Open iBobik opened 2 months ago
Tried this config:
substitutions:
id_name: cooling
human_name: Cooling
<<: !include network_base.yml
esphome:
name: $id_name
friendly_name: $human_name
platformio_options:
board_build.flash_mode: dio
esp32:
board: esp32-s3-devkitc-1
variant: esp32s3
framework:
type: esp-idf
external_components:
- source: github://Fabian-Schmidt/esphome-truma_inetbox
components: ["truma_inetbox"]
uart:
- id: lin_uart_bus
baud_rate: 9600
stop_bits: 2
rx_pin: GPIO6
tx_pin: GPIO5
truma_inetbox:
uart_id: lin_uart_bus
binary_sensor:
- platform: truma_inetbox
name: "CP Plus alive"
type: CP_PLUS_CONNECTED
- platform: truma_inetbox
name: "Timer active"
type: TIMER_ACTIVE
- platform: truma_inetbox
name: "Timer room"
type: TIMER_ROOM
sensor:
- platform: truma_inetbox
name: "Current Room Temperature"
type: CURRENT_ROOM_TEMPERATURE
- platform: truma_inetbox
name: "Target Room Temperature"
type: TARGET_ROOM_TEMPERATURE
- platform: truma_inetbox
name: "Operating Status"
type: OPERATING_STATUS
climate:
- platform: truma_inetbox
name: "Truma Room"
type: ROOM
number:
- platform: truma_inetbox
name: "Target Room Temperature"
type: TARGET_ROOM_TEMPERATURE
- platform: truma_inetbox
name: "Electric Power Level"
type: ELECTRIC_POWER_LEVEL
- platform: truma_inetbox
name: "Aircon Manual Temperature"
type: AIRCON_MANUAL_TEMPERATURE
select:
- platform: truma_inetbox
name: "Fan Mode"
type: HEATER_FAN_MODE_COMBI
Then started the controller and after a minute turned on power for Aventa and using remote started air conditioning. Added device to the Home Assistant and tried to change values, but none worked:
[16:31:07][D][number:054]: 'Aircon Manual Temperature' - Setting number value
[16:31:07][D][number:113]: New number value: 31.000000
[16:31:07][W][truma_inetbox.TrumaiNetBoxAppAirconManual:055]: Cannot update Truma.
[16:32:31][D][climate:011]: 'Truma Room' - Setting
[16:32:31][D][climate:024]: Fan: OFF
[16:32:31][W][truma_inetbox.TrumaiNetBoxAppHeater:059]: Cannot update Truma.
[16:32:43][D][climate:011]: 'Truma Room' - Setting
[16:32:43][D][climate:015]: Mode: HEAT
[16:33:00][D][climate:011]: 'Truma Room' - Setting
[16:33:00][D][climate:024]: Fan: LOW
[16:33:00][W][truma_inetbox.TrumaiNetBoxAppHeater:059]: Cannot update Truma.
[16:33:25][D][number:054]: 'Target Room Temperature' - Setting number value
[16:33:25][D][number:113]: New number value: 30.000000
[16:33:25][W][truma_inetbox.TrumaiNetBoxAppHeater:059]: Cannot update Truma.
[16:33:37][D][select:062]: 'Fan Mode' - Setting
[16:33:37][D][select:115]: 'Fan Mode' - Set selected option to: Eco
[16:33:37][W][truma_inetbox.TrumaiNetBoxAppHeater:059]: Cannot update Truma.
[16:33:45][D][number:054]: 'Electric Power Level' - Setting number value
[16:33:45][D][number:113]: New number value: 0.000000
[16:33:45][W][truma_inetbox.TrumaiNetBoxAppHeater:141]: Cannot update Truma.
Hi, I just bought Aventa and would like to integrate it.
Can I help you with remote debugging and sponsor your work? (Feel free to contact me privately.)