"Not have the sensor driver!!!" on regular dafang with original firmware_

olskar commented 6 years ago

Xiaomi Dafang
the Xiaomi-Dafang-Hacks commitid (from git log) you are experiencing the issue with:

Description

I put demo_5.5.1.177.bin on my sdcard as demo.bin and flashed it with setup button, on the serialoutput I see below error messages, any idea?

What did you do to debug the issue

`

U-Boot SPL 2013.07 (Jul 28 2017 - 17:10:01) pll_init:365 l2cache_clk = 375000000 pll_cfg.pdiv = 8, pll_cfg.h2div = 4, pll_cfg.h0div = 4, pll_cfg.cdiv = 1, pll_cfg.l2div = 3 nf=36 nr = 1 od0 = 1 od1 = 1 cppcr is 02404900 CPM_CPAPCR 0470890d nf=42 nr = 1 od0 = 1 od1 = 1 cppcr is 02a04900 CPM_CPMPCR 07d0c90d nf=50 nr = 1 od0 = 1 od1 = 1 cppcr is 03204900 CPM_CPVPCR 0320490d cppcr 0x9a794410 apll_freq 860160000 mpll_freq 1000000000 vpll_freq = 1200000000 ddr sel mpll, cpu sel apll ddrfreq 500000000 cclk 860160000 l2clk 286720000 h0clk 250000000 h2clk 250000000 pclk 125000000 DDRC_DLP:0000f003

U-Boot 2013.07 (Jul 28 2017 - 17:10:01)

Board: ISVP (Ingenic XBurst T20 SoC) DRAM: 128 MiB Top of RAM usable for U-Boot at: 84000000 Reserving 399k for U-Boot at: 83f9c000 Reserving 32784k for malloc() at: 81f98000 Reserving 32 Bytes for Board Info at: 81f97fe0 Reserving 124 Bytes for Global Data at: 81f97f64 Reserving 128k for boot params() at: 81f77f64 Stack Pointer at: 81f77f48 Now running in RAM - U-Boot at: 83f9c000 MMC: msc: 0 the manufacturer c8 SF: Detected GD25Q128

*** Warning - bad CRC, using default environment

In: serial Out: serial Err: serial misc_init_r before change the yellow_gpio gpio_request lable = yellow_gpio gpio = 38 misc_init_r after gpio_request the yellow_gpio ret is 38 mi U-Boot SPL 2013.07 (Jul 28 2017 - 17:10:01) pll_init:365 l2cache_clk = 375000000 pll_cfg.pdiv = 8, pll_cfg.h2div = 4, pll_cfg.h0div = 4, pll_cfg.cdiv = 1, pll_cfg.l2div = 3 nf=36 nr = 1 od0 = 1 od1 = 1 cppcr is 02404900 CPM_CPAPCR 0470890d nf=42 nr = 1 od0 = 1 od1 = 1 cppcr is 02a04900 CPM_CPMPCR 07d0c90d nf=50 nr = 1 od0 = 1 od1 = 1 cppcr is 03204900 CPM_CPVPCR 0320490d cppcr 0x9a794410 apll_freq 860160000 mpll_freq 1000000000 vpll_freq = 1200000000 ddr sel mpll, cpu sel apll ddrfreq 500000000 cclk 860160000 l2clk 286720000 h0clk 250000000 h2clk 250000000 pclk 125000000 DDRC_DLP:0000f003

U-Boot 2013.07 (Jul 28 2017 - 17:10:01)

Board: ISVP (Ingenic XBurst T20 SoC) DRAM: 128 MiB Top of RAM usable for U-Boot at: 84000000 Reserving 399k for U-Boot at: 83f9c000 Reserving 32784k for malloc() at: 81f98000 Reserving 32 Bytes for Board Info at: 81f97fe0 Reserving 124 Bytes for Global Data at: 81f97f64 Reserving 128k for boot params() at: 81f77f64 Stack Pointer at: 81f77f48 Now running in RAM - U-Boot at: 83f9c000 MMC: msc: 0 the manufacturer c8 SF: Detected GD25Q128

*** Warning - bad CRC, using default environment

In: serial Out: serial Err: serial misc_init_r before change the yellow_gpio gpio_request lable = yellow_gpio gpio = 38 misc_init_r after gpio_request the yellow_gpio ret is 38 misc_init_r after change the yellow_gpio ret is 0 misc_init_r before change the blue_gpio gpio_request lable = blue_gpio gpio = 39 misc_init_r after gpio_request the blue_gpio ret is 39 misc_init_r after change the blue_gpio ret is 1 gpio_request lable = night_gpio gpio = 81 misc_init_r after gpio_request the night_gpio ret is 81 misc_init_r after change the night_gpio ret is 0 gpio_request lable = night_gpio gpio = 25 misc_init_r after gpio_request the night_gpio ret is 25 misc_init_r after change the night_gpio ret is 0 gpio_request lable = night_gpio gpio = 49 misc_init_r after gpio_request the night_gpio ret is 49 misc_init_r after change the night_gpio ret is 0 gpio_request lable = USB_able_gpio gpio = 47 misc_init_r after gpio_request the USB_able_gpio ret is 47 misc_init_r after change the USB_able_gpio ret is 1 gpio_request lable = TF_able_gpio gpio = 43 misc_init_r after gpio_request the TF_able_gpio ret is 43 misc_init_r after change the TF_able_gpio ret is 1 gpio_request lable = SPK_able_gpio gpio = 63 misc_init_r after gpio_request the SPK_able_gpio ret is 63 misc_init_r after change the SPK_able_gpio ret is 0 gpio_request lable = SD_able_gpio gpio = 48 misc_init_r after gpio_request the SD_able_gpio ret is 48 misc_init_r after change the SD_able_gpio ret is 0 Hit any key to stop autoboot: 0 jiabo_do_auto_update!!!!!!!!!!!!!!!!!!!!!!!! gpio_request lable = sdupgrade gpio = 46 the manufacturer c8 SF: Detected GD25Q128

jiabo_update_to_flash!!!!!!!!!!!!!!!!!!!!!!!! jiabo_au_do_update!!!!!!!!!!!!!!!!!!!!!!!! start=0 start=40000 len=40000 flash check read... FWGRADEUP not find !!!!!!!!! gradeup check fail!!!!!!!!!!!!!!!!!!! the manufacturer c8 SF: Detected GD25Q128

Erasing SPI flash...addr align as 10000 ! sfc erase error the manufacturer c8 SF: Detected GD25Q128

--->probe spend 4 ms SF: 2621440 bytes @ 0x40000 Read: OK --->read spend 381 ms

Booting kernel from Legacy Image at 80600000 ...

Image Name: Linux-3.10.14 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1806186 Bytes = 1.7 MiB Load Address: 80010000 Entry Point: 803e3aa0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.14 (root@ubuntu) (gcc version 4.7.2 (Ingenic r2.3.3 2016.12) ) #20 PREEMPT Wed Aug 23 17:45:28 CST 2017 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 RESET ERROR PC:7E5A2F75 [ 0.000000] CPU0 revision is: 00d00101 (Ingenic Xburst) [ 0.000000] FPU revision is: 00b70000 [ 0.000000] CCLK:860MHz L2CLK:430Mhz H0CLK:200MHz H2CLK:200Mhz PCLK:100Mhz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0051c000 @ 00010000 (usable) [ 0.000000] memory: 00034000 @ 0052c000 (usable after init) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 05700000 @ 00000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x056fffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x056fffff] [ 0.000000] Primary instruction cache 32kB, 8-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] pls check processor_id[0x00d00101],sc_jz not support! [ 0.000000] MIPS secondary cache 128kB, 8-way, linesize 32 bytes. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 22098 [ 0.000000] Kernel command line: console=ttyS1,115200n8 mem=87M@0x0 ispmem=9M@0x5700000 rmem=32M@0x6000000 init=/linuxrc rootfstype=squashfs root=/dev/mtdblock2 rw mtdparts=jz_sfc:256k(boot),2048k(kernel),3392k(root),640k(driver),4736k(appfs),2048k(backupk),640k(backupd),2048k(backupa),256k(config),256k(para),-(flag) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 82020k/89088k available (3953k kernel code, 7068k reserved, 1274k data, 208k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:418 [ 0.000000] clockevents_config_and_register success. [ 0.000024] Calibrating delay loop... 858.52 BogoMIPS (lpj=4292608) [ 0.087751] pid_max: default: 32768 minimum: 301 [ 0.092736] Mount-cache hash table entries: 512 [ 0.097836] Initializing cgroup subsys debug [ 0.102098] Initializing cgroup subsys freezer [ 0.109150] regulator-dummy: no parameters [ 0.113394] NET: Registered protocol family 16 [ 0.134990] bio: create slab at 0 [ 0.141383] jz-dma jz-dma: JZ SoC DMA initialized [ 0.146632] SCSI subsystem initialized [ 0.150568] usbcore: registered new interface driver usbfs [ 0.156142] usbcore: registered new interface driver hub [ 0.161574] usbcore: registered new device driver usb [ 0.166881] i2c-gpio i2c-gpio.1: using pins 57 (SDA) and 58 (SCL) [ 0.173085] (null): set:249 hold:250 dev=100000000 h=500 l=500 [ 0.179230] media: Linux media interface: v0.10 [ 0.183784] Linux video capture interface: v2.00 [ 0.190572] Switching to clocksource jz_clocksource [ 0.195528] cfg80211: Calling CRDA to update world regulatory domain [ 0.202602] jz-dwc2 jz-dwc2: cgu clk gate get error [ 0.207537] jz-dwc2 jz-dwc2: regulator vbus get error [ 0.212624] DWC IN OTG MODE [ 0.365876] sft id =========================off [ 0.370504] dwc2 dwc2: Keep PHY ON [ 0.373900] dwc2 dwc2: Using Buffer DMA mode [ 0.578042] dwc2 dwc2: Core Release: 3.00a [ 0.582166] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller [ 0.588495] dwc2 dwc2: new USB bus registered, assigned bus number 1 [ 0.595882] hub 1-0:1.0: USB hub found [ 0.599628] hub 1-0:1.0: 1 port detected [ 0.603784] dwc2 dwc2: DWC2 Host Initialized [ 0.608280] NET: Registered protocol family 2 [ 0.613260] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.620285] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.626766] TCP: Hash tables configured (established 1024 bind 1024) [ 0.633221] TCP: reno registered [ 0.636421] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.642374] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.648976] NET: Registered protocol family 1 [ 0.653686] RPC: Registered named UNIX socket transport module. [ 0.659619] RPC: Registered udp transport module. [ 0.664453] RPC: Registered tcp transport module. [ 0.669154] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.676194] freq_udelay_jiffys[0].max_num = 10 [ 0.680620] cpufreq udelay loops_per_jiffy [ 0.685087] dwc2 dwc2: ID PIN CHANGED! [ 0.688864] init DWC as A_HOST [ 0.691950] 12000 59885 59885
[ 0.695209] 24000 119771 119771 [ 0.698633] 60000 299428 299428 [ 0.702189] 120000 598857 598857 [ 0.705645] 200000 998095 998095 [ 0.709175] 300000 1497142 1497142
[ 0.712987] 600000 2994285 2994285
[ 0.716621] 792000 3952457 3952457
[ 0.720329] 1008000 5030400 5030400
[ 0.724150] 1200000 5988571 5988571
[ 0.733711] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.740554] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.747156] msgmni has been set to 160 [ 0.752406] io scheduler noop registered [ 0.756342] io scheduler cfq registered (default) [ 0.763057] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1 [ 0.771247] console [ttyS1] enabled, bootconsole disabled [ 0.771247] console [ttyS1] enabled, bootconsole disabled [ 0.786481] brd: module loaded [ 0.791741] loop: module loaded [ 0.796020] zram: Created 2 device(s) ... [ 0.800261] logger: created 256K log 'log_main' [ 0.805691] jz SADC driver registeres over! [ 0.811045] jz TCU driver register completed [ 0.816124] the id code = c84018, the flash name is GD25Q127C [ 0.822129] JZ SFC Controller for SFC channel 0 driver register [ 0.828295] 11 cmdlinepart partitions found on MTD device jz_sfc [ 0.834563] Creating 11 MTD partitions on "jz_sfc": [ 0.839623] 0x000000000000-0x000000040000 : "boot" [ 0.845191] 0x000000040000-0x000000240000 : "kernel" [ 0.850847] 0x000000240000-0x000000590000 : "root" [ 0.856414] 0x000000590000-0x000000630000 : "driver" [ 0.862157] 0x000000630000-0x000000ad0000 : "appfs" [ 0.867770] 0x000000ad0000-0x000000cd0000 : "backupk" [ 0.873617] 0x000000cd0000-0x000000d70000 : "backupd" [ 0.879399] 0x000000d70000-0x000000f70000 : "backupa" [ 0.885242] 0x000000f70000-0x000000fb0000 : "config" [ 0.890980] 0x000000fb0000-0x000000ff0000 : "para" [ 0.896579] 0x000000ff0000-0x000001000000 : "flag" [ 0.902117] SPI NOR MTD LOAD OK [ 0.905447] tun: Universal TUN/TAP device driver, 1.6 [ 0.910679] tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com [ 0.917249] usbcore: registered new interface driver zd1201 [ 0.923100] usbcore: registered new interface driver r8152 [ 0.928865] usbcore: registered new interface driver usb-storage [ 0.935241] usbcore: registered new interface driver usbserial [ 0.941323] usbcore: registered new interface driver usbserial_generic [ 0.948169] usbserial: USB Serial support registered for generic [ 0.954451] usbcore: registered new interface driver ch341 [ 0.960167] usbserial: USB Serial support registered for ch341-uart [ 0.966714] usbcore: registered new interface driver cp210x [ 0.972533] usbserial: USB Serial support registered for cp210x [ 0.978719] usbcore: registered new interface driver pl2303 [ 0.984543] usbserial: USB Serial support registered for pl2303 [ 1.491652] i8042: i8042 controller selftest timeout [ 1.497318] jzmmc_v1.2 jzmmc_v1.2.0: vmmc regulator missing [ 1.512000] jzmmc_v1.2 jzmmc_v1.2.0: card inserted, state=0 [ 1.542002] jzmmc_v1.2 jzmmc_v1.2.0: register success! [ 1.547380] jzmmc_v1.2 jzmmc_v1.2.1: vmmc regulator missing [ 1.592096] jzmmc_v1.2 jzmmc_v1.2.1: register success! [ 1.597586] hidraw: raw HID events driver (C) Jiri Kosina [ 1.604542] usbcore: registered new interface driver usbhid [ 1.610322] usbhid: USB HID core driver [ 1.614590] TCP: cubic registered [ 1.618032] NET: Registered protocol family 17 [ 1.623686] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 1.630843] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.642068] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.649724] Freeing unused kernel memory: 208K (8052c000 - 80560000) [ 1.795229] dwc2 dwc2: ++OTG Interrupt: A-Device Timeout Change++ mdev is ok...... [ 2.735738] wait stable.[246][cgu_msc0] [ 2.741348] mmc0: new high speed SDXC card at address aaaa [ 2.764910] mmcblk0: mmc0:aaaa SC64G 59.4 GiB [ 2.776005] mmcblk0: p1

Ingenic-uc1_1 login: [ 2.886490] register all isp device successfully! [ 2.896196] @@@@ tx-isp-probe ok @@@@@ [ 2.944040] exFAT: Version 1.2.9 [ 3.008797] jz_codec_register: probe() successful! [ 3.362397] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06 desc a0728000) [ 3.371654] dma dma0chan25: Channel 25 have been requested.(phy id 6,type 0x06 desc a0727000) [ 3.832119] RTL871X: module init start [ 3.836017] RTL871X: rtl8189es v4.3.18.3_20185.20161116_pmpinclu_mac_monitor_minMem_EDCA542B_pbyr [ 3.845315] RTL871X: build time: Aug 25 2017 09:49:30 [ 3.850563] wlan power on [ 3.872397] RTL871X: module init ret=0 [ 3.929993] mmc1: new SDIO card at address 0001 [ 3.962691] bFWReady == _FALSE call reset 8051... [ 4.002351] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=c0:6d:1a:f1:ba:36 GPIO 40 in
GPIO 26 out
GPIO 25 out
GPIO 49 out
GPIO 47 out
GPIO 48 out
GPIO 43 out
right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 right_count=3 value=0 last_value=0 not in singleboard test hello Guozhixin OKOKOKOKOKOKOKOKOKOK xxq:begin to check the sensor ty[ 7.459999] name : i2c-gpio1 nr : 1 pe [ 7.469162] name : i2c0 nr : 0 [ 7.532866] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 7.540001] i2c i2c-0: --I2C txabrt: [ 7.543725] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 7.550325] error: sensor_read,146 ret = -5 [ 7.554678] sensor_read: addr=0xa value = 0x0 [ 7.559284] err sensor read addr = 0xa, value = 0x0 [ 7.624483] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 7.631614] i2c i2c-0: --I2C txabrt: [ 7.635335] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 7.641931] error: sensor_read,146 ret = -5 [ 7.646277] sensor_read: addr=0x0 value = 0x0 [ 7.650879] err sensor read addr = 0x0, value = 0x0 [ 7.716141] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 7.723286] i2c i2c-0: --I2C txabrt: [ 7.726992] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 7.733603] error: sensor_read,146 ret = -5 [ 7.737937] sensor_read: addr=0x0 value = 0x0 [ 7.742553] err sensor read addr = 0x0, value = 0x0 [ 7.807736] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 7.814879] i2c i2c-0: --I2C txabrt: [ 7.818586] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 7.825194] error: sensor_read,146 ret = -5 [ 7.829527] sensor_read: addr=0x3107 value = 0x0 [ 7.834414] err sensor read addr = 0x3107, value = 0x0 [ 7.899869] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 7.907011] i2c i2c-0: --I2C txabrt: [ 7.910720] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 7.917330] error: sensor_read,146 ret = -5 [ 7.921664] sensor_read: addr=0x3107 value = 0x0 [ 7.926550] err sensor read addr = 0x3107, value = 0x0 [ 7.992022] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 7.999153] i2c i2c-0: --I2C txabrt: [ 8.002878] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 8.009475] error: sensor_read,146 ret = -5 [ 8.013821] sensor_read: addr=0x301c value = 0x0 [ 8.018694] err sensor read addr = 0x301c, value = 0x0 [ 8.084162] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 8.091291] i2c i2c-0: --I2C txabrt: [ 8.095009] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 8.101608] error: sensor_read,146 ret = -5 [ 8.105955] sensor_read: addr=0x301c value = 0x0 [ 8.110827] err sensor read addr = 0x301c, value = 0x0 [ 8.116192] info: failed sensor find

sensor not found

[ 8.120035] misc sinfo_release Not have the sensor driver!!!

`

EliasKotlyar commented 6 years ago

What kind of hardware do you have? Maybe you flashed the wrong firmware package?

netRunner0 commented 6 years ago

0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.14 (root@ubuntu) (gcc version 4.7.2 (Ingenic r2.3.3 2016.12) ) #21 PREEMPT Thu Oct 19 11:38:16 CST 2017 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 RESET ERROR PC:FB3E429F [ 0.000000] CPU0 revision is: 00d00101 (Ingenic Xburst) [ 0.000000] FPU revision is: 00b70000 [ 0.000000] cgu_get_rate, parent = 860160000, rate = 0, m = 0, n = 0, reg val = 0x000020ff [ 0.000000] CCLK:860MHz L2CLK:430Mhz H0CLK:200MHz H2CLK:200Mhz PCLK:100Mhz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0051b000 @ 00010000 (usable) [ 0.000000] memory: 00035000 @ 0052b000 (usable after init) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 06800000 @ 00000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x067fffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x067fffff] [ 0.000000] On node 0 totalpages: 26624 [ 0.000000] free_area_init_node: node 0, pgdat 805285f0, node_mem_map 81000000 [ 0.000000] Normal zone: 208 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 26624 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 32kB, 8-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] pls check processor_id[0x00d00101],sc_jz not support! [ 0.000000] MIPS secondary cache 128kB, 8-way, linesize 32 bytes. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 26416 [ 0.000000] Kernel command line: console=ttyS1,115200n8 mem=104M@0x0 ispmem=8M@0x6800000 rmem=16M@0x7000000 init=/linuxrc rootfstype=squashfs root=/dev/mtdblock2 rw mtdparts=jz_sfc:256k(boot),2048k(kernel),3392k(root),640k(driver),4736k(appfs),2048k(backupk),640k(backupd),2048k(backupa),256k(config),256k(para),-(flag) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 99428k/106496k available (3951k kernel code, 7068k reserved, 1276k data, 212k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:418 [ 0.000000] clockevents_config_and_register success. [ 0.000024] Calibrating delay loop... 858.52 BogoMIPS (lpj=4292608) [ 0.087752] pid_max: default: 32768 minimum: 301 [ 0.092736] Mount-cache hash table entries: 512 [ 0.097836] Initializing cgroup subsys debug [ 0.102096] Initializing cgroup subsys freezer [ 0.109148] regulator-dummy: no parameters [ 0.113392] NET: Registered protocol family 16 [ 0.134946] bio: create slab at 0 [ 0.141320] jz-dma jz-dma: JZ SoC DMA initialized [ 0.146570] SCSI subsystem initialized [ 0.150505] usbcore: registered new interface driver usbfs [ 0.156083] usbcore: registered new interface driver hub [ 0.161520] usbcore: registered new device driver usb [ 0.166822] i2c-gpio i2c-gpio.1: using pins 57 (SDA) and 58 (SCL) [ 0.173020] (null): set:249 hold:250 dev=100000000 h=500 l=500 [ 0.179165] media: Linux media interface: v0.10 [ 0.183725] Linux video capture interface: v2.00 [ 0.190508] Switching to clocksource jz_clocksource [ 0.195463] cfg80211: Calling CRDA to update world regulatory domain [ 0.202532] jz-dwc2 jz-dwc2: cgu clk gate get error [ 0.207468] jz-dwc2 jz-dwc2: regulator vbus get error [ 0.212554] DWC IN OTG MODE [ 0.365806] sft id =========================off [ 0.370404] dwc2 dwc2: Keep PHY ON [ 0.373794] dwc2 dwc2: Using Buffer DMA mode [ 0.577944] dwc2 dwc2: Core Release: 3.00a [ 0.582067] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller [ 0.588395] dwc2 dwc2: new USB bus registered, assigned bus number 1 [ 0.595802] hub 1-0:1.0: USB hub found [ 0.599548] hub 1-0:1.0: 1 port detected [ 0.603692] dwc2 dwc2: DWC2 Host Initialized [ 0.608186] NET: Registered protocol family 2 [ 0.613173] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.620200] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.626680] TCP: Hash tables configured (established 1024 bind 1024) [ 0.633136] TCP: reno registered [ 0.636333] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.642287] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.648891] NET: Registered protocol family 1 [ 0.653603] RPC: Registered named UNIX socket transport module. [ 0.659536] RPC: Registered udp transport module. [ 0.664370] RPC: Registered tcp transport module. [ 0.669071] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.676110] freq_udelay_jiffys[0].max_num = 10 [ 0.680538] cpufreq udelay loops_per_jiffy [ 0.685006] dwc2 dwc2: ID PIN CHANGED! [ 0.688783] init DWC as A_HOST [ 0.691867] 12000 59885 59885
[ 0.695129] 24000 119771 119771 [ 0.698551] 60000 299428 299428 [ 0.702105] 120000 598857 598857 [ 0.705561] 200000 998095 998095 [ 0.709093] 300000 1497142 1497142
[ 0.712907] 600000 2994285 2994285
[ 0.716539] 792000 3952457 3952457
[ 0.720247] 1008000 5030400 5030400
[ 0.724069] 1200000 5988571 5988571
[ 0.733438] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.740281] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.746881] msgmni has been set to 194 [ 0.752113] io scheduler noop registered [ 0.756049] io scheduler cfq registered (default) [ 0.762715] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1 [ 0.770905] console [ttyS1] enabled, bootconsole disabled [ 0.786123] brd: module loaded [ 0.791376] loop: module loaded [ 0.795660] zram: Created 2 device(s) ... [ 0.799896] logger: created 256K log 'log_main' [ 0.805300] jz SADC driver registeres over! [ 0.810606] jz TCU driver register completed [ 0.815705] the id code = c84018, the flash name is GD25Q127C [ 0.821666] JZ SFC Controller for SFC channel 0 driver register [ 0.827871] 11 cmdlinepart partitions found on MTD device jz_sfc [ 0.834136] Creating 11 MTD partitions on "jz_sfc": [ 0.839195] 0x000000000000-0x000000040000 : "boot" [ 0.844744] 0x000000040000-0x000000240000 : "kernel" [ 0.850411] 0x000000240000-0x000000590000 : "root" [ 0.855966] 0x000000590000-0x000000630000 : "driver" [ 0.861651] 0x000000630000-0x000000ad0000 : "appfs" [ 0.867322] 0x000000ad0000-0x000000cd0000 : "backupk" [ 0.873153] 0x000000cd0000-0x000000d70000 : "backupd" [ 0.878925] 0x000000d70000-0x000000f70000 : "backupa" [ 0.884768] 0x000000f70000-0x000000fb0000 : "config" [ 0.890496] 0x000000fb0000-0x000000ff0000 : "para" [ 0.896097] 0x000000ff0000-0x000001000000 : "flag" [ 0.901585] SPI NOR MTD LOAD OK [ 0.904964] tun: Universal TUN/TAP device driver, 1.6 [ 0.910202] tun: (C) 1999-2004 Max Krasnyansky [ 0.916748] usbcore: registered new interface driver zd1201 [ 0.922604] usbcore: registered new interface driver r8152 [ 0.928371] usbcore: registered new interface driver usb-storage [ 0.934755] usbcore: registered new interface driver usbserial [ 0.940836] usbcore: registered new interface driver usbserial_generic [ 0.947667] usbserial: USB Serial support registered for generic [ 0.953946] usbcore: registered new interface driver ch341 [ 0.959661] usbserial: USB Serial support registered for ch341-uart [ 0.966205] usbcore: registered new interface driver cp210x [ 0.972035] usbserial: USB Serial support registered for cp210x [ 0.978214] usbcore: registered new interface driver pl2303 [ 0.984039] usbserial: USB Serial support registered for pl2303 [ 1.491138] i8042: i8042 controller selftest timeout [ 1.496802] jzmmc_v1.2 jzmmc_v1.2.0: vmmc regulator missing [ 1.511925] jzmmc_v1.2 jzmmc_v1.2.0: card inserted, state=0 [ 1.541927] jzmmc_v1.2 jzmmc_v1.2.0: register success! [ 1.547316] jzmmc_v1.2 jzmmc_v1.2.1: vmmc regulator missing [ 1.592021] jzmmc_v1.2 jzmmc_v1.2.1: register success! [ 1.597496] hidraw: raw HID events driver (C) Jiri Kosina [ 1.604460] usbcore: registered new interface driver usbhid [ 1.610236] usbhid: USB HID core driver [ 1.614512] TCP: cubic registered [ 1.617951] NET: Registered protocol family 17 [ 1.623609] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 1.630758] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.642902] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.650560] Freeing unused kernel memory: 212K (8052b000 - 80560000) [ 1.794864] dwc2 dwc2: ++OTG Interrupt: A-Device Timeout Change++ [ 2.811208] mmc0: new SD card at address aaaa [ 2.819194] mmcblk0: mmc0:aaaa SU02G 1.84 GiB [ 2.825890] mmcblk0: p1 [ 3.062409] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 4.680928] RTL871X: module init start [ 4.686936] RTL871X: rtl8189es v4.3.18.3_20185.20161116_pmpinclu_mac_monitor_minMem_EDCA542B_pbyr [ 4.696219] RTL871X: build time: Oct 19 2017 11:54:52 [ 4.701462] wlan power on [ 4.722486] RTL871X: module init ret=0 [ 4.780242] mmc1: new SDIO card at address 0001 [ 4.806156] bFWReady == _FALSE call reset 8051... [ 4.842256] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=78:11:dc:70:fa:e3 [ 6.602088] ==> rtl8188e_iol_efuse_patch [ 8.301123] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008 [ 8.447532] RTL871X: start auth [ 8.481970] RTL871X: auth success, start assoc [ 8.537552] RTL871X: assoc success [ 8.690850] RTL871X: recv eapol packet [ 8.697772] RTL871X: send eapol packet [ 8.710030] RTL871X: recv eapol packet [ 8.716762] RTL871X: send eapol packet [ 8.724266] RTL871X: set pairwise key camid:4, addr:58:8b:f3:65:86:60, kid:0, type:AES [ 8.736750] RTL871X: set group key camid:5, addr:58:8b:f3:65:86:60, kid:1, type:TKIP [ 10.841119] request spk en gpio 63 ok! [ 10.841135] jz_codec_register: probe() successful! [ 10.850289] cgu_set_rate, parent = 860160000, rate = 2048000, n = 420, reg val = 0x000021a4 [ 10.850307] cgu_enable,cgu_i2s reg val = 0x200021a4 [ 11.192314] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06 desc a57b1000) [ 11.201574] dma dma0chan25: Channel 25 have been requested.(phy id 6,type 0x06 desc a578c000) [ 12.255611] motor_probe743 [ 12.274086] name : i2c-gpio1 nr : 1 [ 12.277708] name : i2c0 nr : 0 [ 12.343987] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 12.351125] i2c i2c-0: --I2C txabrt: [ 12.354854] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 12.361454] error: sensor_read,172 ret = -5 [ 12.365801] sensor_read: addr=0xa value = 0x0 [ 12.370404] err sensor read addr = 0xa, value = 0x0 [ 12.436355] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 12.443563] i2c i2c-0: --I2C txabrt: [ 12.447375] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 12.454089] error: sensor_read,172 ret = -5 [ 12.458531] sensor_read: addr=0x300a value = 0x0 [ 12.463536] err sensor read addr = 0x300a, value = 0x0 [ 12.529100] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 12.536251] i2c i2c-0: --I2C txabrt: [ 12.539962] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 12.546634] error: sensor_read,172 ret = -5 [ 12.551048] sensor_read: addr=0x300b value = 0x0 [ 12.555950] err sensor read addr = 0x300b, value = 0x0 [ 12.621416] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 12.628561] i2c i2c-0: --I2C txabrt: [ 12.632283] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 12.638880] error: sensor_read,172 ret = -5 [ 12.643227] sensor_read: addr=0xa value = 0x0 [ 12.647892] err sensor read addr = 0xa, value = 0x0 [ 12.713422] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 12.720558] i2c i2c-0: --I2C txabrt: [ 12.724281] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 12.730879] error: sensor_read,172 ret = -5 [ 12.735225] sensor_read: addr=0x580b value = 0x0 [ 12.740134] err sensor read addr = 0x580b, value = 0x0 [ 12.805786] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 12.812935] i2c i2c-0: --I2C txabrt: [ 12.816644] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 12.823252] error: sensor_read,172 ret = -5 [ 12.827586] sensor_read: addr=0x580b value = 0x0 [ 12.832473] err sensor read addr = 0x580b, value = 0x0 [ 12.899170] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 12.906617] i2c i2c-0: --I2C txabrt: [ 12.910334] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 12.916970] error: sensor_read,172 ret = -5 [ 12.921306] sensor_read: addr=0x3107 value = 0x0 [ 12.926196] err sensor read addr = 0x3107, value = 0x0 [ 12.993012] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.000153] i2c i2c-0: --I2C txabrt: [ 13.003902] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.010505] error: sensor_read,172 ret = -5 [ 13.014861] sensor_read: addr=0x3107 value = 0x0 [ 13.019737] err sensor read addr = 0x3107, value = 0x0 [ 13.085567] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.092717] i2c i2c-0: --I2C txabrt: [ 13.096424] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.103034] error: sensor_read,172 ret = -5 [ 13.107369] sensor_read: addr=0x3000 value = 0x0 [ 13.112255] err sensor read addr = 0x3000, value = 0x0 [ 13.178249] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.185397] i2c i2c-0: --I2C txabrt: [ 13.189108] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.195718] error: sensor_read,172 ret = -5 [ 13.200051] sensor_read: addr=0xa value = 0x0 [ 13.204668] err sensor read addr = 0xa, value = 0x0 [ 13.270149] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.277372] i2c i2c-0: --I2C txabrt: [ 13.281176] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.287800] error: sensor_read,172 ret = -5 [ 13.292148] sensor_read: addr=0xf0 value = 0x0 [ 13.296843] err sensor read addr = 0xf0, value = 0x0 [ 13.362139] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.369331] i2c i2c-0: --I2C txabrt: [ 13.373137] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.379739] error: sensor_read,172 ret = -5 [ 13.384095] sensor_read: addr=0xf0 value = 0x0 [ 13.388788] err sensor read addr = 0xf0, value = 0x0 [ 13.454079] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.461212] i2c i2c-0: --I2C txabrt: [ 13.464990] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.471665] error: sensor_read,172 ret = -5 [ 13.476021] sensor_read: addr=0xf0 value = 0x0 [ 13.480713] err sensor read addr = 0xf0, value = 0x0 [ 13.546003] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.553149] i2c i2c-0: --I2C txabrt: [ 13.556857] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.563467] error: sensor_read,172 ret = -5 [ 13.567801] sensor_read: addr=0xfc value = 0x0 [ 13.572565] err sensor read addr = 0xfc, value = 0x0 [ 13.638207] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.645355] i2c i2c-0: --I2C txabrt: [ 13.649063] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.655674] error: sensor_read,172 ret = -5 [ 13.660008] sensor_read: addr=0x3004 value = 0x0 [ 13.664893] err sensor read addr = 0x3004, value = 0x0 [ 13.730576] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.737726] i2c i2c-0: --I2C txabrt: [ 13.741436] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.748050] error: sensor_read,172 ret = -5 [ 13.752409] sensor_read: addr=0x300a value = 0x0 [ 13.757283] err sensor read addr = 0x300a, value = 0x0 [ 13.822928] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.830064] i2c i2c-0: --I2C txabrt: [ 13.833789] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.840386] error: sensor_read,172 ret = -5 [ 13.844734] sensor_read: addr=0x31f3 value = 0x0 [ 13.849609] err sensor read addr = 0x31f3, value = 0x0 [ 13.915230] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 13.922377] i2c i2c-0: --I2C txabrt: [ 13.926086] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 13.932697] error: sensor_read,172 ret = -5 [ 13.937031] sensor_read: addr=0x3107 value = 0x0 [ 13.941919] err sensor read addr = 0x3107, value = 0x0 [ 14.007647] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 14.014795] i2c i2c-0: --I2C txabrt: [ 14.018502] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 14.025116] error: sensor_read,172 ret = -5 [ 14.029448] sensor_read: addr=0x4 value = 0x0 [ 14.034066] err sensor read addr = 0x4, value = 0x0 [ 14.099884] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 14.107036] i2c i2c-0: --I2C txabrt: [ 14.110744] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 14.117354] error: sensor_read,172 ret = -5 [ 14.121688] sensor_read: addr=0xa value = 0x0 [ 14.126304] err sensor read addr = 0xa, value = 0x0 [ 14.191753] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 14.198966] i2c i2c-0: --I2C txabrt: [ 14.202765] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 14.209367] error: sensor_read,172 ret = -5 [ 14.213720] sensor_read: addr=0x0 value = 0x0 [ 14.218327] err sensor read addr = 0x0, value = 0x0 [ 14.283530] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 14.290721] i2c i2c-0: --I2C txabrt: [ 14.294540] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 14.301338] error: sensor_read,172 ret = -5 [ 14.305773] sensor_read: addr=0x300a value = 0x0 [ 14.310650] err sensor read addr = 0x300a, value = 0x0 [ 14.376172] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 14.383321] i2c i2c-0: --I2C txabrt: [ 14.387029] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 14.393707] error: sensor_read,172 ret = -5 [ 14.398143] sensor_read: addr=0xa value = 0x0 [ 14.402874] err sensor read addr = 0xa, value = 0x0 [ 14.468177] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 14.475324] i2c i2c-0: --I2C txabrt: [ 14.479032] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 14.485643] error: sensor_read,172 ret = -5 [ 14.490039] sensor_read: addr=0x31f3 value = 0x0 [ 14.495025] err sensor read addr = 0x31f3, value = 0x0 [ 14.560781] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt [ 14.567929] i2c i2c-0: --I2C txabrt: [ 14.571637] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK [ 14.578247] error: sensor_read,172 ret = -5

olskar commented 6 years ago

@EliasKotlyar as far as I know i have the regular dafang, using https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/blob/master/firmware_original/dafang/demo_5.5.1.177.bin

celbel commented 5 years ago

**I have two older Wyze Cam v2 that take the cfw-1.1.bin firmware no problem. Just bought the Wyze Cam v2 "3 Cam" special and now having exact same issues as above with new cameras.

Found the following images from Wyze work:

Wyze Cam v2 Firmware V4.9.3.64 (Release date: December 13, 2018)
Wyze Cam v2 Firmware V4.9.2.52 (Release date: October 22, 2018)
Wyze Cam v2 Firmware V4.9.2.42 (Release date: September 17, 2018)

Any firmware version dated prior to those listed above exhibit the same problem as previous posters. Rear circuit board shows date stamp of "2018-09-03". Any suggestions?

Here's a dump of the console output when attempting to load cfw-1.1.bin:**

U-Boot SPL 2013.07 (Jul 05 2018 - 13:33:27)
pll_init:365
l2cache_clk = 375000000
pll_cfg.pdiv = 8, pll_cfg.h2div = 4, pll_cfg.h0div = 4, pll_cfg.cdiv = 1, pll_cfg.l2div = 3
nf=36 nr = 1 od0 = 1 od1 = 1
cppcr is 02404900
CPM_CPAPCR 0470890d
nf=42 nr = 1 od0 = 1 od1 = 1
cppcr is 02a04900
CPM_CPMPCR 07d0c90d
nf=50 nr = 1 od0 = 1 od1 = 1
cppcr is 03204900
CPM_CPVPCR 0320490d
cppcr 0x9a794410
apll_freq 860160000 
mpll_freq 1000000000 
vpll_freq = 1200000000
ddr sel mpll, cpu sel apll
ddrfreq 500000000
cclk  860160000
l2clk 286720000
h0clk 250000000
h2clk 250000000
pclk  125000000
DDRC_DLP:0000f003

U-Boot 2013.07 (Jul 05 2018 - 13:33:27)

Board: ISVP (Ingenic XBurst T20 SoC)
DRAM:  128 MiB
Top of RAM usable for U-Boot at: 84000000
Reserving 399k for U-Boot at: 83f9c000
Reserving 32784k for malloc() at: 81f98000
Reserving 32 Bytes for Board Info at: 81f97fe0
Reserving 124 Bytes for Global Data at: 81f97f64
Reserving 128k for boot params() at: 81f77f64
Stack Pointer at: 81f77f48
Now running in RAM - U-Boot at: 83f9c000
MMC:   msc: 0
the manufacturer c8
SF: Detected GD25Q128

*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
misc_init_r before change the wifi_enable_gpio
gpio_request lable = wifi_enable_gpio gpio = 62
misc_init_r after gpio_request the wifi_enable_gpio ret is 62
misc_init_r after change the wifi_enable_gpio ret is 0
misc_init_r before change the yellow_gpio
gpio_request lable = yellow_gpio gpio = 38
misc_init_r after gpio_request the yellow_gpio ret is 38
misc_init_r after change the yellow_gpio ret is 0
misc_init_r before change the blue_gpio
gpio_request lable = blue_gpio gpio = 39
misc_init_r after gpio_request the blue_gpio ret is 39
misc_init_r after change the blue_gpio ret is 1
gpio_request lable = night_gpio gpio = 81
misc_init_r after gpio_request the night_gpio ret is 81
misc_init_r after change the night_gpio ret is 0
gpio_request lable = night_gpio gpio = 25
misc_init_r after gpio_request the night_gpio ret is 25
misc_init_r after change the night_gpio ret is 0
gpio_request lable = night_gpio gpio = 49
misc_init_r after gpio_request the night_gpio ret is 49
misc_init_r after change the night_gpio ret is 0
gpio_request lable = USB_able_gpio gpio = 47
misc_init_r after gpio_request the USB_able_gpio ret is 47
misc_init_r after change the USB_able_gpio ret is 0
gpio_request lable = TF_able_gpio gpio = 43
misc_init_r after gpio_request the TF_able_gpio ret is 43
misc_init_r after change the TF_able_gpio ret is 1
gpio_request lable = SPK_able_gpio gpio = 63
misc_init_r after gpio_request the SPK_able_gpio ret is 63
misc_init_r after change the SPK_able_gpio ret is 0
gpio_request lable = SD_able_gpio gpio = 48
misc_init_r after gpio_request the SD_able_gpio ret is 48
misc_init_r after change the SD_able_gpio ret is 0
misc_init_r before change the wifi_enable_gpio
gpio_request lable = wifi_enable_gpio gpio = 62
misc_init_r after gpio_request the wifi_enable_gpio ret is 62
misc_init_r after change the wifi_enable_gpio ret is 1
Hit any key to stop autoboot:  0 
jiabo_do_auto_update!!!!!!!!!!!!!!!!!!!!!!!!
gpio_request lable = sdupgrade gpio = 46
setup_button set long!!!!!!!!!!!!!!!!!!!
Interface:  MMC
  Device 0: Vendor: Man 000002 Snr 00013900 Rev: 9.12 Prod: SA02G
            Type: Removable Hard Disk
            Capacity: 1876.0 MB = 1.8 GB (3842048 x 512)
Filesystem: FAT32 "           "
the manufacturer c8
SF: Detected GD25Q128

reading demo.bin
reading demo.bin
jiabo_au_check_cksum_valid!!!!!!!!!!!!!!!!!!!!!!!!
jiabo_idx=4
misc_init_r before change the blue_gpio
gpio_request lable = blue_gpio gpio = 39
misc_init_r after gpio_request the blue_gpio ret is 39
misc_init_r after change the blue_gpio ret is 0
jiabo_start=40000,jiabo_len=a90000
flash erase...
flash write...
misc_init_r after change the blue_gpio ret is 1
the manufacturer c8
SF: Detected GD25Q128

--->probe spend 4 ms
SF: 2621440 bytes @ 0x40000 Read: OK
--->read spend 381 ms
## Booting kernel from Legacy Image at 80600000 ...
   Image Name:   Linux-3.10.14
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1839359 Bytes = 1.8 MiB
   Load Address: 80010000
   Entry Point:  803f51f0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.14 (root@ubuntu) (gcc version 4.7.2 (Ingenic r2.3.3 2016.12) ) #21 PREEMPT Thu Oct 19 11:38:16 CST 2017
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 RESET ERROR PC:21302C22
[    0.000000] CPU0 revision is: 00d00101 (Ingenic Xburst)
[    0.000000] FPU revision is: 00b70000
[    0.000000] CCLK:860MHz L2CLK:430Mhz H0CLK:200MHz H2CLK:200Mhz PCLK:100Mhz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 00535000 @ 00010000 (usable)
[    0.000000]  memory: 0003b000 @ 00545000 (usable after init)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 06800000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x067fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x067fffff]
[    0.000000] Primary instruction cache 32kB, 8-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] pls check processor_id[0x00d00101],sc_jz not support!
[    0.000000] MIPS secondary cache 128kB, 8-way, linesize 32 bytes.
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 26416
[    0.000000] Kernel command line: console=ttyS1,115200n8 mem=104M@0x0 ispmem=8M@0x6800000 rmem=16M@0x7000000 init=/linuxrc rootfstype=squashfs root=/dev/mtdblock2 rw mtdparts=jz_sfc:256k(boot),2048k(kernel),3392k(root),640k(driver),4736k(appfs),2048k(backupk),640k(backupd),2048k(backupa),256k(config),256k(para),-(flag)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 99300k/106496k available (4024k kernel code, 7196k reserved, 1304k data, 236k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:418
[    0.000000] clockevents_config_and_register success.
[    0.000024] Calibrating delay loop... 858.52 BogoMIPS (lpj=4292608)
[    0.087753] pid_max: default: 32768 minimum: 301
[    0.092738] Mount-cache hash table entries: 512
[    0.097839] Initializing cgroup subsys debug
[    0.102100] Initializing cgroup subsys freezer
[    0.109174] regulator-dummy: no parameters
[    0.113464] NET: Registered protocol family 16
[    0.135465] bio: create slab <bio-0> at 0
[    0.141794] jz-dma jz-dma: JZ SoC DMA initialized
[    0.147054] SCSI subsystem initialized
[    0.150986] usbcore: registered new interface driver usbfs
[    0.156558] usbcore: registered new interface driver hub
[    0.161993] usbcore: registered new device driver usb
[    0.167294] i2c-gpio i2c-gpio.1: using pins 57 (SDA) and 58 (SCL)
[    0.173502]  (null): set:249  hold:250 dev=100000000 h=500 l=500
[    0.179650] media: Linux media interface: v0.10
[    0.184203] Linux video capture interface: v2.00
[    0.191009] Switching to clocksource jz_clocksource
[    0.195964] cfg80211: Calling CRDA to update world regulatory domain
[    0.203042] jz-dwc2 jz-dwc2: cgu clk gate get error
[    0.207978] jz-dwc2 jz-dwc2: regulator vbus get error
[    0.213064] DWC IN OTG MODE
[    0.366317] sft id =========================off
[    0.370934] dwc2 dwc2: Keep PHY ON
[    0.374326] dwc2 dwc2: Using Buffer DMA mode
[    0.578473] dwc2 dwc2: Core Release: 3.00a
[    0.582596] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller
[    0.588926] dwc2 dwc2: new USB bus registered, assigned bus number 1
[    0.596316] hub 1-0:1.0: USB hub found
[    0.600056] hub 1-0:1.0: 1 port detected
[    0.604218] dwc2 dwc2: DWC2 Host Initialized
[    0.608714] NET: Registered protocol family 2
[    0.613691] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.620718] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.627197] TCP: Hash tables configured (established 1024 bind 1024)
[    0.633651] TCP: reno registered
[    0.636849] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.642804] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.649405] NET: Registered protocol family 1
[    0.654120] RPC: Registered named UNIX socket transport module.
[    0.660053] RPC: Registered udp transport module.
[    0.664888] RPC: Registered tcp transport module.
[    0.669588] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.676632] freq_udelay_jiffys[0].max_num = 10
[    0.681060] cpufreq  udelay  loops_per_jiffy 
[    0.685525] dwc2 dwc2: ID PIN CHANGED!
[    0.689303] init DWC as A_HOST
[    0.692407] 12000     59885   59885  
[    0.695629] 24000     119771  119771 
[    0.699072] 60000     299428  299428 
[    0.702707] 120000    598857  598857 
[    0.706163] 200000    998095  998095 
[    0.709695] 300000    1497142     1497142    
[    0.713437] 600000    2994285     2994285    
[    0.717111] 792000    3952457     3952457    
[    0.720819] 1008000   5030400     5030400    
[    0.724629] 1200000   5988571     5988571    
[    0.734015] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.740856] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.747459] msgmni has been set to 193
[    0.752699] io scheduler noop registered
[    0.756635] io scheduler cfq registered (default)
[    0.763307] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1
[    0.771497] console [ttyS1] enabled, bootconsole disabled
[    0.771497] console [ttyS1] enabled, bootconsole disabled
[    0.786715] brd: module loaded
[    0.791980] loop: module loaded
[    0.796128] zram: Created 2 device(s) ...
[    0.800368] logger: created 256K log 'log_main'
[    0.805775] jz SADC driver registeres over!
[    0.811089] jz TCU driver register completed
[    0.816333] the id code = c84018, the flash name is GD25Q127C
[    0.822299] JZ SFC Controller for SFC channel 0 driver register
[    0.828503] 11 cmdlinepart partitions found on MTD device jz_sfc
[    0.834766] Creating 11 MTD partitions on "jz_sfc":
[    0.839824] 0x000000000000-0x000000040000 : "boot"
[    0.845381] 0x000000040000-0x000000240000 : "kernel"
[    0.851039] 0x000000240000-0x000000590000 : "root"
[    0.856599] 0x000000590000-0x000000630000 : "driver"
[    0.862293] 0x000000630000-0x000000ad0000 : "appfs"
[    0.867963] 0x000000ad0000-0x000000cd0000 : "backupk"
[    0.873785] 0x000000cd0000-0x000000d70000 : "backupd"
[    0.879565] 0x000000d70000-0x000000f70000 : "backupa"
[    0.885412] 0x000000f70000-0x000000fb0000 : "config"
[    0.891149] 0x000000fb0000-0x000000ff0000 : "para"
[    0.896752] 0x000000ff0000-0x000001000000 : "flag"
[    0.902232] SPI NOR MTD LOAD OK
[    0.905605] tun: Universal TUN/TAP device driver, 1.6
[    0.910840] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.917399] usbcore: registered new interface driver zd1201
[    0.923247] usbcore: registered new interface driver r8152
[    0.929019] usbcore: registered new interface driver usb-storage
[    0.935398] usbcore: registered new interface driver usbserial
[    0.941480] usbcore: registered new interface driver usbserial_generic
[    0.948313] usbserial: USB Serial support registered for generic
[    0.954591] usbcore: registered new interface driver ch341
[    0.960319] usbserial: USB Serial support registered for ch341-uart
[    0.966869] usbcore: registered new interface driver cp210x
[    0.972692] usbserial: USB Serial support registered for cp210x
[    0.978867] usbcore: registered new interface driver pl2303
[    0.984689] usbserial: USB Serial support registered for pl2303
[    1.491798] i8042: i8042 controller selftest timeout
[    1.497460] jzmmc_v1.2 jzmmc_v1.2.0: vmmc regulator missing
[    1.542527] jzmmc_v1.2 jzmmc_v1.2.0: register success!
[    1.547915] jzmmc_v1.2 jzmmc_v1.2.1: vmmc regulator missing
[    1.593450] jzmmc_v1.2 jzmmc_v1.2.1: register success!
[    1.598935] hidraw: raw HID events driver (C) Jiri Kosina
[    1.604820] usbcore: registered new interface driver usbhid
[    1.610599] usbhid: USB HID core driver
[    1.614688] Netfilter messages via NETLINK v0.30.
[    1.619620] nf_conntrack version 0.5.0 (1551 buckets, 6204 max)
[    1.626375] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.631990] TCP: cubic registered
[    1.635478] NET: Registered protocol family 17
[    1.641094] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    1.648339] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.660240] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.668044] Freeing unused kernel memory: 236K (80545000 - 80580000)
[    1.815700] dwc2 dwc2:  ++OTG Interrupt: A-Device Timeout Change++
mdev is ok......
Trying to mount SDCard...
GPIO 25   in  
GPIO 26   out  
GPIO 25   out  
GPIO 49   out  
GPIO 47   out  
GPIO 48   out  
GPIO 43   in  
right_count=3  value=0 last_value=0
[    3.702417] jzmmc_v1.2 jzmmc_v1.2.0: card inserted, state=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
[    4.782995] wait stable.[246][cgu_msc0]
[    4.787029] mmc0: new high speed SD card at address 1234
[    4.795180] mmcblk0: mmc0:1234 SA02G 1.83 GiB 
[    4.804401]  mmcblk0: p1
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
not in singleboard test
Mount sucessful
Couldnt find run.sh, starting normal...

Ingenic-uc1_1 login: [    6.684093] register all isp device successfully!
[    6.692517] @@@@ tx-isp-probe ok @@@@@
[    6.740083] exFAT: Version 1.2.9
[    6.768181] motor_probe743
[    6.805819] jz_codec_register: probe() successful!
[    7.162816] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06 desc a4eea000)
[    7.172074] dma dma0chan25: Channel 25 have been requested.(phy id 6,type 0x06 desc a4fae000)
[    7.198044] jz_pwm_probe[198] d_name = tcu_chn0
[    7.213070] request pwm channel 0 successfully
[    7.221986] pwm-jz pwm-jz: jz_pwm_probe register ok !
[    7.582303] RTL871X: module init start
[    7.588191] RTL871X: rtl8189ftv v4.3.24.7_21113.20170208.nova.1.02
[    7.594687] RTL871X: build time: Jan 24 2018 14:43:26
[    7.599927] wlan power on
[    7.622815] RTL871X: module init ret=0
GPIO 25   in  
GPIO 26   out  
GPIO 25   out  
GPIO 49   out  
GPIO 47   out  
GPIO 48   out  
GPIO 43   in  
right_count=3  value=0 last_value=0
[    7.668201] mmc1: card claims to support voltages below the defined range. These will be ignored.
[    7.688527] mmc1: new SDIO card at address 0001
[    7.696081] RTL871X: ++++++++rtw_drv_init: vendor=0x024c device=0xf179 class=0x07
[    7.744769] RTL871X: HW EFUSE
[    7.747870] RTL871X: hal_com_config_channel_plan chplan:0x20
right_count=3  value=0 last_value=0
[    7.851041] RTL871X: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
[    7.862137] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=c8:02:8f:71:37:f4
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
right_count=3  value=0 last_value=0
not in singleboard test
xxq:begin to check the sensor type
[   11.426194] name : i2c-gpio1 nr : 1
[   11.432868] name : i2c0 nr : 0
[   11.496486]  sensor_read: addr=0xa value = 0xf
[   11.501492]  sensor_read: addr=0xb value = 0x23
[   11.566341] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   11.573487] i2c i2c-0: --I2C txabrt:
[   11.577196] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   11.583808] error: sensor_read,154 ret = -5
[   11.588141]  sensor_read: addr=0x0 value = 0x0
[   11.592759] err sensor read addr = 0x0, value = 0x0
[   11.657951] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   11.665093] i2c i2c-0: --I2C txabrt:
[   11.668803] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   11.675467] error: sensor_read,154 ret = -5
[   11.679801]  sensor_read: addr=0x0 value = 0x0
[   11.684423] err sensor read addr = 0x0, value = 0x0
[   11.749614] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   11.756757] i2c i2c-0: --I2C txabrt:
[   11.760467] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   11.767076] error: sensor_read,154 ret = -5
[   11.771411]  sensor_read: addr=0x0 value = 0x0
[   11.776027] err sensor read addr = 0x0, value = 0x0
[   11.841213] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   11.848361] i2c i2c-0: --I2C txabrt:
[   11.852070] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   11.858681] error: sensor_read,154 ret = -5
[   11.863027]  sensor_read: addr=0x3107 value = 0x0
[   11.867899] err sensor read addr = 0x3107, value = 0x0
[   11.933365] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   11.940497] i2c i2c-0: --I2C txabrt:
[   11.944219] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   11.950818] error: sensor_read,154 ret = -5
[   11.955165]  sensor_read: addr=0x3107 value = 0x0
[   11.960039] err sensor read addr = 0x3107, value = 0x0
[   12.025506] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   12.032648] i2c i2c-0: --I2C txabrt:
[   12.036356] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   12.042964] error: sensor_read,154 ret = -5
[   12.047298]  sensor_read: addr=0x3107 value = 0x0
[   12.052170] err sensor read addr = 0x3107, value = 0x0
[   12.117663] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   12.124811] i2c i2c-0: --I2C txabrt:
[   12.128520] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   12.135130] error: sensor_read,154 ret = -5
[   12.139463]  sensor_read: addr=0x301c value = 0x0
[   12.144349] err sensor read addr = 0x301c, value = 0x0
[   12.209813] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   12.216959] i2c i2c-0: --I2C txabrt:
[   12.220667] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   12.227277] error: sensor_read,154 ret = -5
[   12.231613]  sensor_read: addr=0x301c value = 0x0
[   12.236499] err sensor read addr = 0x301c, value = 0x0
[   12.301956] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   12.309098] i2c i2c-0: --I2C txabrt:
[   12.312819] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   12.319415] error: sensor_read,154 ret = -5
[   12.323760]  sensor_read: addr=0x2 value = 0x0
[   12.328362] err sensor read addr = 0x2, value = 0x0
[   12.393558] i2c i2c-0: i2c_jz_irq 441, I2C transfer error, ABORT interrupt
[   12.400690] i2c i2c-0: --I2C txabrt:
[   12.404412] i2c i2c-0: --I2C TXABRT[0]=I2C_TXABRT_ABRT_7B_ADDR_NOACK
[   12.411010] error: sensor_read,154 ret = -5
[   12.415358]  sensor_read: addr=0x2 value = 0x0
[   12.419960] err sensor read addr = 0x2, value = 0x0
[   12.425029] info: failed sensor find
##### sensor not found
[   12.428859] misc sinfo_release
Not have the sensor driver!!!

fifa255 commented 5 years ago

Same message here. I had loaded dafang-hack and had RTSP streams working and also loaded the full HD bootloader as mentioned in the instructions at https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks. Things were working well but I was having stuttering images and stream especially when motion was detected. So I wanted to revert back to original firmware and I tried to remove run.sh which did nothing. I then removed the sd card and the camera just hangs after turning on with a yellow light.

I then opened the camera and soldered to the serial inputs and connected via serial interface and when I boot up I get the same message as above. When I try to load a new demo.bin I get the same message.

After the "Not have the sensor driver!!!" message if I press ENTER it brings me to a login prompt:

Ingenic-uc1_1 login:

I can login with user: root and pass: ismart12.

it then shows a linux file system.

At this point how can I load the original firmware or restore the dafang-hack firmware back? Any ideas.

jmtatsch commented 5 years ago

Can you undo the fullhd memory partitioning? After that install stock or custom firmware.

blackfyre commented 5 years ago

Got the same problem...

@jmtatsch I'm new to this ecosystem, could you point me to a description on how to undo the partitioning?

stale[bot] commented 5 years ago

This issue has been automatically marked as stale because it has not had recent activity. It will be closed if no further activity occurs. Thank you for your contributions.

tofurky commented 3 years ago

i was given a "dead" camera and after attaching uart i saw the same error preventing boot:

[   15.390204] info: failed sensor find
##### sensor not found
[   15.394052] misc sinfo_release
Not have the sensor driver!!!

i tried addressing it via software, e.g. flashing the stock demo.bin via u-boot (https://github.com/EliasKotlyar/Xiaomi-Dafang-Hacks/blob/master/hacks/unbrick.md), to no avail.

it turns out that the ribbon cable (widest one) connecting the cpu board to the sensor board had somehow become partially disconnected. not sure if this was due to rattling from the stepper motors, improper original assembly, oxidation on the contacts, or a combination of those.

however, the camera sprung back to life after disconnecting the ribbon cable from the cpu board and reseating/reconnecting it. there are two plastic tabs on either edge of the connector that lift up vertically to release the cable. a fingernail or small flathead driver gently can lift them up (note: they do not completely detach). when reseating, one may pop up after pressing the other down, but it's relatively straightforward to get it locked into place.

hope this helps someone encountering the same issue.

edit: the following were the external symptoms:

when powered on, orange led briefly went to blue then stayed at orange
no motion at all from pan/tilt motors

EliasKotlyar / Xiaomi-Dafang-Hacks