iPhone 1.0.2 Modem Firmware 04.01.13_G

[GoogleCodeExporter]

I installed 1.1.1 with success and worked fine...Though my fault i should 
downgrade to 1.0.2  
(already did with success)  the problem now is that my iPhone version is 1.0.2 
with Modem 
Firmware 04.01.13_G. When i tried installing again 1.1.1  (pre 1.1.1 uprgade 
worked and i install 
1.1.1 through iTunes) when tried jailbreaking (activate) i could not...  Do i 
have to do something 
else in order to re-upgrade???   Maybe i can not jailbreak and have Modem 
Firmware 04.01.13_G ???

Original issue reported on code.google.com by m.olymp...@gmail.com on 16 Oct 2007 at 11:56

[GoogleCodeExporter]

I have exactly the same problem, I downgrade to 1.0.2 activate, pre-11 and 
upgrade 
to 1.1.1 but I have a "jailbreak failure" after I finish all the process of 
activate 
the 1.1.1.

Regards.

Original comment by tuta...@gmail.com on 17 Oct 2007 at 8:51

[GoogleCodeExporter]

problem seems to be the same of issue 108...

Original comment by franceg...@gmail.com on 17 Oct 2007 at 9:10

[GoogleCodeExporter]

Yep same issue here, unable to perform jailbreak after following the 
instructions in independence, always get an 
error saying jailbreak failed - this is on downgraded version to 1.02 using the 
04.01.13_G modem firmware - is 
it possible to perform the jailbreak with this combination, any help 
appreciated!

Original comment by gav...@gmail.com on 18 Oct 2007 at 9:00

[GoogleCodeExporter]

just saw these two (100 and 108) after i made my post

<a href="http://code.google.com/p/independence/issues/detail?id=137">Issue 
137</a>

Original comment by Justin.S...@gmail.com on 19 Oct 2007 at 11:41

[GoogleCodeExporter]

i have installed finally 1.1.1.....   i first pre-upgrade, then update to 1.1.1 
through itunes.....then i restart the 
computer and the phone and afterwards jailbreak....   Successssss    1.1.1

Original comment by m.olymp...@gmail.com on 19 Oct 2007 at 3:51

[GoogleCodeExporter]

Same thing worked for me.. thx!

Original comment by nasat...@gmail.com on 19 Oct 2007 at 4:52

[GoogleCodeExporter]

Yes, as I said, please read the instructions.  You need to do the Pre-1.1.1 
Upgrade before you actually upgrade to 
1.1.1.

Original comment by dial.ope...@gmail.com on 19 Oct 2007 at 6:55

[GoogleCodeExporter]

Hi to everybody. Hopefully today i got the 1.1.1 on the iPhone. My problem is 
similar to all those that i read in 
three diffrent forums where i will also paste this comment. How did i solve the 
problem?

where i was installing the ssh the wrong way from the independence. when i was 
prompted to restart the 
phone holding the home and sleep for 3 seconds, i used to press them until the 
phone shuts down WHICH IS 
WRONG! YOU HAVE TO SLIDE THE SLIDER IN ORDER TO POWER OFF! this was the problem 
for me. hope solves 
the problem for many of you out there. in a hurry what i did previously. 

i had 1.0.2 ->dfu mode and restore with 1.0.2 (you ll get error message, its 
fine! close itunes)
open apptap and run (youll get error message its fine! close apptap)
open itunes in order the phone to be recognized. close itunes
run apptap and install installer. 
run independence (i used the latest version) and activate firstly and then 
jailbreak (i had the firmware under 
home/phonedmg (a folder that i created) and in there the 1.0.2 firmware 
contents)

then i installed via installer bsd subsystem. 
then back to independence to install ssh. BE CAREFUL TO THE RESTART METHOD! 
when it is installed i changed the password and i irestarted once again using 
the same method! 

then open terminal and type rm -f  ~/.ssh/known_hosts. 
open fugu or a similar program and try to connect. if you do so, then you are 
almost done!

then follow preupgrade and you are fine! please post if it worked also for you!

credits go to stefisun!

Original comment by jkyriazi...@gmail.com on 21 Oct 2007 at 8:41