search

F1ATB / Remote-SDR

Remote control of 2 Software Design Radio. Receiver and transmitter. Based on Adalm-Pluto SDR or RTL-SDR or Hack RF SDR or SDRplay and signal processing using GNU Radio on Raspberry PI. GUI on a web browser.
https://f1atb.fr
GNU General Public License v3.0
144 stars 23 forks source link

Doesn't boot on OrangePi Zero 2 #32

Open osscombat opened 1 year ago

osscombat commented 1 year ago

Hi, Just gave it a try on a new OPiZ2 recently - it doesn't work as expected. No IP-address is being requested, no signal over mHDMI, network LEDs are blinking though.

Note: RPI4 image boots fine even on RPi3, but probably this board is too weak, the sound is jerking badly in the browser.

F1ATB commented 1 year ago

RPI3 is too weak. OPIZ2, may be an issue with the SD card. Currently Remote SDR version 5 image is running correctly on OPIZ2. I have good return I have one running just in front of me. 73 F1ATB

Le mar. 21 mars 2023 à 15:49, osscombat @.***> a écrit :

Hi, Just gave it a try on a new OPiZ2 recently - it doesn't work as expected. No IP-address is being requested, no signal over mHDMI, network LEDs are blinking though.

Note: RPI4 image boots fine even on RPi3, but probably this board is too weak, the sound is jerking badly in the browser.

— Reply to this email directly, view it on GitHub https://github.com/F1ATB/Remote-SDR/issues/32, or unsubscribe https://github.com/notifications/unsubscribe-auth/ACN7K5OD7T3JBONW5DKBQZLW5G5WLANCNFSM6AAAAAAWCRUPCY . You are receiving this because you are subscribed to this thread.Message ID: @.***>

-- André Buhart F1ATB https://f1atb.fr https://sea-seek.com

osscombat commented 1 year ago

It's not the sdcard, I have tried two different. Official 3.0.6 debian image boots fine, will try the manual install.

вт, 21 мар. 2023 г., 19:27 F1ATB @.***>:

RPI3 is too weak. OPIZ2, may be an issue with the SD card. Currently Remote SDR version 5 image is running correctly on OPIZ2. I have good return I have one running just in front of me. 73 F1ATB

Le mar. 21 mars 2023 à 15:49, osscombat @.***> a écrit :

Hi, Just gave it a try on a new OPiZ2 recently - it doesn't work as expected. No IP-address is being requested, no signal over mHDMI, network LEDs are blinking though.

Note: RPI4 image boots fine even on RPi3, but probably this board is too weak, the sound is jerking badly in the browser.

— Reply to this email directly, view it on GitHub https://github.com/F1ATB/Remote-SDR/issues/32, or unsubscribe < https://github.com/notifications/unsubscribe-auth/ACN7K5OD7T3JBONW5DKBQZLW5G5WLANCNFSM6AAAAAAWCRUPCY

. You are receiving this because you are subscribed to this thread.Message ID: @.***>

-- André Buhart F1ATB https://f1atb.fr https://sea-seek.com

— Reply to this email directly, view it on GitHub https://github.com/F1ATB/Remote-SDR/issues/32#issuecomment-1478170690, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHJ2YGOE72SNIYQCZ7U4K6LW5HJFTANCNFSM6AAAAAAWCRUPCY . You are receiving this because you authored the thread.Message ID: @.***>

dona76 commented 1 year ago

I encountered the same problem: partial boot with the armbian logo on the hdmi output then nothing but the fixed cursor. I replaced the Intenso 16GB microSD card with a Sandisk 32GB and it works. Both are marked: UHS I, V30, Class 10, 4k camera, UHS class 30MB/s... See : http://www.orangepi.org/orangepiwiki/index.php/Orange_Pi_Zero_2#Prepare_the_necessary_accessories