Closed sermayoral closed 3 years ago
Correct received data: 99.99% updated yesterday
Almost sure , that it is just coincident ( To be sure you can go back to 0,6 and check if that possible for you ofcourse).
@sermayoral what kind of board you have ?
I had some isue with Correct received data , with sudenly also droped this parameter to 55% level. Tried to exchange ESP12 on that PCB , but it was even worse. But when i exchange to oginal again worked good.... Looks like i made a reflow of ESP8266EX chip and that helpd.
Thank you guys.
I have a Wemos D1 Mini. I am in a trip, so I dont want to test anything right now, i will try in a few days.
Maybe the flash went wrong, I had a strange thing. When i have updated to 1.0, I lost my wifi and mqtt credentials, so I had to connect to the Heishamon AP in order to enter these data again. I have never had to introduce credencials again after an update. Maybe something went wrong in this last update procedure
There is a warning in Readme that after flashing to v.1 all credentials will gone (becouse of changing file system) ,so nothing surprising here. But if you can , wipe your Wemos flash (even twice) ,and flash again with v.1 directly. Becouse I had observed this isues with lover Correct Received Data also during testing betas ,when file system was changed.... Maybe it is coincident ,or maybe have something common....
@MiG-41 thanks. I didnt see the Readme, my fault. So credentials is normal to be reset.
How can i wipe my wemos flash? Do you mean doing a hard reset with an USB cable and flashing a clean firmware?
To be honest , i don't know solution to bring back good Correct Received Data. Very first thing could be go back to v0.6 ,and see if there is ok. Then Hard reset via USB ( some flashing programs like Tasmotizer has Erase option before flashing) , with flashing v.1.0.
Then recheck all connections ,especially this ,with is connected to TX and RX of serial communication. ( But also power supply is important).
What i think , with helped me was a heat gun and reflowing of ESP8266EX chip under metal case. But this is only last solution , with i'm not sure.
Usually ESP flashers have that functionality, to clean whole flash.
Thanks guys, when i come back home from holidays I will check all your advices ☺️.
Guys, First of all I have done a Factory Reset maintaining the same version (1.0) without success. After some hours, the correct received data fell to 30%.
Second test, I have reflashed the Wemos D1 by OTA with the 1.0 version again. Same result :-(
Tomorrow i will try to flash by OTA the 0.9b version to see what happen. I keep you informed
Thanks!!
Do you have any resultsy with 0.9b?
Do you have any resultsy with 0.9b?
@geduxas sorry, I have been busy. It has snowed a lot in Madrid...
I have just flashed the 0.8b by OTA. At the moment 100 % of correct received data:
I think in the 1.0, it would have already dropped below 40. However, I will leave it a few hours to see its behavior, and I inform you
Guys, after 3 hours using 0.8b version, correct received data is above 95% (as usual before 1.0 in my case):
What do you think? Maybe its required to do a full erase of the wemos and flash it using a USB cable instead of using OTA. Its difficult to me doing it because a have a monobloc unit outside and the wemos is inside the unit. I have to wait until the snow has gone to try this.
Generally it should not have aany influence on this ,communication is not changed. Uou can try to upgrade firmware using a "bridge soft", like tasmota-minimal (from that one it is posible to upgrade any firmware ,from "normal" tasmota sometimes it is not posible). So first tasmota-minimal , then once again HeishaMon v.1. Maybe this flush somhow flash...
Generally it should not have aany influence on this ,communication is not changed. Uou can try to upgrade firmware using a "bridge soft", like tasmota-minimal (from that one it is posible to upgrade any firmware ,from "normal" tasmota sometimes it is not posible). So first tasmota-minimal , then once again HeishaMon v.1. Maybe this flush somhow flash...
Thanks @MiG-41.
I have flashed with tasmota-minimal, and an AP "ESP-XXXXXX" has appeared. I can connect to this AP, but i cannot resolve the IP 192.168.4.1, so i don't know how to proceed. Any idea?
EDIT: I think i have got bad luck: https://github.com/arendst/Tasmota/issues/5743
Looks like everything is going bad .... Maybe you are able to switch power off and then on ( as it is described there). Finally you need to climb to your HP...
Looks like everything is going bad .... Maybe you are able to switch power off and then on ( as it is described there). Finally you need to climb to your HP...
I'm climbing right now...
Hi guys.
After erasing the firmware twice and flashing the 1.0 version using an USB cable, i have better results:
In the previous attemp, I'm pretty sure i would have 30%. I don't know why i don't have more than 95% as usual in previous versions, but i think above 90% is acceptable.
Good that helps now , but i'm almost sure ,that it is not the case of HeishaMon version , but some hardware issues ( like cold solderings , not touching connector , or even esp12 on the wemos. Observe it .
I've been running v1.0 since its release and it has been absolutely as stable as the versions before:
Thanks @kenzodeluxe
It could be my board. It can have cold solderings or something like that, i'm not an expert soldering.
The stranger thing was the 30's %. After a full erase and flashing again, i get this data:
Wifi signal: 66% Memory free: 67% Correct received data: 92.21% Uptime: 1 day 2 hours 20 minutes 23 seconds
I'm seeing all data are right, so I assume its confidable, valid for me :-)
Generally it should not have aany influence on this ,communication is not changed. Uou can try to upgrade firmware using a "bridge soft", like tasmota-minimal (from that one it is posible to upgrade any firmware ,from "normal" tasmota sometimes it is not posible). So first tasmota-minimal , then once again HeishaMon v.1. Maybe this flush somhow flash...
Thanks @MiG-41.
I have flashed with tasmota-minimal, and an AP "ESP-XXXXXX" has appeared. I can connect to this AP, but i cannot resolve the IP 192.168.4.1, so i don't know how to proceed. Any idea?
EDIT: I think i have got bad luck: arendst/Tasmota#5743
Should be tasmota-litle , minimal has no setup page.... Sorry for that.
Everything is working well after the second flash will full erase. Thanks!!
Hi friends. I have using heishamon since 0.6 perfectly. The correct received data were always above 95%.
After upgrading to 1.0, I have a correct received data of 36.73%.
Are you experiencing something similar??