First of all, thank you very much for your time and support and congratulations for your magnificent software. Now that I'm done with the box, I'm having issues with the system. It's the first time I have to reinstall it because at some time it restarts and keeps rebooting or hangs forever. I suspect a hardware issue, but I would like to give it another try before tossing the esp32 into the bin.
This time, while I was listening to some music, it restarted without being able to start again. This is what I can see in the terminal (pio):
D: Starting ESP32-radio running on CPU 1 at 240 MHz. Version Thu, 31 Mar 2022 12:40:00 GMT. Free memory 309424
D: Display type is BLUETFT
D: Partition nvs found, 20480 bytes
D: Read 32 keys from NVS
D: pin_ir set to 35
D: pin_enc_clk set to 25
D: pin_enc_dt set to 26
D: pin_enc_sw set to 27
D: pin_tft_cs set to 15
D: pin_tft_dc set to 2
D: pin_tft_scl set to -1
D: pin_tft_sda set to -1
D: pin_tft_bl set to -1
D: pin_tft_blx set to -1
D: pin_sd_cs set to 21
D: pin_ch376_cs set to -1
D: pin_ch376_int set to -1
D: pin_vs_cs set to 5
D: pin_vs_dcs set to 32
D: pin_vs_dreq set to 4
D: pin_shutdown set to -1
D: pin_shutdownx set to -1
D: pin_spi_sck set to 18
D: pin_spi_miso set to 19
D: pin_spi_mosi set to 23
D: GPIO0 is HIGH
D: GPIO2 is LOW, probably no PULL-UP
D: GPIO4 is LOW, probably no PULL-UP
D: GPIO5 is HIGH
D: GPIO12 is HIGH
D: GPIO13 is HIGH
D: GPIO14 is HIGH
D: GPIO15 is HIGH
D: GPIO16 is HIGH
D: GPIO17 is HIGH
D: GPIO18 is HIGH
D: GPIO19 is HIGH
D: GPIO21 is HIGH
D: GPIO22 is HIGH
D: GPIO23 is HIGH
D: GPIO25 is HIGH
D: GPIO26 is HIGH
D: GPIO27 is HIGH
D: GPIO32 is HIGH
D: GPIO33 is HIGH
D: GPIO34 is LOW, probably no PULL-UP
D: GPIO35 is LOW, probably no PULL-UP
D: GPIO39 is LOW, probably no PULL-UP
`
Any ideas? Thank you.
First of all, thank you very much for your time and support and congratulations for your magnificent software. Now that I'm done with the box, I'm having issues with the system. It's the first time I have to reinstall it because at some time it restarts and keeps rebooting or hangs forever. I suspect a hardware issue, but I would like to give it another try before tossing the esp32 into the bin. This time, while I was listening to some music, it restarted without being able to start again. This is what I can see in the terminal (pio):
`rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0018,len:4 load:0x3fff001c,len:1044 load:0x40078000,len:10124 load:0x40080400,len:5828 entry 0x400806a8
D: Starting ESP32-radio running on CPU 1 at 240 MHz. Version Thu, 31 Mar 2022 12:40:00 GMT. Free memory 309424 D: Display type is BLUETFT D: Partition nvs found, 20480 bytes D: Read 32 keys from NVS D: pin_ir set to 35 D: pin_enc_clk set to 25 D: pin_enc_dt set to 26 D: pin_enc_sw set to 27 D: pin_tft_cs set to 15 D: pin_tft_dc set to 2 D: pin_tft_scl set to -1 D: pin_tft_sda set to -1 D: pin_tft_bl set to -1 D: pin_tft_blx set to -1 D: pin_sd_cs set to 21 D: pin_ch376_cs set to -1 D: pin_ch376_int set to -1 D: pin_vs_cs set to 5 D: pin_vs_dcs set to 32 D: pin_vs_dreq set to 4 D: pin_shutdown set to -1 D: pin_shutdownx set to -1 D: pin_spi_sck set to 18 D: pin_spi_miso set to 19 D: pin_spi_mosi set to 23 D: GPIO0 is HIGH D: GPIO2 is LOW, probably no PULL-UP D: GPIO4 is LOW, probably no PULL-UP D: GPIO5 is HIGH D: GPIO12 is HIGH D: GPIO13 is HIGH D: GPIO14 is HIGH D: GPIO15 is HIGH D: GPIO16 is HIGH D: GPIO17 is HIGH D: GPIO18 is HIGH D: GPIO19 is HIGH D: GPIO21 is HIGH D: GPIO22 is HIGH D: GPIO23 is HIGH D: GPIO25 is HIGH D: GPIO26 is HIGH D: GPIO27 is HIGH D: GPIO32 is HIGH D: GPIO33 is HIGH D: GPIO34 is LOW, probably no PULL-UP D: GPIO35 is LOW, probably no PULL-UP D: GPIO39 is LOW, probably no PULL-UP ` Any ideas? Thank you.