Unable to receive calls

[GoogleCodeExporter]

Did you search through the other issues to make sure that this issue has
not been already reported?
Did you look at the FAQ http://wiki.openetna.com/w/Manual:FAQ ?
Did you use SetCPU or other means to overclock the cpu? The report will
only be accepted if the problem occurs _without_ overclocking!

What steps will reproduce the problem?
1. trying calling to the mobile, it says busy and getting disconnected.
2.
3.

What is the expected output? What do you see instead?
Call should come

What version of OpenEtna are you using?
6.3 RC7

Can you provide logcat output during that error?

If the issue made your phone crash&reboot, please provide the output of
"adb shell cat /proc/last_kmsg" on the boot following the crash.

Please provide any additional information below.

Original issue reported on code.google.com by yakaaith...@gmail.com on 18 Feb 2011 at 9:02

[GoogleCodeExporter]

Probably because it's busy .... or your network has problems.

Is anyone else having this issue?

Original comment by trmfrei...@gmail.com on 18 Feb 2011 at 10:25

• Changed state: NeedInfo

[GoogleCodeExporter]

No, there is very good network , i can make outgoing calls . But no incoming. 

Original comment by yakaaith...@gmail.com on 18 Feb 2011 at 10:29

[GoogleCodeExporter]

Are you trying to call your mobile from your mobile? :p

Well, try to call your mobile from a different phone. 

(on the 1st line I wask kidding. .. )

Original comment by trmfrei...@gmail.com on 18 Feb 2011 at 11:23

• Changed title: Unable to recieve calls

[GoogleCodeExporter]

In Argentina, with Movistar, I'm able to receive and send calls!
In fact, in RC7, when somebody calls you, the phone in 1 second show you the 
screen for answer, yet when the phone is in sleep mode.

Original comment by lfg.1...@gmail.com on 18 Feb 2011 at 10:11

[GoogleCodeExporter]

I am having the same problem.
I stared at the screen and the call did not come through, although the Call Log 
documented an incoming call at the exact time I was looking, and I knew someone 
was trying to call. Rogers Canada V6.3-rc7

Original comment by LynnYeb...@gmail.com on 20 Feb 2011 at 7:10

[GoogleCodeExporter]

If this is consistent please save a logcat of it happening.

Original comment by trmfrei...@gmail.com on 20 Feb 2011 at 5:47

[GoogleCodeExporter]

I reflashed v6.3-rc7 and installed gapps tiny. after reboot, I can confirm that 
I am receiving incoming calls. Yakaaith, you may want to look into the gapps 
installation.

Original comment by LynnYeb...@gmail.com on 20 Feb 2011 at 8:14

[GoogleCodeExporter]

Yakaaith please comment on this issue.

Original comment by trmfrei...@gmail.com on 21 Feb 2011 at 11:51

• Changed state: Staling

[GoogleCodeExporter]

Hi guys, 

its fine now after reflashing. i am able to receive incoming calls 

Original comment by yakaaith...@gmail.com on 21 Feb 2011 at 3:00

[GoogleCodeExporter]

Original comment by trmfrei...@gmail.com on 21 Feb 2011 at 3:39

• Changed title: Unable to receive calls
• Changed state: FAQ

[GoogleCodeExporter]

Indeed I had the same issue with this RC7. Maybe the first to detect it. I've 
immediately switched back to RC5. Meanwhile, I just fall in this post: 
http://forum.openetna.com/index.php?topic=773.msg7365#msg7365

I think, the solution is to install GAPPS in order to receive calls... A little 
bit stupid, once I really don't want to slow down my mobile with google apps.
I may confirm this with mine if necessary.

Cheers

Original comment by gad...@gmail.com on 3 Mar 2011 at 3:10

[GoogleCodeExporter]

Phone don't get slower then GAPPS installed. Can confirm this. 

Original comment by Fedo...@gmail.com on 3 Mar 2011 at 5:00

[GoogleCodeExporter]

I too couldn't receive calls until I installed Gapps tiny,  no its fine.

Original comment by billybob...@gmail.com on 13 Mar 2011 at 8:08