Closed Printo1987 closed 1 year ago
Can you see your printer/mainboard with using 'lsusb' or 'dmesg'?
Have you already tried a different USB cable?
before I using rpi3 and normal working but I change this sonic for Delta becuase I wanna using accelometr with Sonic and NO MCU;/ I change 3cable usb and no mcu maybe klipper dorectory is another folder? no kiauh?
At least there is no known general problem. Without further details it is hard to help.
So please provide more information, like what have you tried and ie. the output of already mentioned commands.
I see this too:###### Identifying MCU connected via USB in DFU mode ...
/home/sonic/kiauh/scripts/flash_klipper.sh: line 340: lsusb: command not found
No MCU found! MCU either not connected or not detected!
Please provide requested information, otherwise I can't help.
I install everything if I go kiauh GET MCU i see NO MCU;/
if I plugin my previously RPI3 i see: serial: /dev/serial/by-id/usb-Klipper_sam3x8e_203120514D3652323133303035303234-if00 but on this sonic debian I no see nothing;/
I've Arduino Due and on this I've compilation flash by USB
I need the requested information to help you and you are not providing them. Sorry, I'm out here then.
I need the requested information to help you and you are not providing them. Sorry, I'm out here then.
I must chec this right? Can you see your printer/mainboard with using 'lsusb' or 'dmesg'?
after copy and paste what i see on the screen?
If i use by putty comend: sonic@SonicPad:~$ lsusb -bash: lsusb: command not found
if I use dmesg i see:
sonic@SonicPad:~$ dmesg [ 2.515530] hub 1-1:1.0: USB hub found [ 2.516118] hub 1-1:1.0: 4 ports detected [ 2.545151] IR RC5(x/sz) protocol handler initialized [ 2.550842] IR RC6 protocol handler initialized [ 2.555949] IR JVC protocol handler initialized [ 2.561052] IR Sony protocol handler initialized [ 2.566255] IR SANYO protocol handler initialized [ 2.571554] IR Sharp protocol handler initialized [ 2.576853] IR MCE Keyboard/mouse protocol handler initialized [ 2.583421] IR XMP protocol handler initialized [ 2.589601] usbcore: registered new interface driver uvcvideo [ 2.596079] USB Video Class driver (1.1.1) [ 2.600698] sunxi cedar version 0.1 [ 2.604896] VE: install start!!!
[ 2.610434] cedar_ve: cedar-ve the get irq is 344 [ 2.616068] VE: line 1811 set the sram data
[ 2.623403] VE: get debugfs_mpp_root is NULL, please check mpp
[ 2.631640] VE: sunxi ve debug register driver failed!
[ 2.639094] VE: install end!!!
[ 2.646299] Bluetooth: HCI UART driver ver 2.2.74e8f89.20201026-111523
[ 2.653665] Bluetooth: HCI UART protocol (null) registered
[ 2.659851] Bluetooth: HCI H4 protocol initialized
[ 2.665249] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 01.00.07
[ 2.672975] bt_fdi debugfs_init
[ 2.686921] sunxi-mmc sdc2: SD/MMC/SDIO Host Controller Driver(v3.48 2020-9-1 5 16:01)
[ 2.695961] sunxi-mmc sdc2: ctl-spec-caps 8
[ 2.701917] sunxi-mmc sdc2: No vdmmc regulator found
[ 2.707516] sunxi-mmc sdc2: No vd33sw regulator found
[ 2.713208] sunxi-mmc sdc2: No vd18sw regulator found
[ 2.718903] sunxi-mmc sdc2: No vq33sw regulator found
[ 2.724591] sunxi-mmc sdc2: No vq18sw regulator found
[ 2.731220] sunxi-mmc sdc2: set host busy
[ 2.735834] mmc:failed to get gpios
[ 2.740525] sunxi-mmc sdc2: sdc set ios:clk 0Hz bm PP pm UP vdd 22 width 1 ti ming LEGACY(SDR12) dt B
[ 2.769800] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.797809] sunxi-mmc sdc2: detmode:alway in(non removable)
[ 2.797830] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.806214] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.807302] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.818165] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.818248] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.831107] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.876278] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[ 2.887299] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.48 2020-9-1 5 16:01)
[ 2.887440] sunxi-mmc sdc1: ctl-spec-caps 8
[ 2.887581] sunxi-mmc sdc1: No vmmc regulator found
[ 2.887585] sunxi-mmc sdc1: No vqmmc regulator found
[ 2.887590] sunxi-mmc sdc1: No vdmmc regulator found
[ 2.887594] sunxi-mmc sdc1: No vd33sw regulator found
[ 2.887599] sunxi-mmc sdc1: No vd18sw regulator found
[ 2.887604] sunxi-mmc sdc1: No vq33sw regulator found
[ 2.887608] sunxi-mmc sdc1: No vq18sw regulator found
[ 2.888505] sunxi-mmc sdc1: set host busy
[ 2.888612] mmc:failed to get gpios
[ 2.889393] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 ti ming LEGACY(SDR12) dt B
[ 2.889417] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[ 2.905801] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.925807] sunxi-mmc sdc1: detmode:manually by software
[ 2.926643] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 2.927472] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 2.927499] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.929985] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.931892] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.932690] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.932721] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.933318] usbcore: registered new interface driver usbhid
[ 2.933321] usbhid: USB HID core driver
[ 2.933545] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.934369] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.934393] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 ti ming LEGACY(SDR12) dt B
[ 2.935486] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 ti ming LEGACY(SDR12) dt B
[ 2.935570] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[ 2.939452] sun50iw10p1-pinctrl pio: expect_func as:pcm0, but muxsel(3) is fu nc:h_i2s0
[ 2.939460] sun50iw10p1-pinctrl pio: expect_func as:pcm0, but muxsel(3) is fu nc:h_i2s0
[ 2.939467] sun50iw10p1-pinctrl pio: expect_func as:pcm0, but muxsel(3) is fu nc:h_i2s0
[ 2.939474] sun50iw10p1-pinctrl pio: expect_func as:pcm0, but muxsel(3) is fu nc:h_i2s0
[ 2.939481] sun50iw10p1-pinctrl pio: expect_func as:pcm0, but muxsel(3) is fu nc:h_i2s0
[ 2.939874] sun50iw10p1-pinctrl pio: pin PB4 already requested by \x14; ca nnot claim for daudio0
[ 2.939881] sun50iw10p1-pinctrl pio: pin-36 (daudio0) status -22
[ 2.939888] sun50iw10p1-pinctrl pio: could not request pin 36 (PB4) from grou p PB4 on device pio
[ 2.939893] sunxi-daudio daudio0: Error applying setting, reverse things back
[ 2.940081] sunxi-daudio: probe of daudio0 failed with error -22
[ 2.943382] sunxi-internal-codec codec: [sunxi_internal_codec_probe] codec pr obe finished.
[ 2.945231] [sunxi_card_init] card init finished.
[ 2.947666] sunxi-codec-machine sndcodec: sun50iw10codec <-> 5096000.cpudai-c ontroller mapping ok
[ 2.951972] sunxi-codec-machine sndcodec: [sunxi_card_dev_probe] register car d finished.
[ 2.952602] u32 classifier
[ 2.952605] Actions configured
[ 2.952820] Initializing XFRM netlink socket
[ 2.953817] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.958990] NET: Registered protocol family 10
[ 2.965481] NET: Registered protocol family 17
[ 2.965575] NET: Registered protocol family 15
[ 2.966609] 8021q: 802.1Q VLAN Support v1.8
[ 2.978906] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 2.980005] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 2.980035] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.982680] sunxi-mmc sdc1: sdc set ios:clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.984865] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.985961] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.987054] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.988141] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 2.988165] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 ti ming LEGACY(SDR12) dt B
[ 2.989263] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 ti ming LEGACY(SDR12) dt B
[ 2.989355] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[ 3.009824] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.015136] sid_rd_ver_reg()471 - ver >= 4, soc ver:4
[ 3.020750] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not su pported by regulator
[ 3.020760] cpu cpu0: _opp_add: OPP not supported by regulators (1464000000)
[ 3.021201] cpu cpu1: opp_list_debug_create_link: Failed to create link
[ 3.021208] cpu cpu1: _add_opp_dev: Failed to register opp debugfs (-12)
[ 3.021268] cpu cpu2: opp_list_debug_create_link: Failed to create link
[ 3.021274] cpu cpu2: _add_opp_dev: Failed to register opp debugfs (-12)
[ 3.021332] cpu cpu3: opp_list_debug_create_link: Failed to create link
[ 3.021337] cpu cpu3: _add_opp_dev: Failed to register opp debugfs (-12)
[ 3.024197] CTPGTP driver init
[ 3.024299] sunxi_ctp_startup: ctp_power_io is invalid.
[ 3.024351] deviceless supply not found, using dummy regulator
[ 3.024439] get ctp_screen_max_x is fail, -22
[ 3.031399] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 3.033019] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 3.033034] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.035888] sunxi-mmc sdc1: sdc set ios:clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.038591] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.040210] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.041824] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.043440] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.043453] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 ti ming LEGACY(SDR12) dt B
[ 3.044530] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 ti ming LEGACY(SDR12) dt B
[ 3.044618] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[ 3.045839] CTPinfo.ctp_used:1
[ 3.045841] CTPinfo.twi_id:1
[ 3.045843] CTPinfo.screen_max_x:1024
[ 3.045845] CTPinfo.screen_max_y:600
[ 3.045847] CTPinfo.revert_x_flag:0
[ 3.045848] CTPinfo.revert_y_flag:0
[ 3.045850] CTPinfo.exchange_x_y_flag:0
[ 3.045852] CTPinfo.irq_gpio_number:166
[ 3.045854] CTPinfo.wakeup_gpio_number:161
[ 3.045858] *CTP**CTP* ctp_wakeup:status:0,ms = 0
[ 3.069780] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.088990] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 3.092249] sunxi-mmc sdc1: smc 1 p1 err, cmd 52, RTO !!
[ 3.092302] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.095951] sunxi-mmc sdc1: sdc set ios:clk 100000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.100338] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.103638] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.105777] *CTP**CTP* ctp_wakeup:status:1,ms = 0
[ 3.106938] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.110238] sunxi-mmc sdc1: smc 1 p1 err, cmd 5, RTO !!
[ 3.110293] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 ti ming LEGACY(SDR12) dt B
[ 3.198302] sunxi_i2c_drv_core_process()972 - [i2c6] Timeout when sending 9th SCL clk
[ 3.198320] i2c_sunxi_drv_complete()1146 - [i2c6] incomplete xfer(status: 0x1 , dev addr: 0x14)
[ 3.198327] 0x07081600: 01011001 00000001 00002800 0001ffff
[ 3.198332] 0x07081610: 00008040 00010004 00010010 00000000
[ 3.198443] sunxi_i2c_drv_core_process()972 - [i2c6] Timeout when sending 9th SCL clk
[ 3.198494] i2c_sunxi_drv_complete()1146 - [i2c6] incomplete xfer(status: 0x1 , dev addr: 0x5d)
[ 3.198500] 0x07081600: 11011001 00000001 0000bb00 00000001
[ 3.198505] 0x07081610: 00008040 00010004 00010010 00000000
[ 3.198841] sunxi_i2c_do_xfer()1926 - [i2c1] incomplete xfer (status: 0x20, d ev addr: 0x14)
[ 3.199223] the adapter number is 1
[ 3.199226] ctp_detect: addr = 5d
[ 3.199686] detect ret 2
[ 3.199688] ======detect ok !=====
[ 3.200577] CTPGTP Driver Version: V2.2<2014/01/14>CTPGTP I2C Add ress: 0x5d
[ 3.200577] random: fast init done
[ 3.201285] <<-GTP-INFO->> IC Version: 911_1060
[ 3.201292] CTPConfig Groups Lengths: 186, 186, 186, 186, 186, 186, 186 , 186
[ 3.202964] CTPSensor_ID: 0
[ 3.202967] CTPCTP_CONFIG_GROUP1 used, config length: 186
[ 3.203726] CTPCFG_GROUP1 Config Version: 66, 0x42; IC Config Version: 83, 0x53
[ 3.203730] <<-GTP-INFO->> Driver send config.
[ 3.215718] <<-GTP-INFO->> X_MAX: 1024, Y_MAX: 600, TRIGGER: 0x01
[ 3.233809] <<-GTP-INFO->> create proc entry gt9xx_config success
[ 3.234583] input: gt9xxnew_ts as /devices/virtual/input/input2
[ 3.235291] <<-GTP-INFO->> GTP works in interrupt mode.
[ 3.235305] <<-GTP-INFO->> Applied memory size:2562.
[ 3.235309] <<-GTP-INFO->> I2C function: without pre and end cmd!
[ 3.235334] <<-GTP-INFO->> Create proc entry success!
[ 3.237627] sunxi_i2c_do_xfer()1926 - [i2c2] incomplete xfer (status: 0x20, d ev addr: 0x14)
[ 3.239725] sunxi_i2c_do_xfer()1926 - [i2c2] incomplete xfer (status: 0x48, d ev addr: 0x5d)
[ 3.239938] sunxi_i2c_do_xfer()1926 - [i2c3] incomplete xfer (status: 0x20, d ev addr: 0x14)
[ 3.240113] sunxi_i2c_do_xfer()1926 - [i2c3] incomplete xfer (status: 0x48, d ev addr: 0x5d)
[ 3.240753] sunxi-rtc rtc: setting system clock to 2020-01-01 00:00:04 UTC (1 577836804)
[ 3.242152] usb0-vbus: disabling
[ 3.242176] ALSA device list:
[ 3.242179] #0: audiocodec
[ 3.882132] Waiting for root device /dev/mmcblk0p5...
[ 3.898308] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 8 timing LEGACY(SDR12) dt B
[ 3.912193] sunxi-mmc sdc2: sdc set ios:clk 400000Hz bm PP pm ON vdd 22 width 8 timing MMC-HS200 dt B
[ 3.923079] sunxi-mmc sdc2: sdc set ios:clk 100000000Hz bm PP pm ON vdd 22 wi dth 8 timing MMC-HS200 dt B
[ 3.934559] sunxi-mmc sdc2: sdc set ios:clk 100000000Hz bm PP pm ON vdd 22 wi dth 8 timing MMC-HS(SDR20) dt B
[ 3.945724] sunxi-mmc sdc2: sdc set ios:clk 52000000Hz bm PP pm ON vdd 22 wid th 8 timing MMC-HS(SDR20) dt B
[ 3.958195] sunxi-mmc sdc2: sdc set ios:clk 50000000Hz bm PP pm ON vdd 22 wid th 8 timing MMC-HS400 dt B
[ 3.968855] sunxi_mmc_get_hs400_cmd_dly,222
[ 3.973552] sunxi-mmc sdc2: failed to get HS400_cmd used default
[ 3.980328] sunxi-mmc sdc2: sdc set ios:clk 100000000Hz bm PP pm ON vdd 22 wi dth 8 timing MMC-HS400 dt B
[ 3.991063] sunxi_mmc_get_hs400_cmd_dly,222
[ 3.995759] sunxi-mmc sdc2: failed to get HS400_cmd used default
[ 4.005114] mmc0: new HS400 MMC card at address 0001
[ 4.012527] mmcblk0: mmc0:0001 DG4008 7.28 GiB
[ 4.018177] mmcblk0boot0: mmc0:0001 DG4008 partition 1 4.00 MiB
[ 4.025333] mmcblk0boot1: mmc0:0001 DG4008 partition 2 4.00 MiB
[ 4.032445] mmcblk0rpmb: mmc0:0001 DG4008 partition 3 4.00 MiB
[ 4.042469] mmcblk0: p1 p2 p3 p4 p5 p6
[ 4.057634] pstore_blk: failed to open '/dev/mmcblk0p11'!
[ 4.063751] pstore_blk: failed to open '/dev/mmcblk0p11'!
[ 4.103474] EXT4-fs (mmcblk0p5): couldn't mount as ext3 due to feature incomp atibilities
[ 4.118022] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. O pts: (null)
[ 4.127167] VFS: Mounted root (ext4 filesystem) readonly on device 179:5.
[ 4.137267] devtmpfs: mounted
[ 4.140932] Freeing unused kernel memory: 448K
[ 4.261331] systemd[1]: System time before build time, advancing clock.
[ 4.275691] systemd[1]: Failed to find module 'autofs4'
[ 4.286931] cgroup: cgroup2: unknown option "nsdelegate,memory_recursiveprot"
[ 4.295572] cgroup: cgroup2: unknown option "nsdelegate"
[ 4.314616] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +G NUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 defa ult-hierarchy=unified)
[ 4.341497] systemd[1]: Detected architecture arm64.
[ 4.366752] systemd[1]: Set hostname to
[ 6.398722] [XRADIO] Firmware completed. [ 6.404944] [WSM] Firmware Label:XR_C01.08.52.11 Jan 24 2017 10:15:58 [ 6.413512] [XRADIO] Firmware Startup Done. [ 6.465854] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 6.764172] proc: unrecognized mount option "hidepid=invisible" or missing va lue [ 7.663882] proc: unrecognized mount option "hidepid=invisible" or missing va lue [ 8.259624] proc: unrecognized mount option "hidepid=invisible" or missing va lue [ 8.491125] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.637079] libphy: gmac0: probed [ 8.665789] rmmod_device_driver
[ 8.672608] rmmod_device_driver()197 WARN: get power supply failed [ 8.679583] insmod_host_driver
[ 8.691960] [sunxi-ehci0]: probe, pdev->name: 5101000.ehci0-controller, sunxi _ehci: 0xffffff8008b291c0, 0x:ffffff8008b67000, irq_no:161 [ 8.706028] sunxi-ehci 5101000.ehci0-controller: SW USB2.0 'Enhanced' Host Co ntroller (EHCI) Driver [ 8.716181] sunxi-ehci 5101000.ehci0-controller: new USB bus registered, assi gned bus number 3 [ 8.722175] sunxi-gmac gmac0 eth0: eth0: Type(7) PHY ID 001cc916 at 0 IRQ pol l (gmac0-0:00) [ 8.735662] sunxi-ehci 5101000.ehci0-controller: irq 353, io mem 0x0000043c [ 8.737527] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.765649] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 8.765845] sunxi-ehci 5101000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 8.766371] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 8.766377] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 8.766381] usb usb3: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Dr iver [ 8.766385] usb usb3: Manufacturer: Linux 4.9.191 ehci_hcd [ 8.766389] usb usb3: SerialNumber: sunxi-ehci [ 8.768665] hub 3-0:1.0: USB hub found [ 8.768735] hub 3-0:1.0: 1 port detected
[ 8.770211] [sunxi-ohci0]: probe, pdev->name: 5101000.ohci0-controller, sunxi _ohci: 0xffffff8008b29550 [ 8.770643] sunxi-ohci 5101000.ohci0-controller: SW USB2.0 'Open' Host Contro ller (OHCI) Driver [ 8.770693] sunxi-ohci 5101000.ohci0-controller: new USB bus registered, assi gned bus number 4 [ 8.770876] sunxi-ohci 5101000.ohci0-controller: irq 354, io mem 0xffffff8008 552614 [ 8.838252] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 8.838258] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 8.838263] usb usb4: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 8.838266] usb usb4: Manufacturer: Linux 4.9.191 ohci_hcd [ 8.838270] usb usb4: SerialNumber: sunxi-ohci [ 8.840647] hub 4-0:1.0: USB hub found [ 8.840739] hub 4-0:1.0: 1 port detected [ 8.957934] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0 [ 8.980285] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined. [ 9.004113] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 9.025815] [STA_WRN] !!! xradio_remove_interface: vif_id=0 [ 9.034241] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0 [ 9.048358] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined. [ 9.072500] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 14.833591] systemd-journald[971]: Failed to set ACL on /var/log/journal/b2a6 c3288af54222b0308c96c71df261/user-1000.journal, ignoring: Operation not supporte d [ 14.925634] PVR_K: 1727: RGX Firmware image 'rgx.fw.22.102.54.38' loaded [ 62.846306] random: crng init done [ 62.850109] random: 7 urandom warning(s) missed due to ratelimiting [ 69.152147] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 70.757807] [STA_WRN] !!! xradio_remove_interface: vif_id=0 [ 70.766572] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0 [ 70.780466] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined. [ 70.804270] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 72.409230] [STA_WRN] Freq 2437 (wsm ch: 6) prev: 3. [ 72.414838] wlan0: authenticate with 18:34:af:96:04:7a (try 1) [ 72.467158] wlan0: authenticated [ 72.470878] [STA_WRN] Freq 2422 (wsm ch: 3) prev: 6. [ 72.473733] [TXRX_WRN] [RX] IF=0, No key found. [ 72.481585] [STA_WRN] Freq 2437 (wsm ch: 6) prev: 3. [ 72.487173] wlan0: associate with 18:34:af:96:04:7a (try 1) [ 72.499465] wlan0: RX AssocResp from 18:34:af:96:04:7a (capab=0x1411 status=0 aid=20) [ 72.508244] wlan0: associated [ 72.513719] [AP_WRN] [STA] ASSOC HTCAP 11N 58 [ 72.531028] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 72.564273] [TXRX_WRN] drop=1440, fctl=0x00d0. sonic@SonicPad:~$
Okay, fine. Plug in the Printer and run "dmesg" again. This time only the last 20 to 30 lines of the output should be sufficient.
I'm not sure why you don't have 'lsusb' installed, but you could and should install it via: 'sudo apt-get install usbutils' because also some Klipper utilities depend on that.
I'm not sure why you don't have 'lsusb' installed, but you could and should install it via: 'sudo apt-get install usbutils' because also some Klipper utilities depend on that.
lsusb:
sonic@SonicPad:~$ lsusb Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
dmesg:
[ 9.102408] usb usb3: Manufacturer: Linux 4.9.191 ehci_hcd [ 9.108565] usb usb3: SerialNumber: sunxi-ehci [ 9.115844] hub 3-0:1.0: USB hub found [ 9.120170] hub 3-0:1.0: 1 port detected
[ 9.131907] [sunxi-ohci0]: probe, pdev->name: 5101000.ohci0-controller, sunxi _ohci: 0xffffff8008b29550 [ 9.142799] sunxi-ohci 5101000.ohci0-controller: SW USB2.0 'Open' Host Contro ller (OHCI) Driver [ 9.152677] sunxi-ohci 5101000.ohci0-controller: new USB bus registered, assi gned bus number 4 [ 9.162511] sunxi-ohci 5101000.ohci0-controller: irq 354, io mem 0xffffff8008 552614 [ 9.234390] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.241980] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 9.250053] usb usb4: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 9.258064] usb usb4: Manufacturer: Linux 4.9.191 ohci_hcd [ 9.264233] usb usb4: SerialNumber: sunxi-ohci [ 9.271532] hub 4-0:1.0: USB hub found [ 9.275858] hub 4-0:1.0: 1 port detected [ 14.867091] systemd-journald[970]: Failed to set ACL on /var/log/journal/b2a6 c3288af54222b0308c96c71df261/user-1000.journal, ignoring: Operation not supporte d [ 14.967294] PVR_K: 1726: RGX Firmware image 'rgx.fw.22.102.54.38' loaded [ 63.378034] random: crng init done [ 63.381840] random: 7 urandom warning(s) missed due to ratelimiting [ 69.151495] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 70.765875] [STA_WRN] !!! xradio_remove_interface: vif_id=0 [ 70.774544] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0 [ 70.788459] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined. [ 70.812204] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 72.421932] [STA_WRN] Freq 2437 (wsm ch: 6) prev: 3. [ 72.427563] wlan0: authenticate with 18:34:af:96:04:7a (try 1) [ 72.479450] wlan0: authenticated [ 72.483147] [STA_WRN] Freq 2422 (wsm ch: 3) prev: 6. [ 72.488835] [STA_WRN] Freq 2437 (wsm ch: 6) prev: 3. [ 72.494448] wlan0: associate with 18:34:af:96:04:7a (try 1) [ 72.504732] wlan0: RX AssocResp from 18:34:af:96:04:7a (capab=0x1411 status=0 aid=35) [ 72.513509] wlan0: associated [ 72.518894] [AP_WRN] [STA] ASSOC HTCAP 11N 58 [ 72.536603] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 72.583478] [TXRX_WRN] drop=1440, fctl=0x00d0. sonic@SonicPad:~$
So from what I see is that the pad does not recognise your printer at all. Btw, have already tried different USB ports?
So from what I see is that the pad does not recognise your printer at all. Btw, have already tried different USB ports?
Yeap I try all 4 port usb and nothing I try too conect for my 2nd printer Voron switchwire and this same NO MCU;/ ( there is SKr Mini e3 v3)
Original Klipper Sonic Firmware working normally with Voron and Delta but I prefer this Debian is better and fresh Klipper.
Okay then, I don't know how, but it looks like something went wrong during installation and as you state that with SonicOS it was working, I assume your USB ports are fine.
So I would suggest to re-flash the Debian Image, as this is the fastest option. After a successful flash I would check the working condition of the USB before doing anything else.
with the given commandos of 'lsusb' and 'dmesg' - there should be changing output when a printer is connected and disconnected again.
W porządku, nie wiem jak, ale wygląda na to, że coś poszło nie tak podczas instalacji, a ponieważ twierdzisz, że z SonicOS działało, zakładam, że twoje porty USB są w porządku.
Sugerowałbym więc ponowne flashowanie obrazu Debiana, ponieważ jest to najszybsza opcja. Po udanym flashowaniu sprawdziłbym stan działania USB przed zrobieniem czegokolwiek innego.
z podanymi komendami 'lsusb' i 'dmesg' - po podłączeniu i ponownym odłączeniu drukarki powinny występować zmiany wyjścia.
very much thanks for your time and help ... I dont know whats going on :( I reinstall too new Build Debian Sonic and nothing;/
The kernel is the same as the stock SonicPadOS, so if the stock os recognized it, it should work with Debian.
What's the output of?:
ls /dev/serial/by-id/
Guys Working:)
Yeasterday I change 3 cable includes cable from Sonic and no working;/ Today I find shortly cable plug to my mainboard and find MCU:)
Very thanks for fast contact and help:)
@Jpe230 you can close this Topic :)
My Debian Sonic pad can't find mcu I plug in by USB:
I using by Kiauh get mcu and see: No MCU found! MCU either not connected or not detected!