search

GrumpyOldPizza / ArduinoCore-stm32l0

Arduino Core for STM32L0
125 stars 67 forks source link

Cant see USB port on a MAC on 1.8.5 #2

Closed trlafleur closed 6 years ago

trlafleur commented 6 years ago

I have been unable to get IDE 1.8.5 to see the USB port to allow programing of this device on a Mac... OSX ver 10.13.2

Apple's USB prober see's the device, but its never available in the IDE...

Any ideas???

Full Speed device @ 49 (0x14213000): .............................................   Composite device: "STM32  BOOTLOADER"
    Port Information:   0x0018
           Not Captive
           External Device
           Connected
           Enabled
    Number Of Endpoints (includes EP0):   
        Total Endpoints for Configuration 1 (current):   1
    Device Descriptor   
        Descriptor Version Number:   0x0100
        Device Class:   0   (Composite)
        Device Subclass:   0
        Device Protocol:   0
        Device MaxPacketSize:   64
        Device VendorID/ProductID:   0x0483/0xDF11   (STMicroelectronics)
        Device Version Number:   0x2200
        Number of Configurations:   1
        Manufacturer String:   1 "STMicroelectronics"
        Product String:   2 "STM32  BOOTLOADER"
        Serial Number String:   3 "04B23643006B"
    Configuration Descriptor (current config)   
        Length (and contents):   45
        Number of Interfaces:   1
        Configuration Value:   1
        Attributes:   0xC0 (self-powered)
        MaxPower:   100 ma
        Interface #0 - Application Specific/Device Firmware Update ..............................................   "@Internal Flash  /0x08000000/1536*128g"
        Interface #0 - Application Specific/Device Firmware Update (#1) ..............................................   "@Option Bytes  /0x1FF80000/01*032 e"
        Interface #0 - Application Specific/Device Firmware Update (#2) ..............................................   "@DATA Memory /0x08080000/2*3Ke"
GrumpyOldPizza commented 6 years ago

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

trlafleur commented 6 years ago

Not really sure what your asking here.... I’m stuck at a point where my Mac Arduino IDE can’t see the serial port - USB port. So not sure how to load any program. As noted OSX sees the port...

I have tried to run a program, but I donot see the correct port in list of available ports. Maybe we have a chicken and egg problem?

On Tue, Mar 20, 2018 at 5:26 AM Thomas Roell notifications@github.com wrote:

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0/issues/2#issuecomment-374579155, or mute the thread https://github.com/notifications/unsubscribe-auth/AEXCK7Zt1eTyE1GPZvYO_il9gVvB8Sz8ks5tgPVogaJpZM4SvV2s .

--

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

GrumpyOldPizza commented 6 years ago

What happens if you just try to download a sketch ? What does the IDE emit as error message ?

On Wed, Mar 21, 2018 at 6:12 AM, Tom Lafleur notifications@github.com wrote:

Not really sure what your asking here.... I’m stuck at a point where my Mac Arduino IDE can’t see the serial port - USB port. So not sure how to load any program. As noted OSX sees the port...

I have tried to run a program, but I donot see the correct port in list of available ports. Maybe we have a chicken and egg problem?

On Tue, Mar 20, 2018 at 5:26 AM Thomas Roell notifications@github.com wrote:

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374579155, or mute the thread https://github.com/notifications/unsubscribe-auth/AEXCK7Zt1eTyE1GPZvYO_ il9gVvB8Sz8ks5tgPVogaJpZM4SvV2s .

--

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0/issues/2#issuecomment-374916574, or mute the thread https://github.com/notifications/unsubscribe-auth/AG4QfIZe5NaYboZjeYCWGtUCLSjnTWZ8ks5tgkPKgaJpZM4SvV2s .

trlafleur commented 6 years ago

I can see the USB device in the IDE..

I can compile a demo program , not issue But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

as noted in prior email, OSX see the device, but its NOT available to the IDE....

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

On Wed, Mar 21, 2018 at 5:20 AM, Thomas Roell notifications@github.com wrote:

What happens if you just try to download a sketch ? What does the IDE emit as error message ?

On Wed, Mar 21, 2018 at 6:12 AM, Tom Lafleur notifications@github.com wrote:

Not really sure what your asking here.... I’m stuck at a point where my Mac Arduino IDE can’t see the serial port - USB port. So not sure how to load any program. As noted OSX sees the port...

I have tried to run a program, but I donot see the correct port in list of available ports. Maybe we have a chicken and egg problem?

On Tue, Mar 20, 2018 at 5:26 AM Thomas Roell notifications@github.com wrote:

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374579155, or mute the thread https://github.com/notifications/unsubscribe- auth/AEXCK7Zt1eTyE1GPZvYO_ il9gVvB8Sz8ks5tgPVogaJpZM4SvV2s .

--

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374916574, or mute the thread https://github.com/notifications/unsubscribe-auth/ AG4QfIZe5NaYboZjeYCWGtUCLSjnTWZ8ks5tgkPKgaJpZM4SvV2s

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0/issues/2#issuecomment-374918173, or mute the thread https://github.com/notifications/unsubscribe-auth/AEXCKxbe2yXrZome4ab2HPj6xa2oEEjGks5tgkVwgaJpZM4SvV2s .

GrumpyOldPizza commented 6 years ago

But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

That is kind of the key point ... "Tools -> port" just looks for the USBD serial device, which is actually not used to download the sketch. If present it's used to reboot the board into bootloader mode, which then pops up as "STM32 BOOTLOADER" in the USB device list.

On my system (just verified again to make sure nothing changed lately), if you simply download the sketch and no port is open, it will just start the "upload" utility.

This is why I asked "can you simply push the download button on the IDE and report any error messages from there".

On Wed, Mar 21, 2018 at 12:10 PM, Tom Lafleur notifications@github.com wrote:

I can see the USB device in the IDE..

I can compile a demo program , not issue But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

as noted in prior email, OSX see the device, but its NOT available to the IDE....

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

On Wed, Mar 21, 2018 at 5:20 AM, Thomas Roell notifications@github.com wrote:

What happens if you just try to download a sketch ? What does the IDE emit as error message ?

On Wed, Mar 21, 2018 at 6:12 AM, Tom Lafleur notifications@github.com wrote:

Not really sure what your asking here.... I’m stuck at a point where my Mac Arduino IDE can’t see the serial port - USB port. So not sure how to load any program. As noted OSX sees the port...

I have tried to run a program, but I donot see the correct port in list of available ports. Maybe we have a chicken and egg problem?

On Tue, Mar 20, 2018 at 5:26 AM Thomas Roell <notifications@github.com

wrote:

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374579155, or mute the thread https://github.com/notifications/unsubscribe- auth/AEXCK7Zt1eTyE1GPZvYO_ il9gVvB8Sz8ks5tgPVogaJpZM4SvV2s .

--

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374916574, or mute the thread https://github.com/notifications/unsubscribe-auth/ AG4QfIZe5NaYboZjeYCWGtUCLSjnTWZ8ks5tgkPKgaJpZM4SvV2s

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374918173, or mute the thread https://github.com/notifications/unsubscribe-auth/ AEXCKxbe2yXrZome4ab2HPj6xa2oEEjGks5tgkVwgaJpZM4SvV2s .

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0/issues/2#issuecomment-375043244, or mute the thread https://github.com/notifications/unsubscribe-auth/AG4QfDyjavCn8tqf9Z_WIZgNk15jqt8Bks5tgpd9gaJpZM4SvV2s .

trlafleur commented 6 years ago

Will try and see what happens. This is not the usual action one takes on most boards.

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

On Mar 21, 2018, at 11:17 AM, Thomas Roell notifications@github.com wrote:

But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

That is kind of the key point ... "Tools -> port" just looks for the USBD serial device, which is actually not used to download the sketch. If present it's used to reboot the board into bootloader mode, which then pops up as "STM32 BOOTLOADER" in the USB device list.

On my system (just verified again to make sure nothing changed lately), if you simply download the sketch and no port is open, it will just start the "upload" utility.

This is why I asked "can you simply push the download button on the IDE and report any error messages from there".

On Wed, Mar 21, 2018 at 12:10 PM, Tom Lafleur notifications@github.com wrote:

I can see the USB device in the IDE..

I can compile a demo program , not issue But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

as noted in prior email, OSX see the device, but its NOT available to the IDE....

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

On Wed, Mar 21, 2018 at 5:20 AM, Thomas Roell notifications@github.com wrote:

What happens if you just try to download a sketch ? What does the IDE emit as error message ?

On Wed, Mar 21, 2018 at 6:12 AM, Tom Lafleur notifications@github.com wrote:

Not really sure what your asking here.... I’m stuck at a point where my Mac Arduino IDE can’t see the serial port - USB port. So not sure how to load any program. As noted OSX sees the port...

I have tried to run a program, but I donot see the correct port in list of available ports. Maybe we have a chicken and egg problem?

On Tue, Mar 20, 2018 at 5:26 AM Thomas Roell <notifications@github.com

wrote:

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374579155, or mute the thread https://github.com/notifications/unsubscribe- auth/AEXCK7Zt1eTyE1GPZvYO_ il9gVvB8Sz8ks5tgPVogaJpZM4SvV2s .

--

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374916574, or mute the thread https://github.com/notifications/unsubscribe-auth/ AG4QfIZe5NaYboZjeYCWGtUCLSjnTWZ8ks5tgkPKgaJpZM4SvV2s

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374918173, or mute the thread https://github.com/notifications/unsubscribe-auth/ AEXCKxbe2yXrZome4ab2HPj6xa2oEEjGks5tgkVwgaJpZM4SvV2s .

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0/issues/2#issuecomment-375043244, or mute the thread https://github.com/notifications/unsubscribe-auth/AG4QfDyjavCn8tqf9Z_WIZgNk15jqt8Bks5tgpd9gaJpZM4SvV2s .

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub, or mute the thread.

trlafleur commented 6 years ago

Suffix successfully added to file Using library LoRaWAN at version 1.0.0 in folder: /Users/lafleur/Desktop/MySensor-Arduino-development/Arduino_fork/hardware/TleraCorp/stm32l0/libraries/LoRaWAN

Using library STM32L0 at version 1.0 in folder: /Users/lafleur/Desktop/MySensor-Arduino-development/Arduino_fork/hardware/TleraCorp/stm32l0/libraries/STM32L0

Sketch uses 72512 bytes (36%) of program storage space. Maximum is 196608 bytes. Global variables use 6192 bytes (30%) of dynamic memory, leaving 14288 bytes for local variables. Maximum is 20480 bytes. Forcing reset using 1200bps open/close on port /dev/cu.SLAB_USBtoUART6 /Users/lafleur/Desktop/MySensor-Arduino-development/Arduino_fork/hardware/TleraCorp/stm32l0/tools/macosx/stm32l0-upload 0x1209 0x6665 /var/folders/53/f8mlg0xn1xv3fsm58phqmtb40000gn/T/arduino_build_731149/LoRaWAN_OTAA_US915.ino.dfu

10 9 8 7 6 5 4 3 2 1 FAIL

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

On Wed, Mar 21, 2018 at 11:46 AM, Tom Lafleur lafleur@lafleur.us wrote:

Will try and see what happens. This is not the usual action one takes on most boards.

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

On Mar 21, 2018, at 11:17 AM, Thomas Roell notifications@github.com wrote:

But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

That is kind of the key point ... "Tools -> port" just looks for the USBD serial device, which is actually not used to download the sketch. If present it's used to reboot the board into bootloader mode, which then pops up as "STM32 BOOTLOADER" in the USB device list.

On my system (just verified again to make sure nothing changed lately), if you simply download the sketch and no port is open, it will just start the "upload" utility.

This is why I asked "can you simply push the download button on the IDE and report any error messages from there".

  • Thomas

On Wed, Mar 21, 2018 at 12:10 PM, Tom Lafleur notifications@github.com wrote:

I can see the USB device in the IDE..

I can compile a demo program , not issue But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

as noted in prior email, OSX see the device, but its NOT available to the IDE....

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

On Wed, Mar 21, 2018 at 5:20 AM, Thomas Roell notifications@github.com wrote:

What happens if you just try to download a sketch ? What does the IDE emit as error message ?

On Wed, Mar 21, 2018 at 6:12 AM, Tom Lafleur <notifications@github.com

wrote:

Not really sure what your asking here.... I’m stuck at a point where my Mac Arduino IDE can’t see the serial port - USB port. So not sure how to load any program. As noted OSX sees the port...

I have tried to run a program, but I donot see the correct port in list of available ports. Maybe we have a chicken and egg problem?

On Tue, Mar 20, 2018 at 5:26 AM Thomas Roell < notifications@github.com

wrote:

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374579155, or mute the thread https://github.com/notifications/unsubscribe- auth/AEXCK7Zt1eTyE1GPZvYO_ il9gVvB8Sz8ks5tgPVogaJpZM4SvV2s .

--

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374916574, or mute the thread https://github.com/notifications/unsubscribe-auth/ AG4QfIZe5NaYboZjeYCWGtUCLSjnTWZ8ks5tgkPKgaJpZM4SvV2s

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374918173, or mute the thread https://github.com/notifications/unsubscribe-auth/ AEXCKxbe2yXrZome4ab2HPj6xa2oEEjGks5tgkVwgaJpZM4SvV2s .

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-375043244, or mute the thread https://github.com/notifications/unsubscribe-auth/AG4QfDyjavCn8tqf9Z_ WIZgNk15jqt8Bks5tgpd9gaJpZM4SvV2s .

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0/issues/2#issuecomment-375045784, or mute the thread https://github.com/notifications/unsubscribe-auth/AEXCK5-qDsUtEb9DQHxfOK6eb3jngpihks5tgpk9gaJpZM4SvV2s .

GrumpyOldPizza commented 6 years ago

Can you hold the BOOT button while you toggle RESET on the board. Of course USB should be connectected all the time.

Then run form a command shell:

/Users/lafleur/Desktop/MySensor-Arduino-development/Arduino_fork/hardware/TleraCorp/stm32l0/tools/macosx/dfu-util -l

I do not quite understand the output that you send me. It implies that there is a USB port to toggle (which you said was not there), and then it fails to flash, while it's already in bootloader mode (as per previous e-mail). So let's see whether the flash utility throws an error, or reports something unexpected.

On Wed, Mar 21, 2018 at 2:29 PM, Tom Lafleur notifications@github.com wrote:

Suffix successfully added to file Using library LoRaWAN at version 1.0.0 in folder: /Users/lafleur/Desktop/MySensor-Arduino-development/Arduino_fork/hardware/ TleraCorp/stm32l0/libraries/LoRaWAN

Using library STM32L0 at version 1.0 in folder: /Users/lafleur/Desktop/MySensor-Arduino-development/Arduino_fork/hardware/ TleraCorp/stm32l0/libraries/STM32L0

Sketch uses 72512 bytes (36%) of program storage space. Maximum is 196608 bytes. Global variables use 6192 bytes (30%) of dynamic memory, leaving 14288 bytes for local variables. Maximum is 20480 bytes. Forcing reset using 1200bps open/close on port /dev/cu.SLAB_USBtoUART6 /Users/lafleur/Desktop/MySensor-Arduino-development/Arduino_fork/hardware/ TleraCorp/stm32l0/tools/macosx/stm32l0-upload 0x1209 0x6665 /var/folders/53/f8mlg0xn1xv3fsm58phqmtb40000gn/T/arduino_build_731149/ LoRaWAN_OTAA_US915.ino.dfu

10 9 8 7 6 5 4 3 2 1 FAIL

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

On Wed, Mar 21, 2018 at 11:46 AM, Tom Lafleur lafleur@lafleur.us wrote:

Will try and see what happens. This is not the usual action one takes on most boards.

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

On Mar 21, 2018, at 11:17 AM, Thomas Roell notifications@github.com wrote:

But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

That is kind of the key point ... "Tools -> port" just looks for the USBD serial device, which is actually not used to download the sketch. If present it's used to reboot the board into bootloader mode, which then pops up as "STM32 BOOTLOADER" in the USB device list.

On my system (just verified again to make sure nothing changed lately), if you simply download the sketch and no port is open, it will just start the "upload" utility.

This is why I asked "can you simply push the download button on the IDE and report any error messages from there".

  • Thomas

On Wed, Mar 21, 2018 at 12:10 PM, Tom Lafleur notifications@github.com wrote:

I can see the USB device in the IDE..

I can compile a demo program , not issue But when I select Tools-->port the device is NOT listed there, so one CAN'T start as download as the USDB device is NOT visible....

as noted in prior email, OSX see the device, but its NOT available to the IDE....

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

On Wed, Mar 21, 2018 at 5:20 AM, Thomas Roell < notifications@github.com> wrote:

What happens if you just try to download a sketch ? What does the IDE emit as error message ?

On Wed, Mar 21, 2018 at 6:12 AM, Tom Lafleur < notifications@github.com

wrote:

Not really sure what your asking here.... I’m stuck at a point where my Mac Arduino IDE can’t see the serial port - USB port. So not sure how to load any program. As noted OSX sees the port...

I have tried to run a program, but I donot see the correct port in list of available ports. Maybe we have a chicken and egg problem?

On Tue, Mar 20, 2018 at 5:26 AM Thomas Roell < notifications@github.com

wrote:

What happens if you simply upload the first sketch ? Like "Blink" ? At that point it should had over control to dfu-utils, which should see the "STM32 BOOTLOADER". Before you have the first sketch loaded there will be no serial port available (assuming that's what you tried to do).

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374579155, or mute the thread https://github.com/notifications/unsubscribe- auth/AEXCK7Zt1eTyE1GPZvYO_ il9gVvB8Sz8ks5tgPVogaJpZM4SvV2s .

--

~~ /) ~~~~ /) ~~ _/) ~~ _/) ~~

Tom Lafleur

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374916574, or mute the thread https://github.com/notifications/unsubscribe-auth/ AG4QfIZe5NaYboZjeYCWGtUCLSjnTWZ8ks5tgkPKgaJpZM4SvV2s

.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-374918173, or mute the thread https://github.com/notifications/unsubscribe-auth/ AEXCKxbe2yXrZome4ab2HPj6xa2oEEjGks5tgkVwgaJpZM4SvV2s .

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-375043244, or mute the thread https://github.com/notifications/unsubscribe-auth/AG4QfDyjavCn8tqf9Z_ WIZgNk15jqt8Bks5tgpd9gaJpZM4SvV2s .

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore- stm32l0/issues/2#issuecomment-375045784, or mute the thread https://github.com/notifications/unsubscribe-auth/AEXCK5- qDsUtEb9DQHxfOK6eb3jngpihks5tgpk9gaJpZM4SvV2s .

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/GrumpyOldPizza/ArduinoCore-stm32l0/issues/2#issuecomment-375085083, or mute the thread https://github.com/notifications/unsubscribe-auth/AG4QfNfV6urlYX1CO8m-g5unXwmwUiOrks5tgrhFgaJpZM4SvV2s .

GrumpyOldPizza commented 6 years ago

No feedback for 5 days. Verified that dfu-utils properly works on a Mac (thanx Simon).