help! GBIS plot - Githubissues

JackDMcGrath / GBIS

COMET GBIS software, as adapted by members of Active Tectonics Group, University of Leeds

7 stars 3 forks source link

help! GBIS plot #15

Open CUMT530849827 opened 4 months ago

CUMT530849827 commented 4 months ago

Hello, author, I would like to ask about some problems I have when using GBIS. I raised this problem in the discussion group, but no one has replied to me for a long time, so I take the liberty to bother you. The problem is that this problem occurs every time I invert and draw the joint distribution map, even in the column

855a79ef363f3dd19f6df3d0e650daa

JackDMcGrath commented 4 months ago

Have you edited any of the generate report scripts?

On Sun, 26 May 2024, 18:02 CUMT530849827, @.***> wrote:

Hello, author, I would like to ask about some problems I have when using GBIS. I raised this problem in the discussion group, but no one has replied to me for a long time, so I take the liberty to bother you. The problem is that this problem occurs every time I invert and draw the joint distribution map, even in the column

855a79ef363f3dd19f6df3d0e650daa.png (view on web) https://github.com/JackDMcGrath/GBIS/assets/49933485/f2bac958-acc8-4b93-91e7-c5bfa1be6f35

— Reply to this email directly, view it on GitHub https://github.com/JackDMcGrath/GBIS/issues/15, or unsubscribe https://github.com/notifications/unsubscribe-auth/AKQ7JPCNDLBAL7PVCQZ4NXDZEF3H7AVCNFSM6AAAAABIJQJJJ6VHI2DSMVQWIX3LMV43ASLTON2WKOZSGMYTONBZHE3TKNA . You are receiving this because you are subscribed to this thread.Message ID: @.***>

CUMT530849827 commented 4 months ago

@JackDMcGrath Thank you for your reply. The software is the original file I downloaded from the official website without any editing. I tried to put the following three scripts on the forum into the corresponding parties, but they did not get the correct drawing

JackDMcGrath commented 4 months ago

Can you share the outputs of your GBIS run, copy and paste the command you ran, and I'll try to recreate the error

Jack

On Mon, May 27, 2024 at 1:05 PM CUMT530849827 @.***> wrote:

@JackDMcGrath https://github.com/JackDMcGrath Thank you for your reply. The software is the original file I downloaded from the official website without any editing. I tried to put the following three scripts on the forum into the corresponding parties, but they did not get the correct drawing image.png (view on web) https://github.com/JackDMcGrath/GBIS/assets/49933485/a2b8b3ef-8a77-46e0-a083-29c7ef3bcc75

— Reply to this email directly, view it on GitHub https://github.com/JackDMcGrath/GBIS/issues/15#issuecomment-2132474097, or unsubscribe https://github.com/notifications/unsubscribe-auth/AKQ7JPEDOIH6RTBRVIQJJBDZEKBFTAVCNFSM6AAAAABIJQJJJ6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDCMZSGQ3TIMBZG4 . You are receiving this because you were mentioned.Message ID: @.***>

CUMT530849827 commented 4 months ago

is this ？

addpath(genpath('/opt/GBIS_V1.1/GBIS')) testGBISPath

/opt/GBIS_V1.1/GBIS/GBISrun.m /opt/GBIS_V1.1/GBIS/PrepareData/loadInsarData.m /opt/GBIS_V1.1/GBIS/DeformationSources/mogi/mogi.m /opt/GBIS_V1.1/GBIS/PlotData/plotInsarWrapped.m /opt/GBIS_V1.1/GBIS/PrepareReport/generateFinalReport.m /opt/GBIS_V1.1/GBIS/RunInversion/runInversion.m /opt/GBIS_V1.1/GBIS/ThirdPartyScripts/local2llh.m /opt/GBIS_V1.1/GBIS/Variogram/fitVariogram.m

If you see this message, you are ready to go!

generateFinalReport('invert_1_2_GPS_M_D.mat',1)

CUMT530849827 commented 4 months ago