MSI PRO Z690-A DDR4 (MS-7D25)

bwsd0 commented 1 year ago

Hello,

Thank you for implementing this module. My mainboard (MSI PRO Z690-A DDR4) was flashed with Dasharo (coreboot+UEFI) v1.1.1 which may affect values of readings reported below.

Hardware Info

Mainboard: PRO Z690-A DDR4(MS-7D25)
CPU Model: 12th Gen Intel(R) Core(TM) i5-12600K

Kernel

$ uname -rms
Linux 6.2.11 x86_64

Sensor Readings

sensors nct6687-isa-0a20 | xclip -sel c

nct6687-isa-0a20
Adapter: ISA adapter
+12V:           12.17 V  (min = +12.14 V, max = +12.17 V)
+5V:             5.06 V  (min =  +5.05 V, max =  +5.06 V)
+3.3V:           3.36 V  (min =  +0.00 V, max =  +3.36 V)
CPU Soc:       522.00 mV (min =  +0.35 V, max =  +0.71 V)
CPU Vcore:     608.00 mV (min =  +0.61 V, max =  +0.61 V)
CPU 1P8:         0.00 V  (min =  +0.00 V, max =  +0.00 V)
CPU VDDP:        0.00 V  (min =  +0.00 V, max =  +0.00 V)
DRAM:            1.09 V  (min =  +0.70 V, max =  +1.43 V)
Chipset:       920.00 mV (min =  +0.91 V, max =  +0.92 V)
CPU SA:        908.00 mV (min =  +0.91 V, max =  +0.91 V)
Voltage #2:      1.53 V  (min =  +1.52 V, max =  +1.53 V)
AVCC3:           0.00 V  (min =  +0.00 V, max =  +0.00 V)
AVSB:            3.36 V  (min =  +0.00 V, max =  +3.36 V)
VBat:            1.06 V  (min =  +0.00 V, max =  +1.06 V)
CPU Fan:       1260 RPM  (min = 1224 RPM, max = 1295 RPM)
Pump Fan:         0 RPM  (min =    0 RPM, max =    0 RPM)
System Fan #1:  898 RPM  (min =  731 RPM, max =  909 RPM)
System Fan #2:    0 RPM  (min =    0 RPM, max =    0 RPM)
System Fan #3:    0 RPM  (min =    0 RPM, max =    0 RPM)
System Fan #4:    0 RPM  (min =    0 RPM, max =    0 RPM)
System Fan #5:    0 RPM  (min =    0 RPM, max =    0 RPM)
System Fan #6:    0 RPM  (min =    0 RPM, max =    0 RPM)
CPU:             +0.0°C  (low  =  +0.0°C, high =  +0.0°C)
System:         +29.0°C  (low  = +28.0°C, high = +31.0°C)
VRM MOS:        +21.5°C  (low  = +21.0°C, high = +24.0°C)
PCH:             +0.0°C  (low  =  +0.0°C, high =  +0.0°C)
CPU Socket:     +21.5°C  (low  = +21.5°C, high = +24.0°C)
PCIe x1:         +0.0°C  (low  =  +0.0°C, high =  +0.0°C)
M2_1:            +0.0°C  (low  =  +0.0°C, high =  +0.0°C)

coretemp-isa-0000 | xclip -sel c

Adapter: ISA adapter
Package id 0:  +20.0°C  (high = +80.0°C, crit = +100.0°C)
Core 0:        +15.0°C  (high = +80.0°C, crit = +100.0°C)
Core 4:        +16.0°C  (high = +80.0°C, crit = +100.0°C)
Core 8:        +17.0°C  (high = +80.0°C, crit = +100.0°C)
Core 12:       +14.0°C  (high = +80.0°C, crit = +100.0°C)
Core 16:       +17.0°C  (high = +80.0°C, crit = +100.0°C)
Core 20:       +17.0°C  (high = +80.0°C, crit = +100.0°C)
Core 28:       +20.0°C  (high = +80.0°C, crit = +100.0°C)
Core 29:       +20.0°C  (high = +80.0°C, crit = +100.0°C)
Core 30:       +18.0°C  (high = +80.0°C, crit = +100.0°C)
Core 31:       +18.0°C  (high = +80.0°C, crit = +100.0°C)

miczyg1 commented 1 year ago

Dasharo v1.1.1 does not yet configure the NCT6687D hardware monitor, so incorrect readings are expected for now.

xaizek commented 2 months ago

@t-gh-ctrl, I'm curious to know what kind of trouble you've encountered. I've enabled issues in my fork, so you can provide details there as I'm not yet openning a PR. Those changes are WIP because:

they lack documentation and commits aren't tidy
you can't set/see SmartFan mode via pwm*_enable
new pwm*_* files are shown unconditionally (should be hidden if auto mode isn't SmartFan IV)
original configuration related to new functionality isn't restored on module unloading

Setting temperature/PWM levels of auto points should work fine provided that auto mode is set to be SmartFan IV by firmware, but they are sensitive to the order in which they are set because values are constrained by the rest of the values and you're setting them one by one. Maybe if manual mode is active, constraints shouldn't be enforced to allow settings things in any order, I went with checks on every write instead of on activation of auto mode at least for now because this way you can know which value is incorrect right away.

Fred78290 / nct6687d