Open uhuck opened 11 months ago
Hello Fabian. I've now figured out why you can't set the FAN to BOOST. The reason is that the FAN only has 2 levels and not 3. There are only OFF, ECO and HIGH. I have a hard copy of my Truma app. You can see the selection there. If you have time, can you please change the code. Thank you!
Hi Fabian, Könnest du mir bitte eine Rückmeldung geben, ob du eine Anpassung des FAN-MODE (Siehe meinen issue oben) eingeplant hast? Falls du weitere Infos zur Steuerung meiner Truma Combi 6E brauchst, dann melde dich bitte. Viele Grüße
Highest fan level (boost) only works when the current temperature is at least 10 degrees below target temperature and it will automatically switch to normal mode (eco/high) when done heating. This is enforced by the cp plus panel
Hello Fabian. I am excited about your development of the INet Box with ESPHome in the Home Assistant. Thank you for that.
I have a motorhome with a Truma Combi 6E. The connection is going very well so far. I can control everything. Except that I can't set the FAN to the highest level. When I try this, the FAN mode strings back to Eco/Low or Medium mode.
I am sending you my ESPHome log below for examination:
INFO ESPHome 2023.12.5 INFO Reading configuration /config/esphome/truma-inet.yaml... INFO Updating https://github.com/Fabian-Schmidt/esphome-truma_inetbox.git@None INFO Detected timezone 'Europe/Berlin' INFO Starting log output from 192.168.1.208 using esphome API INFO Successfully connected to truma-inet @ 192.168.1.208 in 0.151s INFO Successful handshake with truma-inet @ 192.168.1.208 in 0.118s [11:55:54][I][app:102]: ESPHome version 2023.12.5 compiled on Dec 25 2023, 20:36:59
[11:55:54][C][wifi:405]: Local MAC: 0C:B8:15:F4:41:60 [11:55:54][C][wifi:410]: SSID: 'KUBERT'[redacted] [11:55:54][C][wifi:411]: IP Address: 192.168.1.208 [11:55:54][C][wifi:413]: BSSID: 00:1E:42:2B:E8:95[redacted]
[11:55:54][C][wifi:416]: Signal strength: -31 dB ▂▄▆█ [11:55:54][C][wifi:420]: Channel: 11 [11:55:54][C][wifi:421]: Subnet: 255.255.255.0 [11:55:54][C][wifi:422]: Gateway: 192.168.1.1 [11:55:54][C][wifi:423]: DNS1: 192.168.1.1 [11:55:54][C][wifi:424]: DNS2: 0.0.0.0
[11:55:54][C][logger:444]: Level: DEBUG [11:55:54][C][logger:445]: Log Baud Rate: 115200 [11:55:54][C][logger:447]: Hardware UART: UART0 [11:55:54][C][uart.arduino_esp32:137]: UART Bus 1: [11:55:54][C][uart.arduino_esp32:138]: TX Pin: GPIO17 [11:55:55][C][uart.arduino_esp32:139]: RX Pin: GPIO16 [11:55:55][C][uart.arduino_esp32:141]: RX Buffer Size: 256 [11:55:55][C][uart.arduino_esp32:143]: Baud Rate: 9600 baud [11:55:55][C][uart.arduino_esp32:144]: Data Bits: 8 [11:55:55][C][uart.arduino_esp32:145]: Parity: NONE [11:55:55][C][uart.arduino_esp32:146]: Stop bits: 2 [11:55:55][C][template.switch:068]: Template Switch 'Activate Room Heater' [11:55:55][C][template.switch:091]: Restore Mode: always OFF [11:55:55][C][template.switch:068]: Template Switch 'Activate Water Heater' [11:55:55][C][template.switch:091]: Restore Mode: always OFF [11:55:55][C][template.switch:091]: Restore Mode: always OFF [11:55:55][C][template.switch:057]: Optimistic: NO [11:55:55][C][template.switch:068]: Template Switch 'Active Timer' [11:55:55][C][template.switch:091]: Restore Mode: always OFF [11:55:55][C][truma_inetbox.LinBusListener:035]: Update Interval: 0.5s [11:55:55][C][truma_inetbox.LinBusListener:036]: LIN checksum Version: 2 [11:55:55][C][truma_inetbox.LinBusListener:037]: Observer mode: NO [11:55:55][C][truma_inetbox.cpplus_binary_sensor:019]: Truma CP Plus Binary Sensor 'CP Plus alive' [11:55:55][C][truma_inetbox.heater_binary_sensor:046]: Truma Heater Binary Sensor 'Room Heater active'
[11:55:55][C][truma_inetbox.heater_binary_sensor:046]: Truma Heater Binary Sensor 'Water Heater active'
[11:55:55][C][truma_inetbox.heater_binary_sensor:046]: Truma Heater Binary Sensor 'Heater mode Gas'
[11:55:55][C][truma_inetbox.heater_binary_sensor:046]: Truma Heater Binary Sensor 'Heater mode Mix 1'
[11:55:55][C][truma_inetbox.heater_binary_sensor:046]: Truma Heater Binary Sensor 'Heater mode Elec'
[11:55:55][C][truma_inetbox.heater_binary_sensor:046]: Truma Heater Binary Sensor 'Heater has error'
[11:55:55][C][truma_inetbox.timer_binary_sensor:029]: Truma Timer Binary Sensor 'Timer active' [11:55:55][C][truma_inetbox.timer_binary_sensor:030]: Type TIMER_ACTIVE [11:55:55][C][truma_inetbox.timer_binary_sensor:029]: Truma Timer Binary Sensor 'Timer Room Heater active' [11:55:55][C][truma_inetbox.timer_binary_sensor:030]: Type TIMER_ROOM [11:55:55][C][truma_inetbox.timer_binary_sensor:029]: Truma Timer Binary Sensor 'Timer Water Heater active' [11:55:55][C][truma_inetbox.timer_binary_sensor:030]: Type TIMER_WATER [11:55:55][C][truma_inetbox.room_climate:048]: truma_inetbox.room_climateTruma Room Climate 'Truma Room' [11:55:55][C][truma_inetbox.water_climate:019]: truma_inetbox.water_climateTruma Climate 'Truma Water' [11:55:55][C][truma_inetbox.heater_number:045]: Truma Heater Number 'Target Room Temperature'
[11:55:55][C][truma_inetbox.heater_number:045]: Unit of Measurement: '°C' [11:55:55][C][truma_inetbox.heater_number:045]: Device Class: 'temperature'
[11:55:55][C][truma_inetbox.heater_number:045]: Truma Heater Number 'Target Water Temperature'
[11:55:55][C][truma_inetbox.heater_number:045]: Unit of Measurement: '°C' [11:55:55][C][truma_inetbox.heater_number:045]: Device Class: 'temperature' [11:55:55][C][truma_inetbox.heater_number:045]: Truma Heater Number 'electric power level'
[11:55:55][C][truma_inetbox.sensor:049]: State Class: 'measurement' [11:55:55][C][truma_inetbox.sensor:049]: Unit of Measurement: '°C' [11:55:55][C][truma_inetbox.sensor:049]: Truma Sensor 'Current Water Temperature' [11:55:55][C][truma_inetbox.sensor:049]: Device Class: 'temperature'
[11:55:55][C][truma_inetbox.sensor:049]: Truma Sensor 'Target Room Temperature' [11:55:55][C][truma_inetbox.sensor:049]: Device Class: 'temperature' [11:55:55][C][truma_inetbox.sensor:049]: State Class: 'measurement' [11:55:55][C][truma_inetbox.sensor:049]: Unit of Measurement: '°C' [11:55:55][C][truma_inetbox.sensor:049]: Accuracy Decimals: 0
[11:55:55][C][truma_inetbox.sensor:049]: Truma Sensor 'Target Water Temperature' [11:55:56][C][truma_inetbox.sensor:049]: Device Class: 'temperature' [11:55:56][C][truma_inetbox.sensor:049]: State Class: 'measurement' [11:55:56][C][truma_inetbox.sensor:049]: Unit of Measurement: '°C' [11:55:56][C][truma_inetbox.sensor:049]: Unit of Measurement: '' [11:55:56][C][truma_inetbox.sensor:049]: Accuracy Decimals: 0
[11:55:56][C][truma_inetbox.sensor:049]: Truma Sensor 'electric power level' [11:55:56][C][truma_inetbox.sensor:049]: Device Class: 'power' [11:55:56][C][truma_inetbox.sensor:049]: State Class: 'measurement'
[11:55:56][C][truma_inetbox.sensor:049]: Truma Sensor 'Energy mix' [11:55:56][C][truma_inetbox.sensor:049]: State Class: 'measurement' [11:55:56][C][truma_inetbox.sensor:049]: Unit of Measurement: '' [11:55:56][C][truma_inetbox.sensor:049]: Accuracy Decimals: 0
[11:55:56][C][truma_inetbox.sensor:049]: Truma Sensor 'Operating status' [11:55:56][C][truma_inetbox.sensor:049]: State Class: 'measurement' [11:55:56][C][truma_inetbox.sensor:049]: Unit of Measurement: '' [11:55:56][C][truma_inetbox.sensor:049]: Accuracy Decimals: 0 [11:55:56][C][truma_inetbox.sensor:049]: Accuracy Decimals: 0
[11:55:56][C][truma_inetbox.heater_select:153]: Truma Heater Select 'Fan Mode'
[11:55:56][C][truma_inetbox.heater_select:155]: Options are: [11:55:56][C][web_server:168]: Web Server: [11:55:56][C][web_server:169]: Address: truma-inet.local:80
[11:55:56][C][mdns:116]: Hostname: truma-inet [11:55:56][C][ota:097]: Over-The-Air Updates: [11:55:56][C][ota:098]: Address: truma-inet.local:3232 [11:55:56][C][ota:101]: Using Password. [11:55:56][C][api:139]: API Server: [11:55:56][C][api:140]: Address: truma-inet.local:6053 [11:55:56][C][api:142]: Using noise encryption: YES [11:56:06][D][truma_inetbox.LinBusProtocol:226]: Multi package request BB.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.0A.15.00.7A.0D.01.00.01.01.00.00.01.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00 (41)
[11:56:06][D][truma_inetbox.TrumaiNetBoxAppClock:014]: StatusFrameClock 13:01:00 [11:56:06][D][truma_inetbox.LinBusProtocol:232]: Multi package response FB [11:56:28][D][truma_inetbox.LinBusProtocol:226]: Multi package request BB.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.14.33.00.40.E6.0A.01.00.00.00.00.00.00.00.01.01.18.0B.FA.0A.07.00.00.00.00.00.00.00 (41)
[11:56:28][D][truma_inetbox.LinBusProtocol:232]: Multi package response FB [11:56:28][D][climate:396]: 'Truma Room' - Sending state: [11:56:28][D][climate:399]: Mode: HEAT [11:56:28][D][climate:404]: Fan Mode: LOW [11:56:28][D][climate:419]: Current Temperature: 8.00°C [11:56:28][D][climate:425]: Target Temperature: 6.00°C [11:56:28][D][climate:396]: 'Truma Water' - Sending state: [11:56:28][D][climate:399]: Mode: OFF [11:56:28][D][climate:419]: Current Temperature: 11.00°C [11:56:28][D][climate:425]: Target Temperature: nan°C [11:56:28][D][number:012]: 'Target Room Temperature': Sending state 6.000000 [11:56:28][D][number:012]: 'Target Water Temperature': Sending state 0.000000 [11:56:28][D][number:012]: 'electric power level': Sending state 0.000000 [11:56:28][D][sensor:094]: 'Current Room Temperature': Sending state 8.00000 °C with 1 decimals of accuracy [11:56:28][D][sensor:094]: 'Current Water Temperature': Sending state 11.00000 °C with 0 decimals of accuracy [11:56:28][D][sensor:094]: 'Target Room Temperature': Sending state 6.00000 °C with 0 decimals of accuracy [11:56:28][D][sensor:094]: 'Target Water Temperature': Sending state nan °C with 0 decimals of accuracy [11:56:28][D][sensor:094]: 'Heating mode': Sending state 1.00000 with 0 decimals of accuracy [11:56:28][D][sensor:094]: 'electric power level': Sending state 0.00000 W with 0 decimals of accuracy [11:56:28][D][sensor:094]: 'Energy mix': Sending state 1.00000 with 0 decimals of accuracy [11:56:28][D][sensor:094]: 'Operating status': Sending state 7.00000 with 0 decimals of accuracy [11:56:28][D][sensor:094]: 'Heater error code': Sending state 0.00000 with 0 decimals of accuracy [11:56:28][D][select:015]: 'Fan Mode': Sending state Eco (index 1) [11:56:28][D][select:015]: 'Energy Mix': Sending state Gas (index 0) [11:56:28][W][component:214]: Component truma_inetbox took a long time for an operation (0.25 s). [11:56:28][W][component:215]: Components should block for at most 20-30ms. [11:57:06][D][truma_inetbox.LinBusProtocol:226]: Multi package request BB.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.0A.15.00.79.0D.02.00.01.01.00.00.01.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00 (41)
[11:57:06][D][truma_inetbox.TrumaiNetBoxAppClock:014]: StatusFrameClock 13:02:00 [11:57:06][D][truma_inetbox.LinBusProtocol:232]: Multi package response FB [11:57:34][D][truma_inetbox.LinBusProtocol:226]: Multi package request BB.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.14.33.00.40.E6.0A.01.00.00.00.00.00.00.00.01.01.18.0B.FA.0A.07.00.00.00.00.00.00.00 (41)
[11:57:34][D][truma_inetbox.LinBusProtocol:232]: Multi package response FB [11:57:34][D][climate:396]: 'Truma Room' - Sending state: [11:57:34][D][climate:399]: Mode: HEAT [11:57:34][D][climate:404]: Fan Mode: LOW [11:57:34][D][climate:419]: Current Temperature: 8.00°C [11:57:35][D][climate:425]: Target Temperature: 6.00°C [11:57:35][D][climate:396]: 'Truma Water' - Sending state: [11:57:35][D][climate:399]: Mode: OFF [11:57:35][D][climate:419]: Current Temperature: 11.00°C [11:57:35][D][climate:425]: Target Temperature: nan°C [11:57:35][D][number:012]: 'Target Room Temperature': Sending state 6.000000 [11:57:35][D][number:012]: 'Target Water Temperature': Sending state 0.000000 [11:57:35][D][number:012]: 'electric power level': Sending state 0.000000 [11:57:35][D][sensor:094]: 'Current Room Temperature': Sending state 8.00000 °C with 1 decimals of accuracy [11:57:35][D][sensor:094]: 'Current Water Temperature': Sending state 11.00000 °C with 0 decimals of accuracy [11:57:35][D][sensor:094]: 'Target Room Temperature': Sending state 6.00000 °C with 0 decimals of accuracy [11:57:35][D][sensor:094]: 'Target Water Temperature': Sending state nan °C with 0 decimals of accuracy [11:57:35][D][sensor:094]: 'Heating mode': Sending state 1.00000 with 0 decimals of accuracy [11:57:35][D][sensor:094]: 'electric power level': Sending state 0.00000 W with 0 decimals of accuracy [11:57:35][D][sensor:094]: 'Energy mix': Sending state 1.00000 with 0 decimals of accuracy [11:57:35][D][sensor:094]: 'Operating status': Sending state 7.00000 with 0 decimals of accuracy [11:57:35][D][sensor:094]: 'Heater error code': Sending state 0.00000 with 0 decimals of accuracy [11:57:35][D][select:015]: 'Fan Mode': Sending state Eco (index 1) [11:57:35][D][select:015]: 'Energy Mix': Sending state Gas (index 0) [11:57:35][W][component:214]: Component truma_inetbox took a long time for an operation (0.25 s). [11:57:35][W][component:215]: Components should block for at most 20-30ms. [11:57:35][D][climate:011]: 'Truma Room' - Setting [11:57:35][D][climate:024]: Fan: MEDIUM [11:57:36][D][truma_inetbox.LinBusProtocol:226]: Multi package request BA.00.1F.00.1E.00.00.22.FF.FF.FF (11) [11:57:36][D][truma_inetbox.TrumaiNetBoxApp:152]: Requested read: Sending heater update [11:57:36][D][truma_inetbox.LinBusProtocol:232]: Multi package response FA.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.0C.32.21.4E.E6.0A.0A.00.00.00.00.00.00.00.01.01 (29) [11:57:37][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:57:37][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:57:37][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:57:38][D][truma_inetbox.LinBusProtocol:226]: Multi package request BA.00.1F.00.1E.00.00.22.FF.FF.FF (11) [11:57:38][W][truma_inetbox.TrumaiNetBoxApp:179]: Requested read: CP Plus asks for an update, but I have none.
[11:57:38][D][truma_inetbox.LinBusProtocol:232]: Multi package response FA [11:57:38][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:57:38][D][climate:396]: 'Truma Room' - Sending state: [11:57:38][D][climate:399]: Mode: HEAT [11:57:38][D][climate:404]: Fan Mode: LOW [11:57:38][D][climate:419]: Current Temperature: 8.00°C [11:57:38][D][climate:425]: Target Temperature: 6.00°C [11:57:38][D][climate:396]: 'Truma Water' - Sending state: [11:57:38][D][climate:399]: Mode: OFF [11:57:38][D][climate:419]: Current Temperature: 11.00°C [11:57:38][D][climate:425]: Target Temperature: nan°C [11:57:38][D][number:012]: 'Target Room Temperature': Sending state 6.000000 [11:57:38][D][number:012]: 'Target Water Temperature': Sending state 0.000000 [11:57:38][D][number:012]: 'electric power level': Sending state 0.000000 [11:57:38][D][sensor:094]: 'Current Room Temperature': Sending state 8.00000 °C with 1 decimals of accuracy [11:57:38][D][sensor:094]: 'Current Water Temperature': Sending state 11.00000 °C with 0 decimals of accuracy [11:57:38][D][sensor:094]: 'Target Room Temperature': Sending state 6.00000 °C with 0 decimals of accuracy [11:57:38][D][sensor:094]: 'Target Water Temperature': Sending state nan °C with 0 decimals of accuracy [11:57:38][D][sensor:094]: 'Heating mode': Sending state 1.00000 with 0 decimals of accuracy [11:57:38][D][sensor:094]: 'electric power level': Sending state 0.00000 W with 0 decimals of accuracy [11:57:38][D][sensor:094]: 'Energy mix': Sending state 1.00000 with 0 decimals of accuracy [11:57:38][D][sensor:094]: 'Operating status': Sending state 7.00000 with 0 decimals of accuracy [11:57:38][D][sensor:094]: 'Heater error code': Sending state 0.00000 with 0 decimals of accuracy [11:57:38][D][select:015]: 'Fan Mode': Sending state Eco (index 1) [11:57:38][D][select:015]: 'Energy Mix': Sending state Gas (index 0) [11:57:38][W][component:214]: Component truma_inetbox took a long time for an operation (0.25 s). [11:57:38][W][component:215]: Components should block for at most 20-30ms. [11:58:05][D][truma_inetbox.LinBusProtocol:226]: Multi package request BB.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.0A.15.00.78.0D.03.00.01.01.00.00.01.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00 (41)
[11:58:05][D][truma_inetbox.TrumaiNetBoxAppClock:014]: StatusFrameClock 13:03:00 [11:58:06][D][truma_inetbox.LinBusProtocol:232]: Multi package response FB [11:58:06][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:58:10][D][climate:011]: 'Truma Room' - Setting [11:58:10][D][climate:024]: Fan: MEDIUM [11:58:11][D][truma_inetbox.LinBusProtocol:226]: Multi package request BA.00.1F.00.1E.00.00.22.FF.FF.FF (11) [11:58:11][D][truma_inetbox.TrumaiNetBoxApp:152]: Requested read: Sending heater update [11:58:11][D][truma_inetbox.LinBusProtocol:232]: Multi package response FA.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.0C.32.22.4D.E6.0A.0A.00.00.00.00.00.00.00.01.01 (29) [11:58:13][D][truma_inetbox.LinBusProtocol:226]: Multi package request BB.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.02.0D.22.79.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00 (41)
[11:58:13][D][truma_inetbox.TrumaiNetBoxApp:294]: StatusFrameResponseAck 22 OKAY 00 [11:58:13][D][truma_inetbox.LinBusProtocol:232]: Multi package response FB [11:58:13][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:58:15][D][truma_inetbox.LinBusProtocol:226]: Multi package request BB.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.14.33.00.37.E6.0A.0A.00.00.00.00.00.00.00.01.01.18.0B.FA.0A.07.00.00.00.00.00.00.00 (41)
[11:58:15][D][truma_inetbox.LinBusProtocol:232]: Multi package response FB [11:58:15][D][climate:396]: 'Truma Room' - Sending state: [11:58:15][D][climate:399]: Mode: HEAT [11:58:15][D][climate:404]: Fan Mode: MEDIUM [11:58:15][D][climate:419]: Current Temperature: 8.00°C [11:58:15][D][climate:425]: Target Temperature: 6.00°C [11:58:15][D][climate:396]: 'Truma Water' - Sending state: [11:58:15][D][climate:399]: Mode: OFF [11:58:15][D][climate:419]: Current Temperature: 11.00°C [11:58:15][D][climate:425]: Target Temperature: nan°C [11:58:15][D][number:012]: 'Target Room Temperature': Sending state 6.000000 [11:58:15][D][number:012]: 'Target Water Temperature': Sending state 0.000000 [11:58:15][D][number:012]: 'electric power level': Sending state 0.000000 [11:58:15][D][sensor:094]: 'Current Room Temperature': Sending state 8.00000 °C with 1 decimals of accuracy [11:58:15][D][sensor:094]: 'Current Water Temperature': Sending state 11.00000 °C with 0 decimals of accuracy [11:58:15][D][sensor:094]: 'Target Room Temperature': Sending state 6.00000 °C with 0 decimals of accuracy [11:58:15][D][sensor:094]: 'Target Water Temperature': Sending state nan °C with 0 decimals of accuracy [11:58:15][D][sensor:094]: 'Heating mode': Sending state 10.00000 with 0 decimals of accuracy [11:58:15][D][sensor:094]: 'electric power level': Sending state 0.00000 W with 0 decimals of accuracy [11:58:15][D][sensor:094]: 'Energy mix': Sending state 1.00000 with 0 decimals of accuracy [11:58:15][D][sensor:094]: 'Operating status': Sending state 7.00000 with 0 decimals of accuracy [11:58:15][D][sensor:094]: 'Heater error code': Sending state 0.00000 with 0 decimals of accuracy [11:58:15][D][select:015]: 'Fan Mode': Sending state High (index 2) [11:58:15][D][select:015]: 'Energy Mix': Sending state Gas (index 0) [11:58:15][W][component:214]: Component truma_inetbox took a long time for an operation (0.26 s). [11:58:15][W][component:215]: Components should block for at most 20-30ms. [11:58:30][D][climate:011]: 'Truma Room' - Setting [11:58:30][D][climate:024]: Fan: HIGH [11:58:31][D][truma_inetbox.LinBusProtocol:226]: Multi package request BA.00.1F.00.1E.00.00.22.FF.FF.FF (11) [11:58:31][D][truma_inetbox.TrumaiNetBoxApp:152]: Requested read: Sending heater update [11:58:31][D][truma_inetbox.LinBusProtocol:232]: Multi package response FA.00.1F.00.1E.00.00.22.FF.FF.FF.54.01.0C.32.23.4B.E6.0A.0B.00.00.00.00.00.00.00.01.01 (29) [11:58:31][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:58:31][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:58:32][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:58:32][D][truma_inetbox.LinBusProtocol:226]: Multi package request BA.00.1F.00.1E.00.00.22.FF.FF.FF (11) [11:58:32][W][truma_inetbox.TrumaiNetBoxApp:179]: Requested read: CP Plus asks for an update, but I have none.
[11:58:32][D][truma_inetbox.LinBusProtocol:232]: Multi package response FA [11:58:32][E][truma_inetbox.LinBusListener:356]: PID 3D order - unable to send response [11:58:32][D][climate:396]: 'Truma Room' - Sending state: [11:58:32][D][climate:399]: Mode: HEAT [11:58:32][D][climate:404]: Fan Mode: MEDIUM [11:58:32][D][climate:419]: Current Temperature: 8.00°C [11:58:33][D][climate:425]: Target Temperature: 6.00°C [11:58:33][D][climate:396]: 'Truma Water' - Sending state: [11:58:33][D][climate:399]: Mode: OFF [11:58:33][D][climate:419]: Current Temperature: 11.00°C [11:58:33][D][climate:425]: Target Temperature: nan°C [11:58:33][D][number:012]: 'Target Room Temperature': Sending state 6.000000 [11:58:33][D][number:012]: 'Target Water Temperature': Sending state 0.000000 [11:58:33][D][number:012]: 'electric power level': Sending state 0.000000 [11:58:33][D][sensor:094]: 'Current Room Temperature': Sending state 8.00000 °C with 1 decimals of accuracy [11:58:33][D][sensor:094]: 'Current Water Temperature': Sending state 11.00000 °C with 0 decimals of accuracy [11:58:33][D][sensor:094]: 'Target Room Temperature': Sending state 6.00000 °C with 0 decimals of accuracy [11:58:33][D][sensor:094]: 'Target Water Temperature': Sending state nan °C with 0 decimals of accuracy [11:58:33][D][sensor:094]: 'Heating mode': Sending state 10.00000 with 0 decimals of accuracy [11:58:33][D][sensor:094]: 'electric power level': Sending state 0.00000 W with 0 decimals of accuracy [11:58:33][D][sensor:094]: 'Energy mix': Sending state 1.00000 with 0 decimals of accuracy [11:58:33][D][sensor:094]: 'Operating status': Sending state 7.00000 with 0 decimals of accuracy [11:58:33][D][sensor:094]: 'Heater error code': Sending state 0.00000 with 0 decimals of accuracy [11:58:33][D][select:015]: 'Fan Mode': Sending state High (index 2) [11:58:33][D][select:015]: 'Energy Mix': Sending state Gas (index 0) [11:58:33][W][component:214]: Component truma_inetbox took a long time for an operation (0.24 s). [11:58:33][W][component:215]: Components should block for at most 20-30ms.