonelf with parameter 0 D: Command: volume with parameter 72 D: Slow SPI, Testing VS1053 read/write registers... D: Fast SPI, Testing VS1053 read/write registers again... D: endFillByte is 0 D: Start CH376

here it stops.

[Edzelf]

Remove the definition of CH376 and SDCARD if you don't have it. Around line 168.

[trombose009]

Thank you so much. It's great to get answers also to such easy questions.

Now I run into a wifi problem:

D: Slow SPI, Testing VS1053 read/write registers... D: Fast SPI, Testing VS1053 read/write registers again... D: endFillByte is 0 D: Connect to WiFi E (5722) wifi: esp_wifi_scan_start 1245 wifi not start E (5722) wifi: esp_wifi_disconnect 1153 wifi not start E (5722) wifi: esp_wifi_scan_start 1245 wifi not start D: WiFi Failed! Trying to setup AP with name ESP32Radio and password ESP32Radio. D: IP = 192.168.4.1 D: Start server for commands D: Rotary encoder is enabled D: STOP requested D: Song stopped correctly after 0 msec

I just did some reacherches in the internet and figured out, that it might be a bug in the wifi library. But maybe someone does know the issue and can help.

[trombose009]

Edzelf solved my starting problems. So I do another case for the wifi thing